BARTEC 17-S13 Pixavi Phone User Guide
- June 12, 2024
- BARTEC
Table of Contents
Quick Start Guide
Product name:
Pixavi Phone
Pixavi Thermal
Pixavi Cam
Type: 17-S13*-1*/***
Introduction
Congratulations on your Pixavi intrinsically safe device.
All you need to get started with Pixavi Phone, Pixavi Cam and Pixavi Thermal
can be found in this quick guide. If you need further assistance, try the
Android TM help function, or visit: www.bartecmobility.com/support-
portal
Pixavi Phone (¹)
Intrinsically safe smartphone
Pixavi Thermal (²)
Intrinsically safe smartphone with FLIR TM thermal camera
Pixavi Cam(³)
Intrinsically safe camera
(¹-3) Used to identify the product variants in this quick guide
Warnings
Warnings are used in this quick guide to warn of risks of damage to property
and personal injuries. Always read and follow these warnings
DANGER:
designates a hazardous situation that can lead to death or serious, permanent
injuries if safety measures are disregarded.
ATTENTION:
designates a hazardous situation that can lead to material damage if safety
measures are disregarded.
Warranty
www.bartecmobility.com/warranty/pixavi
Your device
- : 5.5” OLED
- : Screen protector
- : Power button
- : Volume button (-/+)
- : Programmable button
- : Proximity/Ambient light sensor and status LED
- : Front Camera
- : Earpiece speaker
- : Lanyard mounting slot (remove battery pack for easy installation)
- : Magnetic USB connector
- : Microphone
Do not remove the screen protector! Replace with type: 17-S1Z0-0007 if damaged. Only replace the screen protector outside the hazardous area.
- : Loudspeaker
- : Thermal camera(²)
- : Main camera
- : Flash
- : Microphone
- : Dual SIM/SD tray(¹,²) or SD tray(³) (accessible behind battery pack)
- : Battery pack
- : Battery pack torx T10 fasteners
- : NFC
(¹) Pixavi Phone
(²) Pixavi Thermal
(³) Pixavi Cam
Getting started
Insert the SIM card and/or SD card and Battery pack according to the
instructions below.
The ejection tool can be found attached to the SIM/SD-card instructions sheet
(separate sheet)
1. Ensure that the ejection pin is perpendicular to the
hole. Otherwise, the device may be damaged.
2. Use only nano-SIM cards and/or Micro SD card. Pixavi Phone and Pixavi
Thermal supports 2x nano-SIM or 1x nano-SIM and 1x micro SD. Pixavi Cam
supports 1x micro SD.
3. If the card is not fixed firmly into the tray, the SIM/SD card may fall out
of the tray.
Only insert or remove the battery outside the potentially explosive atmosphere
Only use batteries that have been certified by BARTEC,
Type: 17-S1Z0-0001/****
Charging
Insert the magnetic charger cable in the USB/Charging port at the bottom of
the device. Make sure the orientation of the cable is as illustrated
below.
Do not use
any force when inserting the magnetic charging/USB cable.
The cable can only be inserted in the orientation illustrated above
The USB port shall only be used for charging the equipment when in the non-
hazardous area
For charging the device, use only Bartec approved chargers and cables
Power on your device
Press and hold the Power button to power on the device
Programmable button
The programmable button can be configured to launch an applications or action
on single tap, double tap and long press.
It comes preconfigured but can be changed based on your preferences. Go to
Settings -> Programmable Button. Other options:
Push-to-talk (PTT): Press and hold to talk.
Single tap, double tap and press and hold will be disabled when PTT is
activated.
SOS: Tap the button fast 5 times to send a SOS message to one or multiple
contacts.
Replacing battery pack
Make sure the device is turned off before
replacing the battery pack. 1 Loosen the two fasteners with the supplied Torx
T10 screwdriver (the fasteners are captive screws and not suppose to be fully
removed). 2 Remove the battery pack.
3 Replace the battery pack and tighten the fasteners.
Only insert or remove the battery outside the potentially explosive atmosphere
Only use batteries that have been certified by BARTEC,
Type: 17-S1Z0-0001/****
Troubleshooting and Support
If the device becomes unresponsive or does not boot successfully, try
performing a soft reset. This is done by pressing and holding the power button
for 10 seconds.
FAQs and technical support can be found here: www.bartecmobility.com/support-
portal
Storage
Battery storage information:
The batteries of BARTEC (type 17-S1Z0-0001/****) are developed and
manufactured in accordance with the highest industrial standards. The
operating time or storage period of a battery is restricted, however. The
actual life of a battery is influenced by different factors, e.g. hot, cold,
rough operating environment and physical damage.
Batteries kept for a duration of six months or longer should be charged,
discharged and charged again at least every three months. If electrolyte has
escaped, do not touch the areas affected and dispose of the batteries
properly. Replace the battery if the operating time has shortened
considerably.
The standard warranty period for all BARTEC batteries is six months, whereby
it is irrelevant whether the battery was acquired separately or was contained
in the scope of the delivery of the device.
Make sure the battery pack is charged minimum every three months
Protect the device from constant moisture
Cleaning
Do not use any chemical cleaning agents to clean the deivce.
Use a damp cloth.
Cleaning: only clean with a damp cloth
Product marking
Explosion
protection
ATEX Zone 1 / 21
Type| 17-S13*-1*/***
Marking| *II 2G Ex ib IIC T4 Gb
II 2D Ex ib IIIC T135°C Db
-20°C ≤ Ta ≤ +60°C
Test certificate| CSANe 20ATEX4223X
IECEx Zone 1 / 21
Type| 17-S13-1*/*****
Marking| Ex ib IIC T4 Gb
Ex ib IIIC T135°C Db
-20°C ≤ Ta ≤ +60°C
Test certificate| IECEx SIR 20.0036X
NEC 500/505
Type| 17-S13*-1*/***
Marking| Class I; Division 1; Groups A, B, C and D; T4
Ex ia IIC T4 Ga
Class I, Zone 0, AEx ia IIC T4 Ga
Test certificate| CSA 22CA80042090X
Temperature range
| ATEX/IECEx (EN IEC 60079-0) | -20 °C ≤ Ta ≤ +60 °C (-4 °F ≤ Ta ≤ 140 °F) |
|---|---|
| Discarge (EN IEC 62368-1) | -20 °C ≤ Ta ≤ +50 °C (-4 °F ≤ Ta ≤ 122 °F) |
| Charging (EN IEC 62368-1) | 0 °C ≤ Ta ≤ +45 °C (32 °F ≤ Ta ≤ 113 °F) |
| Long term storage | 0 °C ≤ Ta ≤ +35 °C (32 °F ≤ Ta ≤ 95 °F) |
EX port parameters
IEC Parameters| USA Parameters| USB (magnetic connector)| SIM (1&2) card| SD
card| Unit
---|---|---|---|---|---
U0| Voc| 5.45| 5.45| 5.45| V
lo| Isc| 2.81| 1.20| 7.04| A
Po| Pout| 0.84| 0.41| 2.59| W
Co| Ca| N/A| 27.40| 39.30| µF
Lo| La| N/A| 24.97| 0.72| µH
USB Ui and device Um (non-hazardous area connection only) = 12V.
Specific conditions for use
The USB port shall only be used for charging the equipment when in the non-
hazardous area.
Um (Charging / USB contacts) = 12V, this is ensured by using a charger type
G7-S0Z0-0001 – G7-S0Z0-0004 or other accessories specified by Bartec GmbH. The
ambient temperature during charging shall be in the range 0ºC to 45ºC.
The USB port is also used for data download. The port has been assessed with a
Um of 12 V and shall be installed in accordance with IEC 60079-14/EN 60079-14.
Care should be taken to avoid the risk of drop and impact during storage,
transportation and use as aluminium is present in the structure of the
enclosure.
The apparatus shall not be subjected to a prolific charge generating mechanism
(such as might occur in pneumatic transfer of powders or charge spraying in a
powder coating process).
Do not remove the battery pack in the hazardous location.
The battery pack surfaces shall at regular intervals be checked for wear and
tear by the user. Replace with type:
17-S1Z0-0001/** if damaged.
General safety requirements
Only use accessories that are approved by BARTEC In the case of malfunction or
damaged enclosure, remove the device immediately from the potentially
explosive atmosphere.
Specific Absorption Rate Data**
The Pixavi Phone, Pixavi Thermal and Pixavi Cam is a radio transmitter and
receiver. It is designed and manufactured not to exceed the emission limits
for exposure to radio frequency (RF) energy set by the Federal Communications
Commission (FCC) of the U.S. Government, Industry Canada of the Canadian
Government (IC), and recommended by the Council of the European Union. The
exposure standard for wireless devices employs a unit of measurement known as
the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC/IC is 1.6W/kg averaged over 1 gram of actual
tissue.
The SAR limit recommended by The Council of the European Union is 2.0W/kg
averaged over 10 g of actual tissue.
The SAR value measured for the Pixavi Phone, Pixavi Thermal and Pixavi Cam:
| FCC/ID | Pixavi Phone/Thermal | Head | 0.626 W/kg |
|---|---|---|---|
| FCC/ID | Pixavi Phone/Thermal | Body | 1.202 W/kg |
| FCC/ID | Pixavi Cam | Head | 0.571 W/kg |
| FCC/ID | Pixavi Cam | Body | 0.148 W/kg |
| CE | Pixavi Phone/Thermal | Head | 0.164 W/kg |
| CE | Pixavi Phone/Thermal | Body | 0.633 W/kg |
FCC/ISED
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This product meets the applicable Innovation, Science and Economic Development
Canada technical specifications.
Legal
Android is a trademark of Google LLC.
BARTEC GmbH
Max-Eyth-Str. 16
97980 Bad Mergentheim, Germany
Phone: +49 7931 597-0
info@bartec.com
11-S130-7E0001-Rev01-450631
Documents / Resources
|
BARTEC 17-S13 Pixavi
Phone
[pdf] User Guide
17-S13 Pixavi Phone, 17-S13, Pixavi Phone, Phone
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>