TAKSTAR E10W Wireless Amplifier User Manual

: September 26, 2024
: TAKSTAR

Table of Contents

TAKSTAR E10W Wireless Amplifier
Product Usage Instructions
FAQ
Preface
Features
Applications
Package Contents
Specifications
Headset Microphone
Function Descriptions
Operating Instructions
Safety Instructions
Label Meanings
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TAKSTAR E10W Wireless Amplifier

Specifications

Model: E10W
Power Output: 0dB=1V/Paat 1KHz
Wireless Technology: Type-C USB
Frequency Range: 40Hz – 20kHz
Power Source: USB-C charging cable

Product Usage Instructions

Powering On and Adjusting Volume

To power on the amplifier, slide the Power Switch knob to the ON position. Adjust the knob towards ON to increase the volume and towards OFF to decrease it.

Indicator Light

The indicator light displays different states: solid blue when fully charged, flashing red and blue for low battery, solid red while charging, flashing blue during pairing search, and slow flashing blue if successfully paired.

M Mode Switch Button

Press this button to switch between different operating modes.
Long-press it with a USB drive and mic inserted to enter recording mode. Long-press again to exit recording mode and playback recorded content.

USB Port

Insert a USB drive with MP3 or WAV files for playback. Avoid using other file types. Use the USB-C charging cable for charging.

Wireless Headset Microphone Usage

Slide the Power Switch to ON to power the microphone. Use the Charging Port for charging.
Press the M Channel Switch to adjust frequency, tap + to increase volume, and tap – to decrease volume. Use LED Display to monitor channel, volume, and power mode.

FAQ

Q: How do I know if the amplifier is fully charged?

A: The indicator light will show a solid blue color when the amplifier is fully charged.

Q: Can I use file formats other than MP3 or WAV with the USB port?

A: It is recommended to only use MP3 or WAV files to prevent recognition issues or device damage.

Preface

Dear Customer,

Thank you for purchasing the Takstar E10W Wireless Amplifier. To better understand and use the product, please read this manual thoroughly. If you have any questions or suggestions, please contact our local sales outlet.

Features

Sleek, unique, modern, and lightweight design.
10W peak audio output with the rare-earth speaker.
Digital amplification for high-fidelity, noise-free sound.
Wireless connectivity for portable playback.
USB port for MP3 and audio file playback.
Status indicator light for real-time status updates.
MCU-controlled safe charging with overcharge protection.
Built-in 2500mAh lithium-ion battery for extended use.
UHF wireless up to 40m range in clear open environments.
Wireless headset mic with auto-pairing for easy use.
The headset’s high/low power modes adapt to different use cases.

Applications

Teaching, tour guiding, training, and promotions.

Package Contents

1 × Voice Amplifier
1 × Wireless Headset Microphone
1 × Type-C Charging Cable
1 × Shoulder Strap
1 × User Manual

Specifications

Voice Amplifier

Frequency Response: 80Hz-12kHz
Rated Power: 5W
Peak Power: 10W
Speaker Impedance: 4Ω
Operating Voltage: DC 3.7V-4.2V
Battery Spec: 18650 3.7V=2500mAh
Charging Spec: 5V=1A
Charging Port: USB-C
Charging Time: Approx. 2.5h
Battery Life: Approx. 23h
Wireless Connection: V5.3
Dimensions: 105mm×100mm×36mm
Weight: Approx. 170g
UHF Frequency: 630MHz – 698MHz (segmented)
UHF Operating Range: Approx. 40m in unobstructed, interference-free areas

Headset Microphone

Transducer: Back Electret Condenser
Polar Pattern: Unidirectional
Frequency Response: 60Hz-16kHz
Sensitivity: -50±3dB (0dB=1V/Pa, at 1kHz)
UHF Frequency: 630MHz-698MHz (segmented)
UHF Operating Range: Approx. 40m in unobstructed, interference-free areas
Battery Type: Li-ion
Battery Capacity: 3.7V / 400mA
Charging: DC 5V / 200mA
Charging Time: Approx. 2h
Battery Life: Approx. 5h
Product Weight: Approx. 39g
Note: The above data are measured by Takstar laboratory which has the final interpretation right!

Function Descriptions

Power Switch: Slide the knob to turn the amplifier on (“ON” position) or off (“OFF” position). Adjust the knob towards “ON” to increase the volume and towards “OFF” to decrease the volume.
Indicator Light: The indicator light shows different states: Solid blue when fully charged. Flashing red and blue if low battery. Solid red while charging. Flashing rapid blue during wireless pairing search, and slow flashing blue if successful paired.
M” Mode Switch Button: Press this button to switch between different operating modes. Voice prompts will accompany the mode changes. (Long-press this button when a USB drive and mic are inserted to enter recording mode. Long-press again to exit recording mode and automatically play back the recorded content.)
USB Port: Insert a USB drive with MP3 or WAV audio files to play them back. Avoid using other file types to prevent recognition issues or potential device damage.
MIC Jack: Insert a Ø3.5mm wired mic for voice amplification.
USB-C Charging Port: Connect the amplifier to a power adapter using the USB-C charging cable for charging.
Clip: Used to attach a shoulder strap, allowing the amplifier to be worn diagonally over the shoulder.

Wireless Headset Microphone

Power Switch: Slide to “ON” to power on, and “OFF” to power off.
Charging Port: Plug in the USB-C charging cable, the other end of the USB power source, to charge.
M Channel Switch: Press to adjust frequency, see “Pairing Method” section.
+ Button: Tap to increase mic volume; In pairing mode, tap to switch up channels, and hold to quick jump.
– Button: Tap to decrease mic volume; In pairing mode, tap to switch down channels, hold to quick-jump.
Indicator Light: Off when powered off and not charging; Solid blue when on; Solid blue when sufficient power; Flashing blue when low power; Solid red when charging, turns off when fully charged.
LED Display: Shows current channel, mic volume level, and power mode.
Channel/Volume Display: Default shows current channel (01-40); When adjusting volume, shows a level (U1-U9) for 3 seconds before reverting; Display turns off after 10 seconds of inactivity.
High/Low Power Mode: Press “M” and “-” for low power (E0); Press “M” and “+” for high power (E1). The low is about 10m range, and the high is about 40m.

Operating Instructions

Frequency Pairing

The product is pre-paired at the factory, so it will automatically connect when powered on, no need to pair. If there is signal interference, you can repair or change the frequency as follows.

Pairing Method
Ensure the headset mic and amplifier are both powered off. Turn on the headset mic, then long press the “M” button for 3 seconds until the display starts cycling. Immediately turn on the amplifier power. Wait for the mic display to stop cycling and show a static value. Speaking into the mic should produce sound, indicating a successful pairing. If the mic enters pairing mode but the amplifier is not turned on within 10 seconds, the pairing will fail.
If there is no sound when speaking into the headset mic, the pairing is unsuccessful. Please repeat the above pairing steps.
Frequency Changing Method
- With the amplifier and headset mic powered on and successfully paired, briefly press the “M” button on the headset mic to enter frequency-changing mode. The display will start flashing. Tap the “+” or “-” volume buttons to switch up or down channels.
- Or long press to quickly jump between channels. Press the “M” button again to confirm the selected frequency. If no button is pressed for 3 seconds, the frequency will stop flashing and be locked in.
Using Multiple Units
After pairing multiple units using the above “Pairing Method”, use the “Frequency Changing Method” to set each unit to a different channel.
When using multiple units simultaneously, change them to different channels to avoid interference.

Wireless Playback Pairing

To pair and connect the device with your phone or other wireless playback device, follow these steps.

Turn on the power switch of the amplifier. Press the “M” button to switch to the wireless playback mode. The indicator light will rapidly flash blue, indicating it is in search and pairing mode.
On your phone, access the “Settings” menu and enable the wireless playback function. Search for “TAKSTAR E10W” and connect to it. A voice prompt will confirm the successful wireless playback connection.
Next time you power on the device and select the wireless playback mode, if it has been previously paired, it will automatically reconnect to the last used playback device.

Safety Instructions

To avoid electric shock, overheating, fire, radiation, explosion, mechanical risk, and injury or property loss due to improper use, please read and observe the following items before use.

Please check if the power of the connected equipment matches with that of this product before operation. Adjust the volume to the proper level during operation.
- Do not operate at over-power or high-volume levels for extended time to avoid product malfunction.
If there is any abnormality during use (e.g., smoke, strange odor), please kill the power switch and unplug from the power source, then send the product to the local after-sales service for repair.
Power adapter used, if any, should be approved by CCC certification or similar standards and comply with the power supply requirements.
Keep this product and its accessories in a dry and ventilated area. Do not store in a humid or dusty area for an extended time.
- Keep away from fire, rain, liquid intrusion, bumping, throwing, vibrating, or blocking any ventilation openings, to prevent malfunction.
The product must, when installed on walls or ceilings, be fixed firmly in place at adequate strength to prevent falling.
Please abide by safety rules during operation. Do not use the product in places prohibited by laws or regulations to avoid accidents.
Do not disassemble or repair the product by yourself to avoid injury. If you have any questions or require any services, please contact our local after-sales service.

Label Meanings

This symbol indicates that this product should not be disposed of with your household waste, according to the WEEE directive (2012/19/EU) and your national law.
This product should be handed over to an authorized collection site for recycling waste electrical and electronic equipment (WEEE). Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with WEEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources.
For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, or your household waste disposal service.

About This Manual

This manual contains up-to-date technical specifications as of printing. However, specifications contained herein may not conform to your particular product since Takstar is constantly improving its products.
Also, specifications, devices, or accessories available may vary from region to region. If you have any questions, please contact our local sales outlet. For the latest version/more information, please visit our website: https://www.takstar.com/
Copyright ©2024 TAKSTAR. TAKSTAR and their respective logos are registered trademarks or trademarks of Guangdong Takstar Electronic Co., Ltd. in the PRC, and/or other countries. All other trademarks are the property of their respective owners.

Scan for more product information