BOYA BY-WM2G Wireless Microphone User Guide
- June 1, 2024
- Boya
Table of Contents
- Safety information
- Package contents
- Transmitter
- How to use it
- Receiver connect to the camera
- Transmitter
- Receiver connect to the smartphone
- Receiver connect to the Gopro
- Installing or uninstalling clip
- Features
- Specifications
- MAINTENANCE
- FCC STATEMENT
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BOYA BY-WM2G Wireless Microphone User Guide
Thank you for choosing Boya BY-WM2G.
Boya BY-WM2G is a compact wireless microphone, designed for DSLR cameras, smartphones, Gopro Hero 4, 3, etc.
Safety information
This symbol indicates that there are important operating and maintenance instructions in the literature accompanying your microphone.
-
Please read these instructions for use thoroughly before you use this new equipment for the first time.
It contains everything you need to know in order to avoid damage to persons or property. -
Heed all warnings and follow all instructions.
-
Do not use this microphone near water and clean only with a dry cloth.
-
Only use attachments/accessories specified by the manufacturer.
-
Refer all servicing to qualified service personnel, Servicing is required when the apparatus has been damaged in any way, such as, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 6. To protect the device from damage or malfunction, do not expose this device to rain, moisture, or excessive humidity.
-
Batteries should not be exposed to excessive heat, such as direct sunlight, fire, or being left in a hot car.
-
Take great care when using the microphone around moving objects or in other situations where the cable could be suddenly tugged or pulled.
Package contents
- Transmitter
- Receiver
- Lavalier/lapel microphone
- 3.5mm to TRS audio output cable
- 3.5mm to TRRS audio output cable
- 3.5mm to 10 PIN USB audio output cable
- Cold-shoe mount
- Hard case
- User Guide
Transmitter
-
Microphone Input
- Connect the supplied lavalier microphone here.
- Fully insert the microphone’s 3.5mm plug and make sure it clicks into place.
-
Line In
-
Power LED
-
The power LED flashes blue when the unit is on.
-
The power LED glows red when power is low.
For more details about LED indicator, please refer to the following: status| Receiver| Transmitter
---|---|---
Unitis turned ON| Flashing
Wireless communication is established| Flashing continually every 2.5 seconds
Receiver unit s turmed OFF (Transritter is til ON)| Off| Flashing
Transmitter unit is turned OFF(Receiver is stl ON)| Flashing| off
Low power| Flashing in red -
Power OFF/ON
-
Button +/-
This button is for setting the connection signal.
For details, please see “How to connect transmitter and receiver” from page 8-page 11. -
Antenna
Please don’t touch here during using, otherwise, it will affect the signal. -
Battery compartment
Accommodates one AA battery.
For more details, please see “Installing batteries” on page 8. -
Clip
For more details, please see “Installing or uninstalling clip” on page 13.
Receiver
Earphone Jack
(3.5mm diameter stereo mini jack) To monitor the receiver output, connect the
headphones to this connector.
NOTE
Do not connect headphones with a monaural mini jack.
This may lead to short-circuiting of the headphone output, resulting in
distorted sound output.
LINE OUT (audio output) Jack
For using Gopro, connect one end 90°plug of the supplied TRS stereo 3.5mm mini output cable here, and the other 10 pin plug to the Gopro.
If you want to connect with mobile devices (smartphones / tablets) or DSLR
cameras, we have 2 other different cables included.
Power LED
For more details, please see “”Power LED” on page 4.
Power OFF/ON
Volume +/-
Press these buttons to set the attenuation level of the input signal.
Antenna
Please don’t touch here during
using, otherwise, it will affect the signal.
Battery compartment
Accommodates one AA battery. For more details, please see “Installing
batteries” on page 8.
Clip
For more details, please see “Installing or uninstalling clip” on page 13.
Shoe Mount Adapter
Precautionary measures when using batteries Batteries/power packs, if inappropriately handled, can run out or explode.Please observe the following notes on safety when handling batteries to be used in this device:
- Use only batteries mentioned in these operating instructions.
- Do not lay the batteries in a fire and do not expose them to direct heat.
- In order to avoid damage to the product you must make sure that you remove the batteries,if you do not use the product over a longer period of time or if the batteries have been discharged.
- If battery fluid comes into contact with skin or clothes, rinse it off immediately with fresh water.
What’s difference?
-
3.5 mm TRS connector
For cameras, camcorders, audio recorders and other audio/video recording devices.
-
3.5 mm TRRS connector
For Smartphone, tablet or Mac
-
3.5mm to 10 PIN USB Audio Output Cable
How to use it
Insert batteries in the transmitter and receiver units
- Both transmitter and receiver requires one AA size battery.
- Slide and remove the transmitter’s battery compartment cover.
- Insert one battery.
- Close the battery compartment cover. 5. Repeat steps 2 to 4 to insert battery into receiver.
Connecting the transmitter and receiver
Receiver connect to the camera
- Mount receiver to cameras, camcorders, audio recorders and other audio/video recording devices.
- Using TRS cable, plug the 3.5 mm connector into the audio jack of your camera.
- Insert the other end of the connecting cable into the receiver “LINE OUT” jack. . Insert earphone into receiver * ” for monitoring sound.
Transmitter
- Insert the lavalier/lapel microphone into transmitter ” “.
- Slide the power ON/OFF switch to the ON position (the LED indicator will turn blue)
- Use the belt clip on the back to attach to a belt, or the transmitter simply can be put into a pocket.
If transmitter and receiver connect, the light will flash every 2.5 seconds.
Otherwise, the light will flash rapidly.
Before leaving the factory, the wireless connection of the transmitter and
receiver will be have been established.
If transmitter and receiver disconnect, please follow below steps:
- Turn on the receiver
- Press the button “+” and “-” for 3 seconds at the same time. 3. Repeat steps 1 to 2 to set up the transmitter.
If the LED light of both the transmitter and receiver flashes blue, the connection was successful. Otherwise, repeat steps 1-3.
Receiver connect to the smartphone
- Mount the receiver to the smartphone.
- Using 3.5mm to TRRS cable, plug the TRRS connector into the audio jacket of your smartphone.
- Insert the other end of the connector into the receiver “line out” jacket. 4. Insert the earphone into receiver * §3″ for monitoring sound.
- Slider the power ON/OFF switch to ON position (the LED indicator will light in blue).
Caution: Please do not mix up audio cable, for details, please refer to
“What’s difference on page 7″
Receiver connect to the Gopro
- Mount receiver to Gopro.
- Use the 3.5mm to 10 pin cable, plug the 10 PIN USB connector into the audio jack of your Gopro.
- Insert the 90° plug of the connecting cable into the receiver “LINE OUT” jack.
- Insert earphone into receiver “ {3 ” for monitoring sound.
- Slide the power ON/OFF switch to the ON position (the LED indicator will turn blue).
Installing or uninstalling clip
- Clip is mounted on the microphone before leaving factory.
- Both transmitter and receiver include clip, that means you can mount them in any place you want.
- You can adjust the direction of the microphone by rotating the clip.
If the receiver needs to be mounted onto a camera hot/cold shoe, please follow below steps:
-
Push the clip to the right side.
-
Screw the shoe mount adapter to receiver as shown.
-
Mounted receiver onto camera hot/cold shoe.
Features
- Clear sound recording
- Compatible with DSLR cameras, smartphones, Gopro Hero 4, 3 etc
- Light and compact for easy carrying
- Omnidirectional lavalier microphone
- Easy to use
- Hard case included
- Standard camera shoe mount and clip included
- Up to 15m (49ft) operation range
- Power Supplied by two AA batteries
Caution : Hero 6&5 need a Pro 3.5mm Mic Adapter (not include)
Specifications
RF Modulation: | GFSK (Gauss frequency Shift Keying) |
---|---|
Frequency band: | 2.4GHz (2405-2478MHz) |
Frequency response: | 35Hz-14KHz£3d8 |
Signal/Noise: | 7648 or more |
Distortion: | 0.19% or less (320, 1 KHz,65mW output) |
RF output level: | 2mw |
Earphone output level: | 320,65mW |
Reception sensitivity: | -85d8 +/- 3dB / 0dB=1V/Pa, 1ktz |
Audio input connector: | 3,5mm mini jack |
Operation range: | 15m (49) |
Power requirements: | 1.5V DC (One AA size battery) |
Consumption power: | Transmitter: 1.5V/120 mA |
Receiver: 1.5V/120 mA
Batery life:| Transmitter: Approx. 3.0 hours Recelver: Approx. 3 hours
Dimensions:| Transmitter: 60mm x 86mm x28mm (W/H/D) (236 x 3.3 x 1.1
inches)
Receiver: 60mm x 86mm x41mm (W/H/D) (236 x 3.3 x 1.61 inches)
Weight:| Transmitter: 1369 (4.3702) (Without battery)
Receiver: 1529 (4.8902) (Without battery)
CAUTION
- Please only use our original Audio Signal Cable which is included.
- The operation range given is only the approximate value that applies when there are no obstructions between the transmitter and receiver. This distance will vary depending on metal objects, people and other obstructions and on the signal strength.
- You can adjust the direction of the microphone to your mouth by rotating the clip.
IMPORTANT
- If you do not intend to use the wireless microphone for a long period time, please remove the batteries from both the transmitter and receiver.
- Do not touch the lavalier/lapel microphone, transmitter and receiver while recording, as this will cause noise to be recorded.
- Do not let the transmitter get close to high-voltage equipment or to devices that emit strong electromagnetic fields, otherwise, it may cause distortion.
- Do not use or leave the transmitter and receiver in hot, humid places.
- Do not leave the receiver attached to the camera when storing the camera in a case.
- Do not mix up the use of the transmitter and receiver.
WARNING
- Keep the wireless microphone out of the reach of children.
- Never use leaking batteries and never expose batteries to excessive heat or fire.
MAINTENANCE
-
Do not operate the device with wet hands .
-
Clean the equipment only in the way described in the instructions for use.
-
Take care to prevent the equipment from dropping down.Make sure that the device is properly fastened and reliably mounted. If the device has dropped down on the floor have it inspected by a skilled electrician before you switch it on again.
-
Should the equipment be damaged or defective,or if you notice a scorching smell:
Interrupt the electric power supply immediately by removing the batteries.Do not operate the device with a damaged housing,do not repair the device yourself. Have the device only repaired by a skilled electrician. -
Always keep your device in good condition, as specified in these instructions for use.
-
Do not open the device.
WARNING
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a partic- ular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>