LEDone Indoor LED Strip Light, 8 foot, Multi-Watt, Multi-Color, Installation Guide
- June 3, 2024
- LEDone
Table of Contents
- LEDone Indoor LED Strip Light, 8 foot, Multi-Watt, Multi-Color,
- LOC Strip Light Series Installation Guide
- CAUTION: Risk of fire
- CLEANING & MAINTENANCE:
- TROUBLESHOOTING:
- 0-10V DIMMABLE WIRING:
- INSTALLATION OPTIONS:
- J-ADAPTOR
- 3. LINKING
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LEDone Indoor LED Strip Light, 8 foot, Multi-Watt, Multi-Color,
Installation Guide
LOC Strip Light Series Installation Guide
SAFETY INSTRUCTIONS: Read instructions carefully before attempting to install fixture.
- All wiring should be performed by a qualified electrician.
- Disconnect power before installing or servicing. This fixture must be wired in accordance with the National Electrical
Code and applicable local codes and ordinances.
CAUTION: Risk of fire
- WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
- WARNING: Suitable for 9/16 or 15/16 flat tee grid in both insulated ceilings and non-insulated ceilings.
- WARNING: Do NOT handle energized fixture when hands are wet, when standing on wet or damp surfaces or in water.
- WARNING: Vapor barrier must be suitable for 90°C.
- WARNING: Fixture to be independently supported to building structure.
CLEANING & MAINTENANCE:
CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.
- Clean glass lens with non-abrasive glass cleaning solution.
- Do NOT open fixture to clean the LED. Do NOT touch the LED.
Note: These instructions do not cover all details or variation in equipment, nor do they provide for every possible situation during installation, operation or maintenance.
TROUBLESHOOTING:
- Check that the line voltage at fixture is correct. Refer to wiring directions.
- Check that the fixture is grounded properly.
0-10V DIMMABLE WIRING:
Universal voltage driver permits operation at 120V through 347V, 50/60Hz.
0-10V control wires must be rated for 300V minimum. For 0-
10V dimming, follow the wiring directions in Fig. 1.
- Connect the BLACK fixture lead to the (+) LINE supply lead.
- Connect the WHITE fixture lead to the (-) COMMON supply lead
- Connect the GROUND wire from fixture to the supply ground. Do NOT connect the GROUND of the dimming fixture to the output.
- Connect the VIOLET fixture lead to the (V+) DIM lead.
- Connect the GRAY fixture lead to the (V-) DIM lead.
INSTALLATION OPTIONS:
CAUTION: Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply. CHAIN HANGER
- Mount chain to ceiling.
- Connect chain to V hanger as pictured below.
- Connect the wiring to the fixture.
Assemble the V hanger and chain as shown.
SURFACE MOUNT
- Open fixture and screw fixture base to mounting surface.
- Wire the fixture.
- Re-attach lens to close fixture
J-ADAPTOR
-
Place fixture on mounting surface.
-
Install J-adaptor on each side of the cable hole of fixture (Fig. 1)
-
Connect and complete (Fig. 2)
3. LINKING
-
Place 2 pieces of the strip lights together so that End A is next to End B. (Fig. 1)
-
Open the safety cover of End A and End B to show the female 5 pin. (Fig. 2)
-
Use the male 5 pin connecter to link End A to End B together. (Fig. 3)
-
Fix the connection with a H-bracket and screw. (Fig. 4)
Phone: (844) LEDONE6 | Fax: 1-510-217-9461 | Web: www.ledonecorp.com
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>