SW-MOTECH HTA.19.806.10000 SLC Side Pannier Holder Instruction Manual

ANBAUANLEITUNG
mounting instructions
BC.SYS.19.806.30000/B
contiene
HTA.19.806.10000
HTA.19.806.11000
SYS.00.002.10000L/B
SYS.00.002.10000R/B
BC.SYS.00.002.10000 

MOUNTING INSTRUCTIONS

Revision: 00
Datum / Date: 03 – 2021
SIC side carrier
Thank you for choosing this premium product from SW-MOTECH Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications) are also available for download at our webshop.
Installation and/Or maintenance of this product require good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration/ operation as well as TOV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer’s specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK, After installation makes sure that all parts and connections previously removed are properly replaced. Also, make sure that no moving pans are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

Packed by:
Date of packaging:

SW-MOTECH GmbH & Co. KG
Ernteweg 7-10
35282 Rauschenberg
Germany| Tel. / phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
www.sw-motech.com 
---|---

Copyright by
SW-MOTECH GmbH & Co. KG
Technical and design modifications are subject to change.

PARTS LIST

Note: a All measurements in millimeters. b The second number indicates the total quantity of the part in the delivery. C No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING

NOTE: The following mounting steps show the mounting of the left side carrier. Mount the right side carrier in the same way. Attach the parts (2) to (5) to the side carrier (1). ATTENTION: Use a liquid thread locker! Tighten the screws as specified.

Remove the original screws and spacers from the two upper mounting points of the vehicle. Attach the side carrier (1) behind the passenger footrest mount and to the rear of the vehicle, as shown.
ATTENTION: Use liquid thread locker! Once all parts are aligned without excess tension, tighten the screws as specified.

MOUNTING INSTRUCTIONS

Art.-Nr. / Item No.: SYS.00.002.10000*/B
Revision: 02 • Datum / Date: 10 – 2018
Adapter plate for SysBag 15

 Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Installation and/or maintenance of this product require good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country: specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer’s specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK : After installation makes sure that all parts and connections previously removed are properly replaced. Also, make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

Date of packaging:

| (7)| SYS.00.001.003| Countersunk Spacer| 4/4|
(8)| SYS.00.001.002| Sleeve Nut| 4/4|
| | | |
| | | |
1| (1)| .00.002. 10000L/B SYS.00.002.001| Adapter Plate for SysBag 15 left Adapter Plate| 1 /1|
| (2)| HTA.00.864.500.05| Locking Mechanism| 1 /1|
(3)| HTA.00.864.011| Locking Adapter| 2 /2|
(4)| M5 x 16; ISO 7380| Lionshead Screws; black| 12 /12| 3
(5)| M5; DIN 985| Lock Nut| 12/12|
| | | |
2| (6)| M8 x 16; DIN 7991| Countersunk Screw| 4/4| 15
| (7)| SYS.00.001.003| Countersunk Spacer| 4/4|
(8)| SYS.00.001.002| Sleeve Nut| 4/4|
| | | |
| | | | |

• AR measurements in millimeters. • ** The second number indicates the total quantity of the part in the delivery. *** No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

Configuration A for:
PRO side carrier NOTE: The mounting steps (11 to (3.1 show the mounting of the left adapter plate. Mount the right adapter plate in the same way as on the left side. Mount the shown parts on the other side of the adapter plate. ATTENTION: Pay attention to the markings (parallelogram or triangle) which define the respective mounting side (see detail drawing on the top right side)! Attach the parts (2) to (5) to the adapter plate (1). as shown in the drawing. Tighten the screws as specified in the parts list.

Configuration B for:
Adapter plate for STEEL-RACK and ADVENTURE-RACK ATTENTION: Make sure that the locking mechanism (2) and the lock bolt of the adapter kit for SysBag 15/30 are mounted opposite to each other! Attach parts 121 to (5) to the adapter plate la as shown in the drawing. Tighten the screws as specified in the parts list.

Configuration C for:
SLC side carrier and Adapter plate for STREET-RACK NOTE: The mounting steps (11 to I.31 show the mounting of the left adapter plate. Mount the right adapter plate in the same way as on the left side. Mount the shown parts on the other side of the adapter plate.
ATTENTION: Pay attention to the markings (parallelogram or triangle) which define the respective mounting side (see detail drawing on the top right side)! Attach the parts (2) to (5) to the adapter plate (1). as shown in the drawing. Tighten the screws as specified in the parts list.

Attach the adapter plate (1) to your SysBag 15, as shown in the drawing. Pay attention to the alignment of the lid of the SysBag 15.
ATTENTION: Use a medium-strength liquid thread locker! Tighten the screws as specified in the parts list.

Attach the adapter plate (1) to your SysBag 15, as shown in the drawing. Pay attention to the alignment of the lid of the SysBag 15.
ATTENTION: Use a medium-strength liquid thread locker! Tighten the screws as specified in the parts list.

Place the locking openings of the locking mechanism (2) and the locking adapter (31 onto the guide bolts of the adapter kit for SysBag 15/30 (sold separately!. Then press the SysBag 15 onto the guide bolts, until it properly rests on your SW-MOTECH carrier system.
ATTENTION: Make sure that all guide bolts of the adapter kit for SysBag 15/30 engage at the same time! Pay attention to the clearly audible snap sound of the locking mechanism and that the red marking under the slider is not visible! To release press the slider downward or pull the release cord.

Art -Nr / Item No.: siehe Stiickliste / see parts list
Revision: 03 • Datum / Date: 11 – 2018
SysBag 10 / 15 / 30

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required le.g. ABE certifications), are also available for download at our webshop. Installation and/or maintenance of this product require good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts le.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country: specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items on the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you
FUNCTION CHECK : This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type. After fixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.

PRODUCT SPECIFIC INFORMATION ATTENTION: Riding with this product may affect the motorcycles driving and braking performance!
ATTENTION: Depending on the location of fixation, cornering and ground clearance can be reduced by using this product!
ATTENTION: Before riding and at each stop (every 200 km) check proper fixation of the product!

1 0 KG (22 (Ps) per SysBag 30

ATTENTION: The maximum vehicle load specified by the manufacturer and the maximum load of the SW-MOTECH carrier/rack must not be exceeded!
ATTENTION
NOT FOR OFFROAD USE! tikt SLU-MOTECH SW-MOTECH GmbH & Co. KG Ernteweg 8/10 35282 Rauschenberg Germany
Tel / phone + 49 (0)6425 / 8168 – 050 Fax / fax + 4910)6425 / 8168 – 10
infolasw-motech.com
www.sw-motech.com

| No.| No. / Description “| Part.| Anzahl**| N.m ***
---|---|---|---|---|---
| | BC.SYS.00.001.10000| SysBag 10| |
1| (1)| BC.SYS.00.001.10000| SysBag 10| 1/1|
| (2)| BC.ZUB.00.004.30000| Lashing Eye Set (2 pieces)| 1/1|
3| (3)| BC.ZUB.00.094.30000| Waterproof Innerbag| 1/1|
| | | | |
| BC.SYS.00.002.10000| SysBag 15| |
1| (1)|  BC.SYS.00.002.10000| SysBag 15| 1/1|
| (2)| BC.ZUB.00.004.30000| Lashing Eye Set (2 pieces)| 1 /1|
3| (3)| BC.ZUB.00.095.30000| Waterproof Innerbag| 1 /1|
| | | | |
| | | |
| Li YS.00.003.10000| SysBag 30| |
1| (1)| BC.SYS.00.003.10000| SysBag 30| 1 /1|
3| (2)| BC.ZUB.00.096.30000| Waterproof Innerbag| 1 /1|
| | | | |
| | | |
| | all SysBags| |
| (4)| SYS.00.001.004| Rubber Plug| 4/4|
| (5)| LSF.350.250| Adhesive Protection Foil| 1 /1|
(6)| BC.ZUB.00.097.30000| Loop Strap Set [4 pieces)| 1 /1|
(7)| BC.ZUB.00.098.30000| Shoulder Strap| 1 /1|
| | | |

• All measurements in millimeters.
  **The second number indicates the total quantity of the part in the delivery.
  * No torque specifications: Use the torque defined by the vehicle manufacturer!** The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

FASTENING

FASTENING TO THE VEHICLE ATTENTION:
Before fastening your SysBag (1) to the vehicle, the rear eyelets must be closed with the included rubber plugs (4) (shown in the detailed drawing at the topl!
ATTENTION: Protect sensitive surfaces in the area of the SysBag (1) and the fastening straps with the adhesive protection foil (5) from scratches! Place your SysBag (1) in the rear area of your vehicle [e.g. passenger seat, luggage rack, etc.). On both sides entangle TWO loop straps (6) to appropriate and reliable attachment points in the rear area of the vehicle [e.g. luggage hook etc.).
TIP: SW-MOTECH recommends the mounting with the lashing eyes 121 (only SysBag 10 and 15). Attach the lashing eyes (2) with the original screws behind your license plate. Then entangle on both sides TWO loop straps [6) to appropriate and reliable attachment points of the vehicle [e.g. vehicles frame, footrest mounts etc.). Attach the hook buckles of the loop straps (6) on both sides to the marked loops of the SysBag [11, as shown in the lower drawing. Tighten all loop straps until the SysBag (1) is centered and securely fastened to the vehicle. Secure the overlength of the loop straps (6) with the rubber loops.

FASTENING TO THE SYSBAG 15 (Optional)
Attach your SysBag 15 (A) to the vehicle as described in step (1). Loosen the upper two straps of the vehicle-mounted SysBag 15 (A). Attach the hook buckles of the two straps to the shown loops (behind the lid) of the SysBag 10 or 15 (B). On both sides, loosen the upper straps on each side of the SysBag 10/15 (131. Attach the hook buckles of the two straps to the loops shown on the attached SysBag 15 (A). After ALL FOUR hook buckles are properly hooked, tighten the straps until the SysBag 10/15 (B) is firmly attached on the SysBag 15 IA). Secure the overlength of the straps (4) with the velcro loops against flapping.
FUNCTION CHECK (MUST BE OBSERVED) ATTENTION:
All components of the SysBag must not contact any hot or moving parts of the vehicle. All parts should also remain 15 cm away from hot parts of the vehicle and remain clear of the exhaust stream. For this reason, compress the suspension fully several times with your vehicle stationary.

LOADING and CARE

ATTENTION: Always use the included waterproof inner bag (31 to protect your luggage from moisture! Fasten the waterproof inner bag (31 on the inside of the reinforced opening of the SysBag (11. Now roll the reinforced opening three times. Then close the SysBag (1) with the buckles.

ATTENTION: Make sure weight is evenly distributed between the left and right SysBag. Make sure that the banding is secured against shifting during the ride!
LOADING ATTENTION: Pay attention to keep items and electronic devices that can be damaged by magnetic fields away from the magnets sewn in the lid of the SysBag (11! ATTENTION: Never store pointy or sharp-edged objects, which could cause injury to persons or damage to the vehicle/side case!

ATTENTION: Surface materials can experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for this.
CARE
For cleaning use ONLY a soft textile brush, cloth or sponge and warm soapy water! Rinse with clean water. Do NOT use strong cleaning agents, rough cleaning tools or high pressure washer! Clean the SysBag after riding in salty conditions, to avoid damage from salt.

COMBINATIONS

The Syslog line has only three bags but offers over 20 mounting options and combination possibilities. The bags can be lashed to the tail end or at the side, as described in the mounting instructions, or mounted to the carrier/rack with a quick-release fastener. On this page, you will find some mounting examples. Vehicle-specific solutions, SysBag sets and adapter plates for SW-MOTECH carriers/racks can be found in our webshop.

Copyright by SW-MOTECH GmbH & Co. KG
Errors and omissions are expected. Technical and design modifications are subject to change.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>