cecotec ChopBeat 2000 Vindaloo Glass Electric Food Chopper Instruction Manual

CHOPBEAT 2000 VINDALOO GLASS
Food chopper
Instruction manual

SAFETY INSTRUCTIONS

Read these instructions thoroughly before using the device. Keep this instruction manual for future reference or new users.

• All safety instructions must be closely followed when using the appliance.
• Always disconnect the appliance from the power supply if it is left unattended and before assembly, disassembly, or cleaning.
• The device is not intended to be used by children. Keep the appliance and its power cable out of the reach of children.
• The appliance can be used by persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards  involved.
• Children must not play with the appliance.
• Strictly follow the instructions in this manual to avoid injury or damage to the appliance.
• Be careful when handling the cutting blades, when emptying the jug, and during cleaning.
• Switch off and unplug the appliance before changing accessories or nearby parts that move during use.
• Check the power cable regularly for visible damage. If the power cable is damaged, it must be replaced by the Technical Support Service of Cerotic or similar qualified personnel to avoid risks.
• This device is designed for domestic use only and is not intended for bars, restaurants, farmhouses, hotels, motels, and offices.
• The appliance is not intended to be operated by means of an external timer or separate remote-control system.
• Do not use accessories that have not been provided by Cerotic, as this could damage the product and cause injuries.
• Cleaning and maintenance tasks must not be carried out by children.
• Do not use the blender with hot or boiling liquids. Allow them to cool down before processing them.
• Ensure that the mains voltage matches the voltage specified on the device rating label and that the plug is earthed.
• Do not immerse the cable, plug, or any other non-removable part of the device in water or any other liquid or expose electrical connections to water. Make sure your hands are dry before handling the plug or switching on the device. – Do not plug the appliance into the power supply until it is fully assembled and make sure it is unplugged before disassembling the appliance or handling its blade.

PARTS AND COMPONENTS

Fig. 1

1. Fast speed button
2. Slow speed button
3. Motor unit
4. Chopper lid
5. Side blades
6.  Main blades
7. Chopping container

NOTE:
the graphics in this manual are schematic representations and may not exactly match the device.

BEFORE USE

• This appliance is packaged in a way as to protect it during transport. Take the device out of its box and remove all packaging materials. You can keep the original box and other packaging elements in a safe place. This will help you prevent damage to the device when transporting it in the future. In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.
• Make sure all parts and components are included and in good conditions. If there is any piece missing or in bad conditions, contact the official Cerotic Technical Support Service immediately.

Box content

• Food mincer
• Instruction manual

OPERATION

• Before using the electric mincer, make sure there is enough space inside the container to allow the blades to move freely. It is important that the container is not overfilled, as this could obstruct or hinder the proper rotation of the blades. Do not use the appliance if the container is empty.
• Do not use the appliance continuously for more than 20 seconds. After 20 seconds of continuous use, allow the appliance to cool down to room temperature (at least 2 minutes) before using it again.
• The blades of this appliance are sharp. Treat them with care at all times and never allow fingers, hair or clothing to come into contact with them. When the mincer is not in use, the blades should be stored in the cover provided.
• If you wish to remove the contents of the container with a spatula, first remove the blades.

Before using the product

1. Wash all parts of the mincer that will come into contact with food, i.e., the chopping container, the cover of the mincer and the top cover with warm soapy water, rinse and dry thoroughly.
2. Remove the covers from both blades. Place the blade faces down on a worktop, then push down on the plastic housing of the blades to release them. Be careful not to touch the cutting surfaces.
3. Wash the blades with warm, soapy water; rinse and dry them thoroughly. As soon as the blades are dry, place them in their covers for safety.
4. To replace the cover, place the blade face down on a worktop. Place the cover over the blade and press the cover down to secure it.
5. Unwind the power cord. Clean the entire motor unit with a soft cloth dampened with soapy water and then with a clean, damp cloth. Dry well. Do not immerse the motor unit, power cord, or plug in water.
6. If the appliance is not to be used immediately, install it completely. Place the covered blades in the container. Now place the cover on the container and then carefully place the chopper body under the cover.

Prepare and introduce the ingredients for chopping
Cut the ingredients into 25 mm cubes. If the food is very solid or dry, cut the pieces into smaller cubes. If the ingredients are very dry, it may be necessary to add some liquid. You should never try to chop only dry ingredients in the chopper.
Ice crushing
The maximum amount of ice that can be crushed at the same time is 8 ice cubes (not larger than 20 x 20 x 20 mm).
Assembly and operation of the product
Place the mincer on a stable surface, free from heat and humidity and within reach of a mains socket. Ensure that all parts that come into contact with food are clean.

1. Carefully remove the blade cover; be careful not to touch the blades. Insert the blade assembly into the shaft of the chopping container and press it into place. Once the blades are in position, you can insert the food. See the previous section for guidance on food preparation.
2. Fill the container with the prepared food. Although the maximum capacity of the vessel is 2000 ml, we strongly advise that no more than 500 ml be processed at a time. Refer to the “Recommended Operating Times” table for assistance.
3. The food level must never exceed the MAX mark on the chopping container.
4. When using the ice crusher, do not put more than 8 ice cubes in the container.
5. Place the chopper cover on the chopping container. Place the cover over the blade assembly and check that the blade assembly is centred and rotates freely. Make sure that the blades are not trapped by pieces of food.
6. Place the motor unit over the chopping container. Turn it slightly to make sure that it is well centred and that the blades are properly engaged. If the engine is in the right place, the weight of the engine unit will press down on the blade assembly.
7. Plug the appliance to a power supply and switch it on. You must ensure that the power cable is completely unwound.
8. The device has two speeds: low speed and high speed. Hold the mincer firmly and then press the corresponding button on the top of the motor unit to start processing the food.
9. Release the pressure to switch off the appliance.
   – Operate the appliance for short periods of time. Never let the engine run continuously for more than 20 seconds.
   – After 20 seconds of continuous operation, allow the engine to cool down to room temperature.
   – With some foods it may be necessary to stop the appliance and redistribute the food before continuing. Always unplug the appliance before removing the cover.

Pulse mode: make several short, high-speed pulses.
Removing the food

1. Disconnect the device from the mains.
2. Remove the motor unit and the top cover.
3. Remove the blades and place them in a safe place before emptying the food with a spoon.

After use

1. Unplug the device.
2. If the engine is hot, allow it to cool down completely.
3. Remove the motor unit and the top cover.
4. Lift the blades and place them in a safe place.
5. Pour the contents of the container with a spoon.

Recommended operation times

specified time has elapsed, allow the unit to cool down to room temperature.
Double blades| 500 g onion| Max 10 seconds
Single blade| 250 g peeled garlic| Max 10 seconds
Single blade| 200 g walnuts| Max 10 seconds
Single blade| Ice cubes 20 x 20 mm| Max 10 seconds

CLEANING AND MAINTENANCE

• Wash the container, top cover and blades with warm soapy water and dry them with a cloth. Be careful when handling the blades.
• The cover has a sealing gasket under the top edge. Always check after use that the gasket is completely clean and that nothing has adhered underneath it. To clean the gasket, carefully remove it, wash it in warm soapy water and dry it before replacing it in the cover. Never use the appliance if the sealing gasket is dirty or not properly installed. Fig. 2
• Clean the entire motor unit with a soft cloth dampened with soapy water and then with a clean, damp cloth. Dry well. Do not immerse the motor unit, power cord, or plug in water.
• After cleaning, assemble the device for storage. Place the covered blades in the container. Now place the cover on the container and then carefully place the chopper body under the cover.
• Loosely coil the power cord and store the appliance in a cool, dry cabinet out of the reach of children and pets.

TECHNICAL SPECIFICATIONS

Product: Chop Beat 2000 Vindaloo Glass
Product reference: 04858
Voltage: 220 – 240 V
Frequency: 50 – 60 Hz
Power: 500 W
Technical specifications may change without prior notification to improve product quality.
Made in China
Designed in Spain

DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC APPLIANCES

**** This symbol indicates that, according to the applicable regulations, the product and/or batteries must be disposed of separately from household waste. When this product reaches the end of its shelf life, you should dispose of the cells/batteries/ accumulators and take them to a collection point designated by the local authorities.
Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.
Compliance with the above guidelines will help protecting the environment.

TECHNICAL SUPPORT AND WARRANTY

Cerotic shall be liable to the end user or consumer for any lack of conformity that exists at the time of delivery of the product under the terms, conditions, and deadlines established by the applicable regulations.
It is recommended that repairs be carried out by qualified personnel.
If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact the official Cerotic Technical Support Service at +34 963 210 728.

COPYRIGHT

The intellectual property rights over the texts in this manual belong to CECOTEC INNOVACIONES, S.L. All rights reserved. The contents of this publication may not, in whole or in part, be reproduced, stored in a retrieval system, transmitted, or distributed by any means (electronic, mechanical, photocopying, recording or similar) without the prior authorization of CECOTEC INNOVACIONES, S.L.

www.cecotec.es
Cerotic Innovations S.L.
Av. Reyes Calicos, 60
46910, Alf afar (Valencia), Spain
EA01230710

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>