LEDone LOC-T52FT-12W50K-SGFD YM Type A+B Tub Installation Guide

LEDone LOC-T52FT-12W50K-SGFD YM Type A+B Tub

SAFETY INSTRUCTIONS

Read the instructions carefully before attempting to install the fixture.

• WARNING: You MUST check the ballast compatibility list before installing with ballast Type A.
• WARNING: Risk of fire or electric shock. LED tube installation requires knowledge of luminaire electrical systems. If not qualified, do NOT attempt installation. All wiring should be performed by a qualified electrician.
•   WARNING: Disconnect power before installing or servicing. This fixture must be wired in accordance with the National Electrical Code and applicable local codes and ordinances.
• WARNING: Make certain power is OFF before installing or maintaining the fixture. No user-serviceable parts inside.
• WARNING: ONLY compatible with LED One dimmer.
•   WARNING: Disconnect the power to avoid shock when the equipment is wet.
•   WARNING : Check the ballast compatibility list before installing this tube to the fixtures with electronic ballast. Do NOT install this kit to the fixture if the ballast is not on the list. If the ballast is not on the list, bypass the ballast or confirm with the supplier.
•   WARNING : If the tube is installed as Type B (bypass), the fixture will no longer operate fluorescent lamps.
•   WARNING: Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
• WARNING: Do NOT make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
•   WARNING: To prevent wiring damage or abrasion, do NOT expose wiring to edges of sheet metal or other sharp objects.
• WARNING: This LED tube is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction.

CLEANING & MAINTENANCE

CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.

1.  Clean the lens with a non-abrasive cleaning solution.
2.  Do NOT open the fixture to clean the LED. Do NOT touch the LED.

Note: These instructions do not cover all details or variations in equipment, nor do they provide for every possible situation during installation, operation or maintenance.

INSTALLATION TYPE A
You MUST check the ballast compatibility list before installing with ballast Type A.

LOC-T52FT-12W50K-SGFD YM Type A+B Installation Guide

1.  Disconnect the power of luminaire.
2.  Remove existing tube lamp(s).
   •  Remove the diffuser (if provided)
   •  Remove existing fluorescent lamp(s)
3.  Check the Ballast Compatibility list
4.  Install the LED tube(s).
   •  Read the label on the LED tube to ensure the power end of the LED is aligned with the powered tube socket. Then insert the LED lamp.
   • Replace the troffer lens, if present.
   • After the modification is completed, attach the replacement marking and cautionary label to a visible place on the luminaire and keep it visible after installation.
5.  Restore the power of the luminaire.

INSTALLATION TYPE B: Note: The tube can ONLY work with double-end power input.

1.  Disconnect the power of the luminaire.
2.  Remove existing tube lamp(s).
   •  Remove troffer (if present)
   •  Remove existing fluorescent lamp(s)
   •  Remove ballast cover (cover may be secured with screws or tabs)
3.  Install the LED tube(s).
   •  Read the label on the LED tube to ensure the power end of the LED is aligned with the powered tube socket. Then insert the LED lamp by sliding the pins into the sockets and rotating a quarter turn until the LED tube locks in place.
   •  Replace the troffer lens, if present.
   •  After the modification is completed, attach the replacement marking and cautionary label to a visible place on the luminaire and keep it visible after installation.
4. Restore the power of the luminaire.

DIMMING DIAGRAM

Warning: ONLY compatible with LED One dimmer.

Phone: (844) LEDONE6 | Fax: 1-510-217-9461 | Web: www.ledonecorp.com

References

• Energy Saving with LED Lighting Fixtures & Bulbs | LED One Corporation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>