Quantek CP5-RX Versatile 3 in 1 Wiegand Proximity Reader and Keypad Instruction Manual
- June 9, 2024
- QUANTEK
Table of Contents
Quantek CP5-RX Versatile 3 in 1 Wiegand Proximity Reader and Keypad
Introduction
It is a waterproof Wiegand output keypad, with integrated proximity reader, that can be mounted either indoors or outdoors in harsh environments.
Four versions are available:
- EM version: read 125KHz EM card only
- EM+HID version: can read both 125KHz EM and HID cards
- Mifare version: can read 13.56MHz Mifare card
- EM+HID+Mifare version: can read 125KHz EM+ 125KHz HID+ 13.56MHz Mifare cards
Features
- Waterproof, conforms to IP66
- Programmable Wiegand output: 26-44, 56, 58 bits
- Programmable Keypad Transmission: 4bits, Bbits or virtual card number format
- Card type: EM card or EM+HID cards or Mifare card, or EM+HID+Mifare cards
- Reading range: 3~8cm
- External LED Control & External Buzzer Control
Specification
Version | EM | EM+HID | Mifare | EM+ HID+ Mifare |
---|---|---|---|---|
Frequency | 125KHz | 125KHz | 13.56MHz | 125KHz & 13.56MHz |
Card Type | 125KHz EM Card | 12 |
I H a &
| 13.56MHz Milare
Card
| 125KHz EM&HID Cards &
13.56MHz Milare Card
Read Range| 3-8cm
Standby Current| S35mA
Operating Voltage| 9~18VDC
Wiegand Output Format| Wiegand 26-44, 56, 58 bits output
(Factory default: 26bits for EM card, 34bits for Mifare card, Auto output for HID card)
Keypad Transmission
Format
| 4bits (factory default)
8bits or virtual card number format can be set
Operating Temperature| -40°(-60°(
Operating Humidity| 0%RH-95%RH
Physical| ABS, Metal optional
Color| ABS: Black/Ivory| Metal: Silver
Index of Protection| IP66
Dimension| ABS: L122 x W50 x D21 mm| Metal: L148 x W56 x D22.5 mm
Net Weight| ABS: 155g| Metal: 450g
Shipment Weight| ABS:210g| Metal:500g
Installation
- Drill 2 holes (A, C) on the wall for the screws and one hole (B) for the cable
- Knock the rubber bungs to the holes (A, C)
- Fix the back cover on the wall with 2 screws
- Thread the cable through the cable hole (B)
- Attach the unit to the back cover
Wiring
Connection Diagram
Programming
Change the configure settings according to your application (optional). Multiple configuration settings can be changed at one time: enter program mode, change desired settings, then exit program mode.
Set M aster Code
The 4-6 digits Master Code is used to prevent unauthorized access to the
system. To interface with the keypad reader, the manager will need a Master
Code (factory default code: 1 2 3 456), we highly recommend immediately
updating it and recording the New Master Code.
Note:
When entering program mode, please press* for 5 seconds, and then press Master
Code #.
Programming Step | Keystroke Combination |
---|---|
1. Enter Program Mode | * (Master Code)# |
2. Update Master Code | O (New Master Code)# |
( Repeat New Master Code)#
3. Exit|
Packing List
Name
|
Quantity
---|---
Keypad Reader| 1
Manual| 1
Wall Fixing Plugs| 2
Self Tapping Screws| 2
Set Wiegand output format for EM Card
Set Wiegand output format for HID Card
Programming Step | Keystroke Combination |
---|---|
1. Enter Program Mode | * (Master Code)# |
2. Format Setting | 2(0)# |
(Auto output, factory default) 2 (26-37) #
3. Exit|
Set Wiegand output format for Mifare Card
Programming Step | Keystroke Combination |
---|---|
1. Enter Program Mode | * (Master Code)# |
2. Format Setting | 3 (0) # (Auto output) |
3 (26-44, 56, 58) #
(Factory default is 34bits)
3. Exit|
Set PIN output format
The keypad reader can be set to 4 bits (factory default), 8 bits, or virtual
card number format.
Programming Step | Keystroke Combination |
---|---|
1. Enter Program Mode | * (Master Code)# |
2. Format Setting Virtual Card Number | 4 (0)# |
4Bits | 4 (4)# |
BBits | 4 (8)# |
3. Exit |
Set Audible and Visual Response
Programming Step | Keystroke Combination |
---|---|
1. Enter Program Mode | * (Master Code)# |
2. LED Always ON | 5 (1) # (Factory default) |
LED Always OFF | 5(2)# |
OR
2. Enable Sound
| 5 (3) # (Factory default)
Disable Sound| 5(4)#
OR|
Keypad Backlit Always| 5 (5) # (Factory default)
ON|
Keypad Backlit| 5(6)#
Automatic OFF|
| Automatic OFF after 20
| seconds, it will go ON by
| pressing any key (this key
| isn’t taken into consideration)
3. Exit|
Reset to Factory Default:
There are two methods to reset the device to factory default.
Method 1:
(Master Code)# 5(0) #
Method 2
(This way is suitable for users who forget the Master Code):
Power off, connect the Yellow cable and GND cable, and then power on, hold it for 5 seconds, there will be a long beep, which means reset to factory default successfully.
Data Signal
The below table shows the waveform of pulse width time (the duration of a pulse) and pulse interval time (the time between pulses) of the Wiegand data output from the readers. (Example 1010)
Keypad Transmission Format
The default keypad transmission format is 4 bits, 8 bits or virtual card number format can be set.
Virtual Card Number
The reader will transmit the PIN data when it receives the last key(#) after
the PIN code
Example: PIN code: 999999 Press 999999 #, then the output format will be: 0000999999
4 bits
The reader will transmit the PIN data after every key is pressed:
- 1 (0001),2(0010),3(0011)
- 4 (0100), 5 (0101 ), 6 (0110)
- 7 (0111), 8 (1000),9 (1001)
-
- (1010), 0 (0000), # (1011)
- 4 (0100), 5 (0101 ), 6 (0110)
- 7 (0111), 8 (1000),9 (1001)
-
- (1010), 0 (0000), # (1011)
8 bits
The reader will transmit the PIN data after every key is pressed:
- 1 (1110 0001), 2 (1101 0010), 3 (1100 0011)
- 4 (1011 0100), 5 (1010 0101 ), 6 (1001 0110)
- 7 (1000 0111 ), 8( 0111 1000),9 (0110 1001)
-
- (0101 1010), 0 (1111 0000), #(0100 1011)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>