Breezary 32004 Ceiling Fan with Light User Manual
- June 16, 2024
- Breezary
Table of Contents
INSTALLATION & USER MANUAL
84INCH CEILING FAN WITH LIGHT 
ITEM #32004
Customer Service: support@breezary.com
Safety Information
READ AND SAVE THESE INSTRUCTIONS.
- To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin.
- All wiring must be in accordancce with the National Electrical Code “ANSI/NFPA 70” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
- Do not place objects in the path of the blades.
- To clean the fixture ,turn off the power, wait for itto cool, and wipe the fixture with a clean dry, soft cloth.
- After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment- grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
- All screws must be checked and retightened where necessary before installation.
WARNING: To reduce the risk of electrical shock or fire, not use this fan
with any solid-state fan speed control device. It will permanently damage the
electronic circuitry.
WARNING: To reduce the risk of fire or injury do not use this product in
conjunction with any variable (heostat) wall control.
WARNING: To reduce the risk of personal injury, do not bend the blade
brackets when installing the rackets balancing the blades, or cleaning the
fan. Do not insert objects.
WARNING: To avoid possible electrical shock, turn the electricity off at
the main fuse box before wiring.
WARNING: To reduce the risk of electrical shock, this must be installed
with an isolating wall control / switch.
CAUTION: Please use carefully when working around or cleaning the fan to
avoid injury or damage of fan.
CAUTION: The fan must be mounted with a approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
CAUTION: Changes or modifications not expressly minimum of 7.5 ft (2.3 m)
clearance from the trailing edge of the blades to the floor.
Dimension Reference
Hardware Included
Hardware Package………………………….. Quantity
S1.Expansion Screw ………………………….2
S2.Spring Washer ………………………….4
S3.Wood Screw………………………….4
S4.Blade Screw ………………………….25
S5.Wire Connector ………………………….3
S6.Balance Kit ………………………….1
Fan Parts Included
Item name …………………………….Quantity
1.Remote Control…………………….1
2.Mounting Bracket………………….1
3.Canopy……………………………1
4.Canopy Cover……………………………1
5.Yoke Cover……………………………1
6.Downrod……………………………1
7.Long Downrod……………………………1
8.Motor Housing……………………………1
9.Lamp Housing and LED……………..1
10.Lamp Shade……………………………1
11.Blade……………………………8
Exploded View
Installation Instructions
Step1 MOUNTING
– Take out fan downrod.
– Remove cotter pin and bolt from downrod.
– Take out fan motor housing.
– Loosen jam screw in yoke until it is flush with the inside surface.
– Place the downrod inside the canopy, canopy cover, and yoke cover.
– Route wires exiting motor through yoke cover, canopy and downrod.
– Insert bolt through hole in and downrod. Be careful notto damage or cut the
fan wires.
– Tighten bolt. Secure with cotter pin through hole in the end of the bolt.
– Secure downrod in position by tightening jam screws.
– Slide yoke cover down and it will flush with the motor housing.
CAUTION: To ensure wobble-free operation and to avoid damage to the fan,
the downrod and the set crew must be completely tightened. 
Step2 INSTALL MOUNTING BRACKET
WARNING: |n order to avoid the risk of dropping, this product is only
installed on concrete ceilings or strong wood!
– Lift the fan motor assembly into position, and place the hanger ball into
the mounting bracket. Rotate the downrod until the check groove drops into the
registration slot and seats firmly. The downrod should not rotate if this is
done correctly.
Step3 Attaching the Fan Blades.
– Attach the blade to the motor with blade screws and washer.
– Repeat this step for each blade assembly.
CAUTION:When installing the fan, fix the ceiling fan motor on the ceiling
before installing the ceiling fan blade
Step4 Assembling the lamp housing
– Feed the wire through the center hole of the lamp housing.
– Fix the lamp housing with screws.
– Connectthe plugs from the motorand LED.
Step5 The lampshade installation
– Install the lampshade to the lamp housing by turning clockwise to lock it
into place.
Step6 The receiver installation
– Put the receiver in the Mounting Bracket.
Step7 Wiring the Fan
– Wiring according to the wiring diagram.
Step8 Attaching the Canopy and Canopy cover
– Slide the canopy up to the ceiling and attach it to the Mounting Bracket
with the screws provided. Tighten all screws securely.
– Move the Canopy cover onto the canopy. (the decorative cover comes with
magnetism) 
CONGRATULATIONS!
YOU HAVE COMPLETED THE INSTALLATION
OPERATION
FUNCTION INSTRUCTION OF EMITTER
– Open battery cover on the hand-held remote and Install two 1.5V AAA
batteries,
– If the emitter can not control the fan
- When the emitter cannot control the receiver, please check is there any existence of similar remote controlled products nearby, then check whether they works, because remote controlled product with the same frequency will disturb each other.
- When the emitter cannot control the receiver,please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power.
- Turn on the power switch,Press and hold the Learning process button for 3 seconds within 10 seconds of power on. If you hear a beep sound,the pairingprocess is complete
– When installing the fan, the fan ceiling cover don’t press the antenna(or other wire), itis easy to breakdown the wire and short-circuited.
– Pressing the timer button will activate the timer function.The fan will automatically turn fan andlight (if light is on)off after 1,4 or 8 hours.
CAUTION: Do not use with a wall light dimmer switch.
NOTE: The battery will weaken with age and should be replaced before
leaking takes place as this will damage the remote control. dispose of used
battery properly and keep the battery out of the reach of children. 
- All off
- Fan off
- Light on
- Reverse function
- Fan speed
- Light off
- Learning process
- Timer
Troubleshooting Guide
If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly, installation, or wiring. In some cases these installation errors may be mistaken for defects. If you experience any faults please check this troubleshooting guide.
Troubleshooting Guide
If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly, installation, or wiring. In some cases these installation errors may be mistaken for defects. If you experience any faults please check this troubleshooting guide.
| Problem| Suggested Remedy
---|---|---
1| If fan does not work.| Check the main and branch circuit fuses or breakers.
Check the line wire connections to the fan and switch wire connections in the
switch housing.
Check the battery in the remote control.
2| If fan sounds noisy.| Ensure all motor housing screws are snug.
Ensure the screws that attach the fan blade bracket to the motor hub are
tight.
Ensure the wire nut connections are not rattling against each other or the
interior wall of the switch housing.
Observe whether the noise decreases after the fan has been running for 24
hours.
Newly installed fans may have noise issues
If you are using the Ceiling Fan light kit, ensure the screws securing the
glassware are tight. Check that the light bulbs are also secure.
Ensure the canopy is a short distance from the ceiling. It should not touch
the ceiling.
Ensure your outlet box is secure and rubber isolator pads were used between
the mounting plate and outlet box.
3| If fan wobbles.| Check that all blades are screwed firmly into blade
holders.
Check that all blade holders are tightened securely to motor.
Make sure that canopy and mounting bracket are tightened securely to ceiling
junction box and junction box is mounted firmly to ceiling joist.
Most fan wobble problems are caused when blade levels are unequal.
Check this level by selecting a point on the ceiling above the tip of one of
the blades keeping measure within 1/8 in. Rotate the fan until the next blade
is positioned for measurement. Repeat for each blade. If all blade
levels are not equal you can adjust blade levels by the following procedure.
To adjust a blade tip down insert a washer(not supplied)between the blade and
blade holder at the screw closest to the motor. To adjust a blade tip up
insert washer(not supplied)between the blade and blade holder at the two
screws farthest from the motor.
If blade wobble is still noticeable interchanging two adjacent (side by
side)blades can redistribute the weight and possibly result in smoother
operation.
4| If light does not work| Check blue wire from fan to make sure it is
connected to hot wire from the house.
Check for loose or disconnected wires in fan switch housing.
Check for loose or disconnected wires in light kit.
Check for faulty light bulbs. CAUTION: Make sure main power is turned off
before entering switch housing.
If the fan light shuts off shortly after being switched on it may be due to
excessive current demand. Turn off power to the fan and replace the light
bulbs with lower wattage bulbs. Turn on power to the fan using the pull chain,
wall switch, or remote control (whichever is installed on the particular fan).
Balancing Kit
The Balancing kit should only be used if there is an unacceptable amount of fan wobble after completing all the steps in your Owners Manual under “Attaching The Fan Blades.”
- Turn the fan on and set the speed control setting to a speed at which the wobbles is the greatest.
- Turn off the fan and allow it to a come to ¢ complete stop. Select one blade and place the balance clip on it, halfway between the blade holder and the blade tip on the trailing edge of blade.
- Turn the fan on. Note whether the wobble has increased or decreased. Turn the fan off, move the clip to another blade, and retest. Repeal this procedure on all blades noting the blade on which the greatest improvement is achieved.
- Move the clip back to the blade that showed the greatest improvement. Move the clip inward and outward on this blade and operate the fan to find the position where the clip gives the greatest improvement
- Remove the clip and install a balancing weight to the top of blade along the center line near the point where the clip was positioned.
- If the fan wobble problem has not been corrected you can try to improve the balancing further by using the balancing clip and additional weights
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>