Quantek CP-611LSR-V2.0 Laser Photocell Sensor Instructions

: September 18, 2024
: QUANTEK

Table of Contents

CP-611LSR-V2.0 Laser Photocell Sensor
Product Specifications:
Product Usage Instructions:
Installation:
Range Calibration:
Operation and Maintenance:
Additional Notes:
- Frequently Asked Questions (FAQ):
Q: Can the device be used in heavy rain or fog?
Q: How do I clean the lens of the device?

CP-611LSR-V2.0 Laser Photocell Sensor

“`html

Product Specifications:

Model: CP-611LSR-V2.0
Type: Laser Photocell Sensor
Includes Rain Shield
Power Requirement: Two terminals for power
Relay Contact: Two isolated relay contacts, set to N/O or
N/C
Range Threshold: 2 to 7.5 meters
Self-learning Range Calibration: Up to 8 meters
Operating Conditions: Recommended maximum range setting of 4
meters in heavy rain or fog

Product Usage Instructions:

Installation:

Fix the rain shield to outside walls first.
Ensure the device is perpendicular to the beam when fixing the
beam base plate.
Pass a four-core cable through the grommet at the bottom of the
device.
Connect the two power terminals and two isolated relay contacts
according to your setup (N/O or N/C).

Range Calibration:

Set the DIP switches or use the learning method to calibrate
the range threshold.
To self-learn a threshold range:
Set all DIP switches to OFF.
Place a target 200mm from the desired range.
Power up the device and wait for the beep.
Cross the beam 5 times at 0.5m from the sensor within 4
seconds.
Adjust the target if necessary until the green light flashes
rapidly.
When a long beep sounds, the threshold is set.

Operation and Maintenance:

Check the operation by moving the target 200mm closer after
calibration.
Avoid waving 5 times in front of the sensor on power-up to
prevent resetting.
For heavy rain or fog conditions, limit the range setting to 4
meters for optimal detection.
Clean the lens regularly to maintain proper functionality.

Additional Notes:

The device can be used for activation or secondary safety
purposes.
For vehicle detection, consider using two devices spaced 2
meters apart and wired in series.
The device does not differentiate between pedestrians and
vehicles.

Frequently Asked Questions (FAQ):

Q: Can the device be used in heavy rain or fog?

A: In heavy rain or fog, it is recommended to limit the range
setting to a maximum of 4 meters for optimal detection.

Q: How do I clean the lens of the device?

A: Use a clean, soft cloth to gently wipe the lens of the device
to maintain proper functionality.

“`

11 Callywhite Business Park, Callywhite Lane, Dronfield S18 2XP +44(0)1246 417113 sales@cproxltd.com www.quantek.co.uk

Specification: 7 fixed ranges plus full auto adjustment Maximum 8M 10-30V dc 10-24V ac Iq = 65mA, I detect = 28mA Dimensions 37 x 36 x 108mm Environmental rating IP65 0.8A @ 30Vdc volt free N/O or N/C Operating temp -10° C to 60° C

CP-611LSR-V2.0
Laser Photocell Sensor

Rain shield Included

The PCB has only one orientation, no angular adjustment. Be sure the surface is perpendicular to the beam. Fix the rain hood to outside walls first, then fix the beam base plate. The device takes a four core cable through a grommet in the bottom. Two terminals for power. Two for the isolated relay contact, set to N/O or N/C.
The setting routine calibrates the range threshold, but 200mm less than the actual position of the target. Threshold can be set by DIP switch or learning. There are 7 presets 2 to 7.5M
Self learning: The setting procedure will not learn a target over 8m from the device. To learn a threshold range, set all DIPs to OFF, then ……….
1. Place target in the beam 200mm from desired range. 2. Power up, and wait for the beep. You now have 10secs 3. Cross beam 5 times at 0.5m from sensor within 4 secs. 4. There are 5 beeps, then the green light flashes rapidly 5. Adjust the target if necessary. 6. When the long beep sounds, the threshold is set
Check operation by moving the target 200mm closer. The setting will be kept on power outs, but do not wave 5 times on power up!

200mm 5 times
A versatile device, can be used as activation or secondary safety.

Preset dip switch settings
Self learning
With Bracket 8M
8M Heavy rain or fog may impair detection on longer range, for this reason secondary safety applications should be set to a maximum of 4 metres range. The device does not distinguish between pedestrians and vehicles. 2 devices spaced 2 metres apart, wired in series, is advised for vehicle detection. Keep the lens clean.