eufy T8L00 Security Permanent Outdoor Light User Guide

Eufy Security Permanent Outdoor Light E120 User Guide (T8L00/T8L01)

What’s in the box At a Glance Testing the Light Setting up the System Installing your Outdoor Light Specifications Troubleshooting

What’s in the box100ft/30M

At a Glance

① Power Adapter
② Control Unit (Power Button)

• Press to turn on or
• Press and hold for 2 seconds to

③ Light String
➃ Waterproof Cap

Testing the Lights

Connect the light strings with the adapter unplugged. Avoid connecting while the adapter is plugged. If you connect the light strings while adapter is plugged, the strings may not light up.
A maximum of 6 light strings can be connected to the power adapter.

1. Connect all light strings together, then connect them to the control box and power adapter. Secure the waterproof caps for each connection and the end of the last light

2. Plug in the power supply to verify that each light string is working If some of the light strips do not light up, unplug and replug the power adapter. Make sure the light strings are working properly before proceeding to the next

3. See “Troubleshooting” for other lighting problems that may

Setting up the System

1. Download and install the eufy Life app, then sign in or create an
   Make sure that the Eufy Life app is version 2.11.0 or later to support this light string

2. Follow the in-app instructions to add this device and complete the

Installing your Outdoor Light

Install the light strings beneath the eaves to generate a wall-washing effect.
The installation will take approximately 30 minutes to 1 hour and may vary depending on the home type.

Choose a Locatioin

Do not install on rainy or hot days to avoid falling due to extreme temperatures or a slippery ladder.
Do not cut the light strings.
Determine the location of the first light string section, making sure that the power adapter is close enough to plug in and the control unit is accessible enough to operate.

The control unit and power adapter are not waterproof. If you want to install them outdoors, please contact Customer Service for a waterproof electrical box or consult an electrician.

Install the Light String

You will need a ladder and make sure it is stable enough or use it with the help of another person.
Use the extension cable if needed.

1. Clean the surface with a cloth or tissue and wait until the surface is completely dry before
   Dust residue may affect the adhesion of 3M

2. For the best wall-washing effect, the light string should be installed 2-4 inches (5-10 cm) away from the wall surface. Use the provided positioning card for measurement

3. Remove the protective film from each

4. Peel the VHB adhesive from the back of each light, then firmly press the light against the surface for at least 5 seconds.

   • Do not overstretch the wires between lights and allow for flexibility in

5. For permanent use, secure with cable clip and screw between every two

6. Specifications

• Input (Power Adapter)| 120V AC ~, 50/60Hz (US)

100-240V AC ~, 50/60Hz (EU, UK, Australia)

---|---
Input (Lights)| 36V⎓1.5A
Length (Light Strings)| T8L00: 100ft (30m) T8L01: 50ft (15m)

Length (Other Components)

| Control Unit: 13ft (4m) Power Adapter: 8.5ft (2.6m) Extension Cable: 12ft (3.6m)

Waterproof

| Light Strings: IP67

Control Unit: Indoor Use Only Power Adapter: Indoor Use Only

Light Displaying Technology| RGBWIC
Working Temperature| Product Set: -20℃ to 45℃ (-4 ℉ to 113 ℉ ) Light Strings: -20℃ to 60℃ (-4 ℉ to 140 ℉ )

Troubleshooting

1. Light doesn’t glow at all / Some light do not
   • If only the first string glows while the power adapter is plugged in, unplug the power adapter and plug it in again.
   • If some lights don’t glow, disconnect all components, then reconnect all components and plug the power adapter in again.
   • If any of the selected light effect are not fully displayed, contact eufy support team for further analysis or product replacement.
2. Cannot connect to Wi-
   • The 5GHz network is not Please set the router to 2.4GHz and then reset it.
   • Do not skip the Wi-Fi connection steps in the
   • Make sure you have entered the correct Wi-Fi name and
   • Connect the hotspot of your phone to the
3. Adhesive stickers don’t
   • Clean the surface with a cloth and make sure there is no
   • Remove the original sticker and replace it with the replacement
   • Make sure to press against the surface for at least 5 seconds when installing the
   • Use a cable clip and screws for

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>