SW-MOTECH KFT.13.849.70000B TRAX ADV Aluminum Case System Instruction Manual

ANBAUANLEITUNG
mounting instructions
KFT.13.849.70000/B

TING INSTRUCTIONS = READ AND SAVE THESE MOUNTING INSTRUCTIONS
Revision:00 – Datum / Date: 05 – 2022

PRO side carrier
Thank you for choosing this premium product from SW-MOTECH.
Please carefully read and understand all instructions, safety messages, and warnings in this mounting instruction prior to installation and use of this product to avoid injury.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications], are also available for download at our webshop. Keep these mounting instructions as a reference.
SW-MOTECH assumes no Liability for damage caused by improper installation and/or maintenance work!

SAFETY ALERT SYMBOL

This safety alert symbol is used throughout these mounting instructions to warn of the possibility of death, bodily injury or other warnings. The words DANGER, WARNING, and CAUTION are used with this safety alert symbol to convey important safety messages and information related to the installation and use of this product. These words  along with the safety alert symbol mean:
DANGER: Indicates a hazardous situation that, if not avoided, will result in death or serious injury!
WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury!
CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury!
NOTICE: Important information, but not death or injury related [property damage only)!
WARNING: The installation and/or maintenance of this product requires advanced mechanical skills, the proper tools, and a thorough understanding of tool use and torque specifications.
For your own safety, SW-MOTECH recommends having installation and/or maintenance carried out by a qualified and certified motorcycle mechanic.
WARNING: Should you choose to self-install this product, carefully and completely read all installation and safety instructions before installation and use, and follow all the directions and safety precautions given in the mounting instructions to avoid serious injury or death. Also, pay attention to all relevant information in the vehicle manual during installation and use.
IF YOU DO NOT UNDERSTAND ANY PART OF THESE INSTRUCTIONS OR NEED CLARIFICATION OF ANY INSTRUCTION, DO NOT ATTEMPT TO  MOUNT THIS PRODUCT WITHOUT CONTACTING SW-MOTECH FOR ASSISTANCE. PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included.
CAUTION: Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the engine/exhaust cool off if necessary.  Disconnect the vehicle battery when working on the electrical system. Use appropriate tools and wear always safety glasses and hand protection. Have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer’s specifications or replaced by parts and hardware delivered by SW-MOTECH.
WARNING: Secure all threads, unless otherwise specified, with a medium- a strong-strength liquid thread locker. Torque specifications undefined by
SW-MOTECH must be obtained from the vehicle manufacturer or by a certified motorcycle workshop!
FUNCTION CHECK: After installation also make sure that no moving parts are obstructed, and the function of the vehicle is not hindered in any way. Cables and hoses must not rub and/or be pinched.
WARNING: Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all connections and the proper fit of the product. Installed accessories can change the driving behavior/stability of the vehicle.

: Nr.
: No.| Art.-Nr.
Item No.| Part| Quantity| Nem
---|---|---|---|---
1| KFT.13.849.001L / R| Mounting Bracket; left / right| 2/2|
2| M6 x 40; DIN 6912| Hexagon Socket Screw, short head; black| 2/2| 9
3| -9 6,4; DIN 9021| Washer; black| 2/2|
4| (0 20/06,2/h 12| Spacer; height 12 mm| 2/2|
5| – BB.180.090.062.090.060.01| Flanged Spacer| 2/2|
6| M8 x 40; DIN 6912| Hexagon Socket Screw, short head; black| 2/2| 20
7| 98,4; DIN 9021| Washer; black| 2/2|
8| (925/08,4/h15| Spacer; height 15 mm| 2/2|
9| (012/a84/h4| Spacer; height 4mm| 2/2|
| | | |
10| KFT.06.921.003L /R| : Mounting Bracket; left / right| 2/2|
11| M8 x 45; DIN 6912| Hexagon Socket Screw, short head; black| 4/4| 20
12| 9 8,4; DIN 125| ; Washer; black| 4/4|
13| 015/084/h5| : Spacer; height 50mm| 4/4|
| | | |
14| KFT.22.892.004| Crossbar| 1/1|
15| KFT.13.849.971.01 / 972.01| Side Carrier| 2/2|
16| KFT.00.152.SV.8| Quick Fastener Set with Lock Washers| 1/1|
| | | |
| | | |
| | | |
| | | |
| | | |

Note: All measurements in millimeters. b The second number indicates the total quantity of the part in the delivery. c No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING = READ AND SAVE THESE MOUNTING INSTRUCTIONS

WARNING: Always wear eye and hand protection!
WARNING: Always use appropriate tools!
Remove on both sides the shown screws from the rear of the vehicle.

Attach the mounting brackets [1] on both sides to the vehicle.
WARNING: Use liquid thread locker!
Do not fully tighten the screws yet.

Loosen the screws on both sides of the vehicle and remove the footrest mounts.

Attach the mounting brackets [10] with the footrest mounts on both sides of the vehicle.
**WARNING:** Use a liquid thread locker!
Do not fully tighten the screws yet.

Connect the side carriers (15) to the mounting brackets [1) and (10) and the crossbar (14) with the fasteners (16). Secure the fasteners with the lock washers.
Once all parts are evenly positioned without excess tension, tighten the screws (2), (6), and (11) as specified. A\NOTICE: The Anti-Theft Device is sold separately.

PRODUCT SPECIFIC INFORMATION

WARNING: The indicated maximum load is inclusive of the weight of the case/luggage and adapter kit. The maximum vehicle load specified by the manufacturer must not be exceeded!
NOTICE: The side carriers are designed exclusively for the use of SW- MOTECH Adapter Kits.
NOTICE: Dismount the side carriers when traveling without cases/luggage.
Always use the side carriers in pairs.
WARNING: Make sure that after attaching the Luggage to the vehicle it is
NOT in the exhaust flow! Dangers of burns!
NOTICE: Observe the country-specific regulations concerning vehicle registration/operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.

MOUNTING INSTRUCTIONS

Revision:02 – Datum / Date: 06 = 2018
Adapter kit for PRO side carrier –
TRAX ADV/ION/EVO

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Installation and/or maintenance of this product require good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle,

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority. PREPARATION: Read the mounting instructions carefully and make sure that all items on the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer’s specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation makes sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

Nr.
No.| Art.-Nr.
Item No| Part| Quantity| N.M
---|---|---|---|---
1| KFT.00.152.070L/R| Latch Hook; left / right| 2/2| 9
2| Mé x 16; ISO 7380| Lionshead Screw| 4/4|
3| KFT.00.152.071| Guide Bolt| 8/8|
4| Mé x 20; DIN 7991| Countersunk Screw| 8/8| 9
5| Mé; DIN 6927| Lock Nut with Flange; black| 12/12|

• All measurements in millimeters. – ** The second number indicates the total quantity of the part in the delivery.
  *** No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING

NOTE: The illustration shows the mounting to the right PRO side carrier. Mount the parts to the left PRO side carrier in the same way as to the right PRO side carrier.
Attach the shown parts to your PRO side carriers (sold separately). Tighten the screws as specified in the parts list.
ATTENTION: To ensure the proper fit of your TRAX ADV / EVO / ION side case, adjust the latch hook (1) over the elongated holes (see detail drawing)! Make sure that the side case’s latch engages properly when mounted!

MOUNTING INSTRUCTIONS

Revision:03 – Datum / Date: 02-2021
RAX ADVENTURE ALU-BOX

 Thank you for choosing this premium product from SW-MOTECH.
[$} Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE  certifications), are also available for download at our webshop. >> www.sw-motech.com
Installation and/or maintenance of this product require a good technical understanding. For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop.
SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work.
Carefully follow all the directions given in the mounting instructions, Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as a reference.
This product was developed for vehicles in their original condition.
Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Installed accessories can change the driving behavior and/or stability of your vehicle.

GENERAL INFORMATION

Observe any country-specific legal or TUV regulations. If required, enter the installed parts into the vehicle documents with the appropriate inspection authority.
SECURITY
Please pay attention to the following information concerning the TRAX
ADVENTURE ALU-Boxx:
The TRAX ADVENTURE ALU-BOX is designed exclusively for mounting on SW-MOTECH QUICK-LOCK side carriers, QUICK-LOCK adapter plate and STEEL-RACK  adapter kit.
Modifications made to the cases will void any warranty.
ATTENTION: Riding with TRAX ADVENTURE ALU-BOX may affect the motorcycle’s driving and braking performance.
ATTENTION: TRAX ADVENTURE ALU-BOXES M & L must be used in pairs.
Make sure the weight is evenly distributed between left and right side case.
ATTENTION: Maximum load: Please refer to the mounting instructions of the SW- MOTECH QUICK-LOCK side carrier, ALU-RACK or STEEL-RACK.
Maximum speed with mounted cases: 130 km/h (80 mph).
ATTENTION: Make sure that the TRAX ADVENTURE ALU-BOX is properly attached to the particular adapter and fully engaged to all four mounting points! ALL latches  of the TRAX ADVENTURE ALU-BOX must be locked BEFORE riding with the TraX ® EVO / TRAX ADV lock cylinder set [sold separately) and remain closed while riding. Improperly mounted cases run the risk of detaching during transport.
CARE
To clean the TRAX ADVENTURE ALU-BOX, use warm, soapy water and a soft, clean cloth. Rinse with clean water. Do NOT use strong cleaning agents, rough cleaning tools, or a high-pressure washer!

PARTS LIST

Nr.
No.| Art.-Nr.
Item No| Part| Quantity| N.M
---|---|---|---|---
| | TRAX ADV ALU-BOX| 1/1|
| | | |
| ALK.00.733.041| Snap-Fit| 2/2|
| ALK.00.733.040 (L/R)| Lid Limiter| 2/2|
| ALK.00.733.042| Swivel Part| 2/2|
| 3 x 14; DIN 750| Lionshead Screw, self-tapping| 4/4| 0.5

• The second number indicates the total quantity of the listed part in the delivery.

www.sw-motech.com
Please visit our webshop for application charts and compatible accessories.

LID AND LOCK CYLINDER SET

Open the lid (TRAX ADV M/L/ top case)

1. Pull the latch of the lid upwards
2. and remove it from the latch bar.
3. Open the lid.

**Insertion of the TraX ® EVO / TRAX ADV lock cylinder set *
(TRAX ADV M/L/ Topcase)**

1. Insert the lock cylinders into the latches.

2. Secure the lock cylinders with the clamping plates.
   ATTENTION: Pay attention to the correct alignment of the clamping plates (as shown in the detailed drawings).

3. Insert the keys into the lock cylinders; open or close the lock cylinder as shown in the schematic drawing.
   ATTENTION: Use for lubrication graphite powder ONLY! * Sold separately.

LID LIMITER

Mounting the lid limiters
(TRAX ADV M / L / top case)

1. Open the lid. Attach the snap-fit (4) with the shown parts at the lid frame.
   Tighten the screws as specified in the parts list.

2. Attach the lid limiters (5) with the shown parts at the case frame.
   NOTE: Pay attention to left-right specifications for the limiters {in driving direction].
   Tighten the screws as specified in the parts list.
   Press the lid limiters onto the snap-fits.

3. Before closing the lid for the first time, the lid limiters must be compressed as shown in the drawing.
   While closing the lid, make sure that the lid limiters are not pinched between lid and case.

4. To remove the lid from the case (as shown on page 5], remove the lid limiters from the snap-fits first.

QUICK RELEASE FASTENER

Removing the lid (TRAX ADVENTURE M / L)

1. Press the quick release fastener down until it clicks into place and the button pops out.

2. Then remove the lid from the case.
   NOTE: If you have installed the lid limiters (5], they must be detached before removing the lid {as shown on page 4].

3. Press the button of the quick-release fastener to lock the replaced lid in place. Make sure that the quick-release fastener Snaps above.

Maintenance and cleaning of the quick-release fastener (TRAX ADVENTURE M / L)

1. Loosen the six screws on the inner side of the case and remove the quick-release fastener.
2. Loosen the screw of the button (fix with thumb and index finger).
3. Loosen the shown clip carefully and…
4. … remove the quick-release fastener and springs from the mounting plate.
5. Clean the components with clean water and let it air dry.
   Reattach all parts in reversed order.

MOUNTING

Attachment of TRAX ADVENTURE ALU-BOX M & L

1. Lead the four openings of the mounting rails onto the locating bolts of the mounted QUICK-LOCK adapter kit.
   Then press the TRAX ADVENTURE ALU-BOX slightly downward, until it properly rests on the QUICK-LOCK side carrier.
   ATTENTION: Make sure that all four locating bolts rest on at the same time.

2. Place the latch over the latch hook and…

3. … close the latch; check the proper fit of the TRAX ADVENTURE ALU-BOX on the QUICK-LOCK side carrier.
   ATTENTION: Make sure the closed latch is under sufficient tension! If not the latch hook must be readjusted!
   ATTENTION: Secure the TRAX ADVENTURE ALU-BOX with the separately available TraX ® EVO / TRAX ADVENTURE lock cylinder set at the QUICK-LOCK  side carrier before riding!

Attachment of TRAX ADVENTURE ALU-BOX M & L

1. Lead the four openings of the mounting rail onto the locating bolts of the mounted QUICK-LOCK adapter plate / STEEL-RACK adapter kit.
   Then press the TRAX ADVENTURE ALU-BOX slightly forward, until it properly rests on the QUICK-LOCK adapter plate / STEEL-RACK adapter kit.
   ATTENTION: Make sure that all four locating bolts rest on at the same time.

2. Place the latch over the latch hook and…

3. … close the latch; check the proper fit of the TRAX ADVENTURE ALU-BOX on the QUICK-LOCK Adapter Plate / STEEL-RACK Adapter Kit.
   ATTENTION: Make sure the closed latch is under sufficient tension! If not the latch hook must be readjusted!
   ATTENTION: Secure the TRAX ADVENTURE ALU-BOX with the separately available TraX ® EVO / TRAX ADVENTURE lock cylinder set at the QUICK-LOCK  adapter plate / STEEL-RACK adapter kit before riding!

MOUNTING INSTRUCTIONS

QLS.00.046.1510+
TRAX lock set with anti-theft protection PRO / EVO
ACHTUNG / ATTENTION
NEVER lubricate lock cylinders with oil! Use graphite powder only!

Nr.
No.| Art.-Nr.
Item No.| Anzaht
Quantity
---|---|---
| OLS.00.095.1510 (PRO)|
(1)| QLS.00.095.520| 2 /2
(2)| SV.ST.095.007.LK.02| 2 /2
(3)| ALK.00.165.A63| 2 /2
(4)| ALK.00.165.562| 7 /7
| |
| OLS.00.046.1510 (EVO)|
(1)| QLS.00.046.520| 2 /2
(2)| CAM.2312S10-1 BP| 2 /2
(3)| ALK.00.165.A63| 2 /2
(4)| ALK.00.165.562| 7 n

Copyright by
Errors and omissions excepted. Technical and design modifications are subject to change. SW-MOTECH GmbH & Co. KG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>