ARMOR UP 4 Plus 2 Practice Pcs CutOut Door Handle and Surround Trim Paint Protection Film Instruction Manual

ARMOR UP 4 Plus 2 Practice Pcs CutOut Door Handle and Surround Trim Paint

Protection Film

Specifications:

• Product Name: ARMOR UP 4+2 Practice Pcs
• Compatibility : 2023-24 Kia EV9
• Material : 8mil TPU Sticker
• Dimensions : 11 1/4″ (Length) by 3 3/4″ (Width)
• Available Colors:

1. All Black Gloss Finish
2. All Black Matte Finish
3. All Clear Gloss Finish
4. All Clear Matte Finish
5. Clear Surround & Black Gloss Finish
6. Clear Surround & Black Matte Finish

Product Usage Instructions

Package Contents
Your package contains:

• 4 regular pieces (2 front row doors, 2 back row doors)
• 2 extra/spare pieces
• 1 x squeegee included in the kit

You Will Also Need:

• Pressure sprayer or spray bottle
• Baby shampoo
• Pure/distilled water
• Microfiber towel

Installation Procedure:

1. Thoroughly clean, degrease, and prepare the installation area.
2. Mix SLIP solution: Fill 48-68 ounces of distilled water in a sprayer, add 3 drops of baby shampoo.
3. Install the Surround Piece first.
4. Do not dry-peel the sticker; generously spray the door handle area with the SLIP Solution.
5. Align the Surround Piece correctly and do not lift the sticker to reposition.
6. Spray with pure/distilled water and use a squeegee to remove bubbles.
7. Repeat the procedure for the Handle Piece and other pieces.

Manufacturer Disclaimer:
Do not use on repaired painted surfaces. Use a Pressure Hose at least 3′ away from the ARMOR UP kit on the door handle. Allow 48 hours to dry before washing the car. Use distilled water for both the SLIP & TACK solution.

Pro Tip:
Start with the ‘2nd-row rear passenger-side door’ for the Learning Curve effect, then proceed to the ‘front passenger-side door’ and ‘rear driver-side door’.

Compatible with 2023-24 Kia EV9, 8mil TPU Sticker Install Kit Scratch Protector
Dimensions : 11 1/4″(Length) by 3 3/4″(width)

AVAILABLE COLORS:
A total of 6 color options to choose from:

1. All Black Gloss Finish5.
2. All Black Matte Finish
3. All Clear Gloss Finish
4. All Clear Matte Finish
5. Clear Surround & Black Gloss Finish
6. Clear Surround & Black Matte Finish

YOUR PACKAGE CONTAIN

Every Kit contains :

• STICKERS
  

  • 4 regular pcs
  • 2 x front row doors
  • 2 x back row doors
  • + 2 extra /spare pcs to address the customer error.

• SQUEEGEE

  • 1 x squeegee included in the kit

YOU WILL ALSO NEED

MANUFACTURER DISCLAIMER:

• Do not use on repaired painted surfaces.
• Use a Pressure Hose at least 3’ away from the ARMOR UP kit on the door handle. Refer to video clip provided. Allow 48 hours to dry before washing the car.
• Use distilled water over tap water for both the SLIP & TACK solution.

INSTRUCTIONS

1. Thoroughly clean, DEGREASE and prepare the installation area.
2. How to mix SLIP solution:
   • Fill 48-68 ounces of distilled water in a 1/2 gallon pressured sprayer or spray bottle.
   • Start with 3 drops of baby shampoo. Add more for better glide.
   • Empty and rinse the sprayer with clean water before refilling
3. Install the Surround Piece first. Do Not Dry-Peel the Sticker
4. Generously spray the door handle area with the SLIP Solution.
5. Before removing the sticker from its plastic backing, generously spray it with SLIP solution. Begin peeling and continue spraying the SLIP solution to moisten the adhesive side. Refer to the video clip for guidance.”
6. Align the Surround Piece correctly. Ensure the edges are in the right position and do not overhang. Once laid, do not lift the sticker to reposition, GLIDE instead.
7. When placed perfectly, spray with PURE /DISTILLED WATER. BE CAREFUL!Do not lift the edges.
8. Use squeegee to remove all the bubbles :
   • Use small strokes.
   • Use squeegee tip at an angle vs. full blade flat on the surface.
   • First apply to the corners, then top and bottom of the sticker.
   • Wipe the surface with the microfiber towel for pre-inspection.
   • From an angle check for any bubbles.
   • Re-squeeze any bubbles to the size of a mosquito bite.
9. Repeat the same procedure for the Handle Piece.
10. Repeat the same procedure with the other pieces.
    • Pro Tip from ARMOR UP Installer :
    • Start with the ‘2nd-row rear passenger-side door’ for the Learning Curve effect.
    • Then the ‘front passenger-side door’.
    • Then the ‘rear driver-side door’.
    • You will thank me for this!
11. Wait for at least for 48 hours before washing the car.

FAQ

Q: Can I use tap water instead of distilled water for the installation process?
A: It is recommended to use distilled water for better results during installation to avoid any impurities that may affect the adhesion of the stickers.

Q: How long should I wait before washing my car after applying the ARMOR UP kit?
A: It is advised to wait at least 48 hours before washing your car to allow the stickers to properly adhere to the surface.

References

• Armor Up – Prodynamics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>