RAB LIGHTING LCBAUX-B Low Voltage Luminaire Controller Instructions

September 20, 2024
RAB Lighting

RAB LIGHTING LCBAUX-B Low Voltage Luminaire Controller

Hello
The Lightcloud Blue Low-Voltage Luminaire Controller is a remotely controlled device used to enable switching and dimming. It converts any standard 0-10V dim-to-off LED fixture with a 12V output driver to a Lightcloud Blueenabled fixture which can be configured and controlled using the Lightcloud Blue mobile app.

Product Features

  • Wireless Control & Configuration
  • 0-10V Dimming
  • Power Monitoring
  • Patent Pending

Contents

Specifications & Ratings

  • PART NUMBER
    LCBAUX/B

  • RATINGS :
    IP66 Indoor/Outdoor

  • OPERATING TEMPERATURE:
    Max Temp: -4°F to 113°F (-20°C to 45°C)

  • DIMENSIONS:
    1.375” (D) x 1.75”(L)

  • OUTPUT :
    0-10V, 10mA max

  • OPERATION VOLTAGE
    12-36VDC, 0.1A max.

Setup & Installation

  1. Turn off power
    Find a suitable location

    • Lightcloud Blue devices should be positioned within 60 ft. of each other.

    • Building materials such as brick, concrete and steel construction may require additional Lightcloud Blue devices to extend around an obstruction.
      INDOOR

    • OUTDOOR

  2. Install the Lightcloud Blue Low- Voltage Luminaire Controller on a junction box
    Lightcloud Blue Low Voltage Controller is compatible with the Dim to Off 0-10V driver with 12V Aux supply, it can be mounted to any 1/2” NPT knockout hole on the fixture or junction box, with the radio module always outside any metal enclosure. if no sensor is used, then the RJ09 cable can be tied off and placed inside the fixture or box.

  3. Install luminaire
    Install the fixture with integrated Lightcloud Blue Low-Volta ge Luminaire Controller to a constant power source. Do not place Lightcloud Blue-controlled fixtures down circuit from any other non-Lightcloud Blue switching devices such as switches, sensors, or time clocks.

  4. Turn power on

  5. Verify power and local control
    Confirm Status Indicator is blinking red. Confirm local control using the Device Identification Button.

  6. Enable Device Pairing Mode
    If your Lightcloud Blue Low Voltage Luminaire controller is already paired, you can reset it by using the below methods.

    • Method 1: Delete from App
      Open the app and access the device settings for the paired device. Be sure that the controller is online and select ‘Delete”. The luminaire with flash on/off 3 times and the indicator light on the controller will turn red.

    • Method 2: Manual
      Press and hold the button for 10 seconds to until the luminaire flashes on/off 3 times and the indicator light on the controller is red.

    • Commission

    1. Download Lightcloud Blue App from Apple® App store or Google® Play.
    2. Tap the ‘+ Add Devices’ button in the Lightcloud Blue App to add the Controller while it is in pairing mode.
    3. Move to an Area and begin wireless control.

Functionality

Configuration
All configuration of Lightcloud Blue products may be performed using the Lightcloud Blue app.

Emergency default
If communication is lost, the Low-Voltage Luminaire Controller will revert back to the last known ‘On’ status. This setting can be adjusted using the Lightcloud Blue mobile app.
( Warning : Any wires not in use must be capped off or otherwise insulated.)

FCC STATEMENT

FCC Information:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

Note : This device has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
  • To comply with the FCC’s RF exposure limits for general population / uncontrolled exposure, this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
  • CAUTION : Changes or modifications to this equipment not expressly approved by RAB Lighting may void the user’s authority to operate this equipment.

Lightcloud Blue is a Bluetooth mesh wireless lighting control system that allows you to control RAB’s various compatible devices. With RAB’s patent- pending Rapid Provisioning technology, devices can be quickly and easily commissioned for residential and large commercial applications using the Lightcloud Blue mobile app. Each device in a system can communicate with any other device, eliminating the need for a Gateway or Hub and maximizing the control system’s reach. Learn more at www.rablighting.com

©2024 RAB LIGHTING Inc.
Made in China
Pat. rablighting.com/ip
1 844-544-4825
P-100927.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

RAB Lighting User Manuals

Related Manuals