BOYA WM3D Wireless Microphone Instruction Manual

BOYA WM3D Wireless Microphone

We thank you for your decision and wish you much pleasure and success with your new device.

Introduction

The BOYA Walimex pro-WM3D & WM3U Wireless Microphone for recording sound. It can be used both indoors and outdoors. The charging case is used to store and
charge the batteries. With the microphone, you greatly improve the sound quality of a video recording, e.g. from a smartphone.
Dedicated sound recordings also achieve a very high quality.
Your package includes the following main features

• Innovative storage and charging case with integrated battery for safe storage and up to 2x full charging on the go.
• Universal use thanks to 3 different adapters
• Up to 4.5 or 8 hours of continuous use thanks to state-of-the-art, compact Li-ion batteries
• Excellent omnidirectional microphone with sensitivity from 20 Hz to 20 kHz and 48 kHz sampling rate, perfect for speech, vocals, and music.

WARNING:

• Read these instructions carefully before using your new device for the first time. They contain everything you need to know to avoid personal injury and damage to property.
• Observe all safety instructions in this user manual.
• Keep these instructions in a safe place. Pass these instructions on to the new owner if you sell or otherwise transfer the device.

How to understand the instruction manual

Markings on the device
This marking means that your device should only be disposed of in local disposal points.

Markings in the manual

Important safety notes

CAUTION

• Cautions when using rechargeable batteries Do not place the battery in a fire or expose it to direct heat.
• Do not charge the battery unattended.
• Disconnect the charger from the mains after charging is complete.

Danger due to humidity

• Do not use the item in rain or snowfall.
• Moisture ingress can impair the functionality of the item.

Unpacking and checking the device

1. Carefully unpack the scope of delivery.
2. Check whether the scope of delivery is complete
   • 1x Boya Walimex pro WM3D/ WM3U Wireless Microphone with built-in transmitter
   • 1x Receiver with socket for exchangeable connectors
   • 1x Lightning adapter (only for WM3D) / 1x USB-C adapter (only for WM3U)
   • 1x TRS jack plug 3.5 mm
   • 1x TRRS jack plug 3.5 mm
   • 1x Storage case with built-in battery and charging function
   • 1x Foam windscreen
   • 1x Furry windscreen
   • 1x USB charging cable
   • 1x Safety instruction sheet
3. Check whether all parts of the unit are undamaged.
   NOTE: Ifthe scope of delivery is incomplete or damaged, please contact into@toto-walser.de.

Overview of the components

• 1. Microphone with transmitter (TX)
• 2. Microphone protection cover, microphone position
• 3. Clothes clip
• 4. Function indicator (LED)
• 5. On Off / Mute button
• 6. Charging contacts
• 7. Gain control
• 8. Receiver (RX)
• 9. Interchangeable adapter for recording device (here: Lightning)
• 4. Function indicator (LED)
• 6. Charging contacts (on the back)
• 10. On / Off button
• 11. Storage and charging case
• 12. Pairing button
• 13. Lock
• 14. Charging indicator
• 15. USB-C charging socket (back)
• 16. Storage and charging recesses tor microphone and receiver
• 17. Lightning adapter for iOS (only for WM3D)
• 18. USB-C adapter (only for WM3U)
• 19. TRRS adapter
• 20. TRS adapter
• 21. Furry windscreen
• 22. Foam windscreen
• 23. USB charging cable

Operation

WARNING
Observe the satety instructions in the respective sections for all activities.

Unpacking and preparing
On delivery, the charging contacts of the transmitter and receiver (6) are each secured with a tilm. Pull ott these tilms to make them ready for operation.

Charging the batteries
The system features three batteries, one in the charging case (11) and one each in the transmitter (1) and receiver (8).
Charge the battery in the charging case by connecting it to a suitable power source (e.g. mains adapter, power bank, PC, USB socket) via the charging socket (15) and the USB charging cable (23).
The four LEDs of the charging indicator (14) flash in sequence, indicating the charging status at the same time. When the charging process is tinished, the indicator stops tlashing.
You charge the transmitter and receiver by placing them in the case and closing the lid. The leftmost LED flashes for charging the transmitter, the rightmost LED flashes for charging the receiver.
When the charging process is tinished, the respective indicator stops flashing.
As soon as you place the transmitter and receiver in the case and connect it to the power supply, all three batteries are charged.

CAUTION
Do not charge the batteries unattended and do not leave them permanently plugged into the power suPPly, e.g. overnight.

Switching on, switching off
The transmitter and receiver switch on automatically as soon as you open the lid of the storage case. They also switch ott again when you close the lid. This only applies when the transrmitter and receiver are in the case.
You can switch on both devices manually by pressing and holding the on/ott button (5) respectively (10).
As soon as the function indicator (4) lights up or flashes, the devices are switched on.

Pairing
There are three methods of pairing the transmitter and the receiver.

• The transmitter and receiver are automatically paired when the charging case (11) is opened and the devices are switched on. As soon as the function indicators (4) light up solid blue, the pairing is successful. To trigger this pairing, close the case with the devices inside and open it again.

• The transmitter and receiver are paired by pressing the pair button (12) twice while the devices are in the case. The function indicators(4) flash. As soon as they light up
  continuously, the pairing is successful.

• Pair the transmitter and receiver outside the case by bringing the two devices close together and then simultaneously or in quick succession by pressing the on/off buttons (5) and (10) each twice in quick succession. The function indicators(4) flash during the process. As soon as they light up continuously, the pairing is successful.

Connection to recording devices
Depending on the recording device, use the appropriate adapter too connect it to the receiver. To do this, simply insert the respective adapter with the contacts to the device into the holder as shown
here:

• Use the Lightning adapter (17, only with WM3D) for iOS devices such as iPhones and iPads.
• Use the USB-C adapter (18, only with WM3U) for devices with USB-C connection, e.g. some iPads, Android devices, PCs with USB-C or USB-C adapters.
• Use the TRRS adapter (19, recognisable by the four contacts) for smartphones, laptops, tablets and other recording devices with a 4-pin 3.5 mm jack socket.
• Use the TRS adapter (20, recognisable by the three contacts) on DSLR cameras, camcorders and other recording devices with a 3pin 3.5 mm jack socket.
  Then plug the receiver into your recording device with the matching connector. From now on you are ready to record!

Tips for use

Radio connection
The range between transmitter and receiver is up to approx. 20 metres. This applies only as the crow flies without obstacles such as walls or metallic objects like tripods. Ideally, check the connection
on site before you start recording. If the transmitter or receiver is moving, noise or a (short or tinal) break in the connection may occur if there are obstacles. As soon as the connection is re-established,
the sound will continue to be crystal clear.

Sound quality
Make sure that the microphone is not rubbing anywhere or being touched during recording. In case of wind, draught, loud ambient noise or a loud voice (singing), it is advisable to attach one ot the two windscreens. These efficiently prevent or reduce wind noise and plosives.

Muting
The speaker can mute the microphone by briefly pressing the On/Off / Mute button (5) once. The function indicator flashes slowly in red. To switch oft, press the key again.

Recording Level
Change the recording level by operating the gain control (7). You should set the level betore recording, it possible do not change it during recording.

Light signals
Light signals of charging case

Light signals of transmitter and receiver:

Transporting and storing the unit

Transport and store the components of the set in a dry and dust-free place.

Cleaning

NOTE: Only use the cleaning agents specified in the table below.

Technical Specifications

Disposal and environmental protection

Please dispose of the appliance at one of the local disposal points. This service is tree ot charge for you.

WALSER GmbH & Co. KG
Senefelderstraße 23
86368 Gersthofen
info@walser.de
www.walser.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>