BARTEC Pixavi Cam Smartphone User Guide
- June 3, 2024
- BARTEC
Table of Contents
BARTEC Pixavi Cam Smartphone
Introduction
Congratulations on your Pixavi intrinsically safe device. All you need to get
started with Pixavi Phone, Pixavi Cam and Pixavi Thermal can be found in this
quick guide. If you need further assistance, try the AndroidTM help function,
or visit:
www.bartecmobility.com/support-portal
-
Pixavi Phone (¹)
Intrinsically safe smartphone -
Pixavi Thermal (²)
Intrinsically safe smartphone with FLIRTM thermal camera -
Pixavi Cam (³)
Intrinsicallty safe camera
Your device
FRONT
- 5.5” OLED
- Power button
- Volume button (-/+)
- Programmable button
- Proximity/Ambient light sensor and status LED 6: Front Camera
- Earpiece speaker
- Lanyard mounting slot
- Magnetic USB connector
- Microphone
BACK
- Loudspeaker
- Thermal camera (²)
- Main camera
- Flash
- Microphone
- Dual SIM/SD tray (¹, ²) or SD tray (³) (below battery pack)
- Battery pack
- Battery pack torx T10 fasteners
- NFC
Getting started
- Insert the SIM and/or SD card according to theSIM/SD-card instructions (separate sheet)
- Press and hold the Power button to power on the device
Charging
Insert the magnetic charger cable in the USB/Charging port at the bottom of the device. Make sure the orientation of the cable is as illustrated below.
Programmable button
The programmable button can be configured to launch an applications or action
on single tap, double tap and long press.
It’s comes preconfigured but can be changed based on your preferences. Go to
Setting -> Programmable Button.
Other options:
- Push-to-talk (PTT): Press and hold to talk. Single tap, duble tap and press and hold will be disabled when PTT is activated.
- SOS-message: Tap the button fast 5 times to send a SOS message to one or multiple contacts.
Troubleshooting and Support
If the device becomes unresponsive or does not boot successfully, try
performing a soft reset. This is done by pressing and holding the power button
down for 10 seconds.
FAQs and technical support can be found here: www.bartecmobility.com/support-
portal
Product marking
Audio Levels
The device is compliant with the EN9650-1 standard. However, third party music
players can exceed the recommended audio levels, and as such should be used
with caution as prolonged listening to sound at high volumes can cause
permanent damage.
Special Conditions For Safe Use
FCC/IC
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Specific Absorption Rate Data
The Pixavi Phone, Pixavi Thermal and Pixavi Cam is a radio transmitter and
receiver. It is designed and manufactured not to exceed the emission limits
for exposure to radio frequency (RF) energy set by the Federal Communications
Commission (FCC) of the U.S. Government, Industry Canada of the Canadian
Government (IC), and recommended by The Council of the European Union. The
exposure standard for wireless devices employs a unit of measurement known as
the Specific Absorption Rate, or SAR. The SAR limit set by the FCC/IC is
1.6W/kg. The SAR limit recommended by The Council of the European Union is
2.0W/kg. Tests for SAR are conducted using standard operating positions
specified by the FCC/IC with the device transmitting at its highest certi-fied
power level in all tested frequency bands. For body worn operation, the Pixavi
Phone, Pixavi Thermal and Pixavi Cam devices has been tested and meets the
FCC/IC exposure guidelines when used with an accessory that contains no metal
and that positions the device a minimum of 10 mm from the body. Such a device
can i.e. be BARTEC PIXAVI wrist cradle or BARTEC PIXAVI belt clip.
The highest SAR value measured for the Pixavi Phone, Pixavi Thermal and Pixavi
Cam is:
- Head SAR: 0.626 (W/kg)
- Body SAR: 1.202 (W/kg)
FCC
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This Pixavi Cam meets the government’s requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluations
of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health.
IC
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Conditions For Use (ATEX & IECEx)
The ambient temperature range of the device is -20°C to + 60°C. The device
shall be protected from contamination by liquid and dust; this is normally
achieved by the operator carrying the device on their person. The USB port may
be used for charging the equipment when in the non-hazardous area only.
For charging the device, use only Bartec approved chargers:
- Charger with EU plug: G7-S0Z0-0001
- Charger with UK plug: G7-S0Z0-0002
- Charger with US plug: G7-S0Z0-0003
- Charger with AU plug: G7-S0Z0-0004
- Charging dock: G7-S0Z0-0007
- Vehicle charging dock: G7-S0Z0-0008
For connection to computers and car chargers, use only Bartec-approved charging cable: USB Safe Box cable G7-S0Z0-0006
Conditions For Use (CSA)
The ambient temperature range of the device is -20°C to + 60°C. The device
shall be protected from contamination by liquid and dust; this is normally
achieved by the operator carrying the device on their person. The USB port may
be used for charging the equipment when in a non-hazardous area only.
For charging the device, use only Bartec-approved chargers:
- Charger with EU plug: G7-S0Z0-0001
- Charger with UK plug: G7-S0Z0-0002
- Charger with US plug: G7-S0Z0-0003
- Charger with AU plug: G7-S0Z0-0004
- Charging dock: G7-S0Z0-0007
- Vehicle charging dock: G7-S0Z0-0008
For connection to computers and car chargers, use only Bartec-approved charging cable: USB Safe Box cable G7-S0Z0-0006
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>