RAZORRI MT04 Smart Meat Thermometer User Manual

RAZORRI MT04 Smart Meat Thermometer

Warnings

• Do not leave the probe in extremely hot foods or liquids (anything over 572°F/ 300°C) for more than one minute.
• Always wear heat-resistant gloves to use the probe. Do not touch the probe or wire with bare hands during or right after measuring temperature since it may be very hot.
• Do not use this device in a microwave oven.
• Do not place this device in a place where the temperature is too high. Please operate the device within the ambient temperature range of 32°F to 122°F(0°C to 50°C).
• Do not place the probe in the dishwasher or completely immerse it in any liquid. For cleaning, please wipe the probe tip with a damp soapy cloth or sponge and dry it.
• Do not use the device in the rain. The thermometer is not waterproof.
• Keep the probes and wires away from children. This device is not intended for use by persons under the age of 12.
• If this device is not in use for a long period of time, please remove its battery to prevent corrosion.

Specifications

Package Contents

Parts

⑬

|

Built-in Magnet

| To attach the device on the refrigerator or other metal surfaces.

⑭

|

Battery Lid

| To protect the batteries and the Temperature Alarm Button ⑮.

⑮

|

Temperature Alarm Button

| · Press to turn on/off the temperature alarm. Hold 3 seconds to switch the temperature unit

between Fahrenheit and Celsius.

⑯| Battery Compartment| To insert 3 batteries.

⑰

|

Probe Tip

| The tip for the probe, to sense the temperature of the foods.

Instructions of the Device

Note:

• Before using, please install the batteries (included) in the battery compartment of the device.
• When there is no operation on the buttons for 10 seconds, the backlight of the device will automatically turn off to enter Low Power Mode.

1. Power on/off
   Press and hold the Power/Set Button for 3 seconds.

2. Connect the probe to the device
   Plug the connection port of the probe jack to the device. The screen will display the current
   the temperature of the probe.

3. Switch the measurement unit
   Remove the battery compartment cover on the device. Hold the Temperature Alarm Button for 3 seconds until it beeps to switch the temperature unit between Fahrenheit and Celsius ( the default unit is Fahrenheit ).

4. Set the preset temperature

   • Press the Power/Set Button to enter the preset temperature setting.
   • Press the “+”/”-” Button to increase/decrease the value or hold the button to speed up the adjusting.
   • Press the Power/Set Button  to confirm the setting. Or wait for 10 seconds, the value will be automatically confirmed.

Note:
When the measured temperature reaches the preset temperature, the device will start beeping and the value display will keep flashing. Press any button on the device to stop the flashing and beeping.

Instruction of the App

App Installation & Connection
You can set and check the temperature with the SmartLife App. Please download it from the App Store for IOS or Google Play Store for Android. You can scan the QR code here:

1. Account registration and login
   Please register an account with a valid email address. After registration, check your inbox to get the verification code, then enter the code and set your password to log in.

2. Connect the device with your phone

   • Press and hold the Power/Set Button to turn on the device.
   • Enable the Bluetooth of your smartphone.
   • Turn on the SmartLife App on your phone . Tap “Add Device”→ “Auto Scan”, the device will pop up.
   • Tap “Go to add” and the connection will start to load.
   • Wait for the connection to succeed.

Note:

• When the device has connected with the App before, simply turn on the device and open the
• App on the phone so the device can reconnect to your phone.
• If you fail to connect the device with your phone, press and hold the “+” and “-” Button together for 3 seconds to make the device enter connecting mode.
• The device can only connect with one smartphone at a time. When connected, please place your router, mobile phone, and the device as close as possible.
• An account can only be logged in on one device at a time.
• Please use the App in a networked environment.
• The App is only compatible with smartphones, not tablets or PCs.

Using the SmartLife App

• Monitor the temperature After connecting the device, you can easily monitor the probe temperature on your phone.
• Preset the temperature

1. Tap “Set up the probe”. Select a type of meat and level of doneness.
2. Tap “Confirm” to save the setting.

Home Page

Note:
When the probe temperature reaches the preset temperature, the device will start beeping and a reminder will pop up on the phone.

Temperature Page

Clean and Maintenance

Cleaning

• Before using the device, clean the probe with a soapy sponge or cloth, then rinse and dry it.
• Always take your reading in the thickest part of the meat, avoiding the bones and heavy fat parts. Because the thin parts of the meat are difficult to measure, they tend to  cook faster, and if the tip touches the bone or heavy fat parts, or the probe tip is not inserted deep enough, it’s hard to ensure accuracy.
• When measuring different foods or meats with the same probe, please cool the probe down first by rinsing the tip with cold water.
• After using the device, you can sterilize the probe by inserting it in boiling water for several minutes.
• After using the device, hold the Power/Set Button for 3 seconds to turn it off for protecting the batteries.

Storage
After using the probes, you can use the included probe storage rack to store them.

1. Insert the stainless part of the probe into the storage rack’s slot and wrap the probe wire into the rack.
2. Press the connector of the probe into the rack.

• support@razorri.com
• www.razorri.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>