MokerLink Commercial Series Switches User Manual

June 3, 2024
MokerLink

Commercial Series Switches

Quick Start Manual

MokerLink Commercial Series Switches A01

http://www.mokerlink.com   support@mokerlink.com

For more detailed information, please go to the website to download the operation manual

1 Description

  • The products described in this manual, including but not limited to the illustrated products, please refer to the actual product purchased. If any changes on product appearance, please refer to the official product information
  • Management switch connect and login methods are basically the same, this manual only introduces one of them
  • PoE switch and ethernet switch installation methods are the same, the actual use environment and method that depends on the specific product requirement
2 Packing List

  • Switch(Specific model See the product label for more details)
  • Power Cable(The default is pluggable or a power cable with built-in power module)
  • Power Adapter(Use for some external power products)
  • Console Cable, Configurable Disc(Use for managed products)
  • Brackets, Screw(Rack type standard, desktop type optional)
  • User manual, Certification
3 Installation Precautions

  • Do not install the equipment in the environment of seepage, drip or condensation easily, otherwise the equipment might burn out
  • Please ensure the environment where the equipment is installed is well ventilated, and forbidden to block the cooling holes
  • Do not install the equipment in a high density dust environment
  • If rack switches are in a natural heat dissipation environment, please ensure the separation distance exceeds 1U
  • Do not aerial cabling outdoor, otherwise the equipment is prone to lightning strike
  • Using temperature and humidity depend on the descriptions of the specific product
4 Safety Precautions

  • Do not look directly at the optical port to prevent the laser beam from burning your eyes
  • Do not install the power cord with power on to avoid personal injury
  • Do not supply power before equipment installation and wiring
  • ESD protection is necessary during the installation and maintenance of equipment
  • Do not place objects on the device
5 Switch Installation

Switches support a variety of installation methods, desktop, wall mounted, rack mount, please install according to the actual environmental requirements

Mounting Ear Installation

  5/8 Port

|

16/24 Port

|

Wall Mounted

|

1U Rack

---|---|---|---

Rack Mount Installation

MokerLink Commercial Series Switches A06

  1. Install 4 floating screws on the front hole bar of the cabinet, 2 on each side
  2. Load the equipment into the cabinet
  3. Use M6 screws to secure the equipment with the cabinet/rack
  4. Install earth wire to earth connection point
6 Connecting Equipment

Network Cable

  1. When the RJ45 port is on 2.5GE rate, use Cat5E and above network cable
  2. When the RJ45 port is on 5GE rate, a shielded network cable of Cat5E and above specifications is required, the unshielded network cable is not recommended
  3. When the RJ45 port is on lOGE rate, shielded network cable of Cat6A and above specifications is required

Grounding
Ensure that the grounding screw of the equipment is effectively grounded to protect the safety of the equipment

Optical Fiber

  1. Optical fibers must be used with the optical modules
  2. Fiber bending radius must not be less than 40 mm

Power Cable

  1. Distance between power cable and nework cable shoule be more than 10cm
  2. The AC power please use the local AC power cable
  3. The DC power please pay attention to the positive and negative electrodes

Console, USB

  1. Some switches provide USB interfaces for uploading and downloading configuration files to achieve rapid configuration
  2. The console interface needs to use the serial line in the package to realize the serial port management

MokerLink Commercial Series Switches A07

  1. Computer
  2. Wireless AP
  3. Camera
  4. Switch
  5. Serial Management
  6. USB Flas Disk
7 Login Management

This content is only applicable to managed type of products, please read this help information for the first application

Web Management

  1. Connect the device and PC, to ensure that the device initialization is complete.
  2. Configure the IP address of the PC to be in the same network segment as the switch default IP address
  3. Enter “https://192.168.2.1” in the address bar of the opened PC browser, then press “enter” to the web management login interface, input the default user name “admin” and password”admin”, and press “enter”.

MokerLink Commercial Series Switches A08

Console Port Management

1. Connect the PC and the switch console port with the console cable.
2. Start the terminal simulation software, create a connection, select a serial port, and set communication parameters in consistent with the default configuration of the switch’ s console port, as listed below:

Transmission rate : 115200
Data bits : 8
Parity bit : None
Stop bits : 1
Flow control mode : None

3. Press the Enter until the simulation terminal appears as follows, prompting the user to enter the user name and password. The default user name and password at first login is “admin”.

8 Indicator Definition

Indicator Definition State Description
PWR Power
Indicator Light on
Light off Powered

Abnormal
SYS| System
Indicator| Light on
Flash| System Normal
System Starting
PoE| PoE
Indicator| Light on
Light off| PoE Powered
No PoE Powered
1000M| Link Rate| Light on
Light off| Gigabit
10/100M
100M| Link Rate| Light on
Light off| 100M
Link Disconnect
Link/ACT| Link &Data| Light on
Flash| Link is Normal
Data Transmission
Mode/SW| Dial Switch
Indicator| Light on
Flash
Light off| VLAN
Extend
Default
Loop| Loop Alarm| Light on| Port Loop

9 PoE Powered Function

This function is applicable to PoE switches, not applicable to non-PoE switches

Standard PoE Power Supply

MokerLink Commercial Series Switches A09

  1. PoE Switch
  2. 12/36 is the power supply and data pin
  3. PoE Camera

Passive Poe Power Supply

MokerLink Commercial Series Switches A09

  1. Passive PoE Switch

  2. 12/36 is the data pin 45/78 is the power supply pin

  3. Intercom System

  4. Standard PoE power supply includes: protocol detection, power pin sequence detection, power output, abnormal protection, Link abnormal monitoring

  5. The PoE power supply protocol includes: IEEE802.3af (15.4W), IEEE802.3at (30W), IEEE802.3bt (90W)

  6. The standard PoE power pin sequence is 12+/36-, and the passive PoE power pin sequence is 45+/78-

  7. The standard POE switches can automatically detect and supply power to the PDs that meet the standard, non-POE devices are not powered and only transmit data

  8. Passive PoE switches use mandatory power supply mode, non-PoE powered devices may be burned out, please use with caution

  9. 24V POE switches have both low-voltage power supply and PD detection technology, which can provide 24V voltage on 45/78 pin, even if it is connected to non-standard equipment it will not burn out

10 States of Switch

Function Definition State Description
VLAN Port
Isolation Light on Designated port can not communicate with each other
Extend Link Extension Flash Designated port link extended to 250 meters
Default Normal Mode Light off All ports can communicate with each other
Reset Reset Button Flash Short press restart, long press more than 5

seconds reset configuration
AI PoE| PoE Watchdog| /| PDs crashed and restart automatically
Max| Power Display Indicator| Green
Yellow
Orange
Red| PoE Power output≤25%
PoE Power output≤50%
PoE Power output≤75%
PoE Power output≥75%

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals