Munters RBS 3 Bird Scale User Manual
- June 7, 2024
- Munters
Table of Contents
RBS-3
Manual for use and maintenance
RBS 3
Bird Scale
Ag/MIS/ImGb-2675-12/18 Rev 1.0
P/N: 110239
RBS 3 Bird Scale
Manual for use and maintenance
Original instructions
This manual for use and maintenance is an integral part of the apparatus together with the attached technical documentation.
This document is destined for the user of the apparatus: it may not be reproduced in whole or in part, committed to computer memory as a file or delivered to third parties without the prior authorization of the assembler of the system.
Munters reserves the right to effect modifications to the apparatus in accordance with technical and legal developments.
Introduction
Disclaimer
Munters reserves the right to make alterations to specifications, quantities, dimensions, etc. for production or other reasons, subsequent to publication. The information contained herein has been prepared by qualified experts within Munters. While we believe the information is accurate and complete, we make no warranty or representation for any particular purposes. The information is offered in good faith and with the understanding that any use of the units or accessories in breach of the directions and warnings in this document is at the sole discretion and risk of the user.
Introduction
Congratulations on your excellent choice of purchasing an RBS-3!
In order to realize the full benefit from this product, it is important that
it is installed, commissioned, and operated correctly. Before installation or
using the fan, this manual should be studied carefully. It is also recommended
that it is kept safely for future reference. The manual is intended as a
reference for installation, commissioning, and day-to-day operation of the
Munters Controllers.
Notes
Date of release: July 2010
Munters cannot guarantee to inform users about the changes or to distribute
new manuals to them.
All rights reserved. No part of this manual may be reproduced in any manner
whatsoever without the expressed written permission of Munters. The contents
of this manual are subject to change without notice.
Scale Wiring Diagram
Scale Calibration
The scale calibration is an easy process and will be illustrated in the following steps:
|
SCALE CALIBRATION
---|---
| Channel-scale| Factor| offset
1| Feed/silo-1| 0.000| 0
2| Bird-2| 0| 0
3| None| 0| 0
4| None| 0| 0
CHANNEL 1
Press ENTER to Calibrate or RIGHT ARROW to change Factor or Offset
- The scale calibration table has 2 columns: channel-scale Factor and offset. The scale column is automatically filled according to the set up in the installation menu. If for example, you need to calibrate Silo-1, place the cursor on line number one and press Enter.
-
The bottom part of the table will change to the following
CALIBRATION PROCESS CHANNEL 1Press ENTER for Tare Registration
-
Make sure the silo is empty and steady and press Enter. The system will perform a check and its process will be illustrated in the following table:
CALIBRATION PROCESS CHANNEL 130%
-
After the process will be finished the next table will appear:
CALIBRATION PROCESS CHANNEL 1Place a known weight or start filling And press ENTER
- Use a known weight and enter its weight in Kg or in Lb or if you are using a truck, start filling the silo and press Enter.
The writing will change to the following:
CALIBRATION PROCESS CHANNEL 1
At the End, Enter the Filling weight 1
• When the truck finishes the loading, disconnect it from the silo and enter
the feed weight. If you are using a known weight enter its quantity.
• If you enter the weight in Lb then the scale factor will be in Lb and all
the weights will be in Lb. If you enter the weight in Kg then the scale factor
will be in Kg and all the weights will be in Kg.
-
The system will perform a check and its process will be illustrated in the following table:
CALIBRATION PROCESS CHANNEL 130%
-
If the calibration is successful a Good Calibration message will appear:
CALIBRATION PROCESS CHANNEL 1GOOD CALIBRATION. Factor is 104.5
Press ENTER. If you are using a weight remove it before pressing ENTER
The controller will identify if you are using a truck or a known weight at this check. If it is a truck, the weight will remain on the silo, and if not the weight will be tare again.
- Press MENU to Exit.
Warranty
Warranty and technical assistance
Munters products are designed and built to provide reliable and satisfactory performance but cannot be guaranteed free of faults; although they are reliable products they can develop unforeseeable defects and the user must take this into account and arrange adequate emergency or alarm systems if failure to operate could cause damage to the articles for which the Munters plant was required: if this is not done, the user is fully responsible for the damage which they could suffer.
Munters extends this limited warranty to the first purchaser and guarantees
its products to be free from defects originating in manufacture or materials
for one year from the date of delivery, provided that suitable transport,
storage, installation, and maintenance terms are complied with. The warranty
does not apply if the products have been repaired without express
authorization from Munters, or repaired in such a way that, in Munters’
judgment, their performance and reliability have been impaired, or incorrectly
installed, or subjected to improper use. The User accepts total responsibility
for incorrect use of the products.
The warranty on products from outside suppliers fitted to RBS-3, (for example
power supplies, cables, etc.) is limited to the conditions stated by the
supplier: all claims must be made in writing within eight days of the
discovery of the defect and within 12 months of the delivery of the defective
product. Munters has thirty days from the date of receipt in which to take
action and has the right to examine the product at the customer’s premises or
at its own plant (carriage cost to be borne by the customer).
Munters at its sole discretion has the option of replacing or repairing, free
of charge, products which it considers defective, and will arrange for their
despatch back to the customer carriage paid. In the case of faulty parts of
small commercial value which are widely available (such as bolts, etc.) for
urgent despatch, where the cost of carriage would exceed the value of the
parts, Munters may authorize the customer exclusively to purchase the
replacement parts locally; Munters will reimburse the value of the product at
its cost price.
Munters will not be liable for costs incurred in demounting the defective
part, or the time required to travel to the site, and the associated travel
costs. No agent, employee or dealer is authorized to give any further
guarantees or to accept any other liability on Munters’ behalf in connection
with other Munters products, except in writing with the signature of one of
the Company’s Managers.
WARNING : In the interests of improving the quality of its products and services, Munters reserves the right at any time and without prior notice to alter the specifications in this manual.
The liability of the manufacturer Munters ceases in the event of:
- dismantling the safety devices;
- use of unauthorized materials;
- inadequate maintenance;
- use of non-original spare parts and accessories.
Barring specific contractual terms, the following are directly at the user’s expense:
- preparing installation sites;
- providing an electricity supply (including the protective equipotential bonding (PE) conductor, in accordance with CEI EN 60204-1, paragraph 8.2), for correctly connecting the equipment to the mains electricity supply;
- providing ancillary services appropriate to the requirements of the plant on the basis of the information supplied with regard to installation;
- tools and consumables required for fitting and installation;
- lubricants necessary for commissioning and maintenance.
It is mandatory to purchase and use only original spare parts or those
recommended by the manufacturer.
Dismantling and assembly must be performed by qualified technicians and
according to the manufacturer’s instructions.
The use of non-original spare parts or incorrect assembly exonerates the
manufacturer from all liability.
Requests for technical assistance and spare parts can be made directly to the
nearest Munters office. A full list of contact details can be found on the
back page of this manual.
Munters Israel
18 HaSivim Street
Petach-Tikva 49517, Israel
Telephone: +972-3-920-6200
Fax: +972-3-924-9834
Australia Munters Pty Limited, Phone +61 2 8843 1594,
Brazil Munters Brasil Industria e Comercio Ltda, Phone +55 41 3317 5050,
Canada Munters Corporation Lansing, Phone +1 517 676 7070,
China Munters Air Treatment Equipment (Beijing) Co. Ltd, Phone +86 10 80 481
121
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>