FLOS Belve Dere Clove 2 LED Bollard Light Instructions

: September 12, 2024
: FLOS

Table of Contents

FLOS Belve Dere Clove 2 LED Bollard Light
Product Usage Instructions
INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FLOS Belve Dere Clove 2 LED Bollard Light

Specifications

Product Name: Belvedere
Designer: Antonio Citterio
Usage: Outdoor
Risk Group: 1 (IEC/TR 62778:2014)
IP Rating: Must match or exceed luminaire’s IP rating
Cable Length: Maximum 100 mm

Product Usage Instructions

Installation and Maintenance
Connection and maintenance of the luminaire must be carried out by trained and qualified staff only in compliance with national safety regulations. Do not open the product in case of failure bu contact the support service.

FAQ
Can I replace the LED module in the luminaire myself?
No, the LED module contained in this luminaire should be replaced by the manufacturer only. Contact your supplier for further assistance.

Connection and maintenance of the luminaire must be carried out by trained and qualified staff only in compliance with national safety regulations. Do not open the product in case of failure but contact the support service.
Make sure there is no power connected to the fitting before carrying out any maintenance.
Risk Group 1 (IEC/TR 62778:2014)
The LED module contained in this luminaire shall be replaced by the manufacturer only. For further information, please contact your supplier.
Place the luminaire on a 20-30 cm drainage layer (gravel) and fill it with water. If after 30 minutes water is still in the luminaire it is compulsory to integrate an additional draining system (e.g. drain pipe).
To avoid water stagnation do not place the box for installation on hollow areas.
The protection rating of the electrical connection must be equal to or greater than the IP rating of the luminaire
The piece of cable must be <100mm long.
Use a suitable type of power supply cable (HAR H05 / 07 RN-F flexible cables or suitable for outdoor use): rigid cables can compromise the seal through the cable gland.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusi-vely replaced by the manu-facturer or his service centre, in order to avoid a hazard.
Keep the luminaire clean to prevent dirt deposit. On steel parts use dedicated cleaners only. Use a soft cloth and neutral soap to clean the device.
For easy maintenance (unscrewing) of the luminaire we recommend protecting screws threads with silicone grease before exposure to weather.
Keep away from aggressive agents and chemical sub-stances (e.g. fertilizer, weed-killer, lime).
In case of break of the glass/diffuser use original FLOS spare parts only.
During the installation and the maintenance of the fixtures it is IMPORTANT to be careful and avoid damage on the paint coating. Damages on the coating exposed to outdoor conditions or wa-ter could cause corrosion.

For all lighting devices, regularly scheduled maintenance of the installation should be carried out as per current laws in the countries where they are used and according to the instructions contained in this box:

Check the fastening of the screws.
Inspect cables and cable glands for any possible damage.
Check the fastening of cable glands.
Check if seals are in working order.
Defect or damaged components must be replaced before switching the luminaire on. Use original spare parts only.
It is important to carry out luminaire maintenance at each bulb substitution or at least once per year.
Any improper use or installation, any tampering or any unauthorised modification of the luminaire causes the immediate expiry of the warranty on the luminaire and of any claim against the manufacturer. Should Ares allow the return of a luminaire for technical inspection or tests, they must be returned with a piece of wiring cable (10-20cm connected to the luminaire).

IP65 IK04_IK08

BELVEDERE CLOVE1/2
100-240V/50-60Hz
Total power 8,4W
CLASS
MID-POWER LEDs
2700K_3000K_4000K
Integral electronic power supply

The safety of the device is guaranteed only by respecting existing regulations in the countries where the device is used and by following the instructions contained in this box. These instructions should therefore be saved. Compliance with these instructions is essential for the correct operation of the device and system.

Dust-tight and protected against waterjets IP65
Class light fixture
Protection against impact IK04 (B. SPOT) IK08 (B.CLOVE)
Marking

INSTALLATION

CABLAGGIO – WIRING

INSTALLATION WITH SPIKE

Directive 2002/96/EC (Waste Electrical and Electronic Equipment – WEEE):

Information for users.
This product complies with EU Directive 2002/96/EC. The crossed-out wastebasket symbol on the appliance means that at the end of its usefull lifespan, the product must be disposed of separataly from ordinary household wastes. The user is responsible for delivering the appliance to an appropriate collection facility at the end of its useful lifespan. Appropriate separate collection to permit recycling, treatment and environmentally compatible disposal helps prevent negative impacts on the environment and human health and promotes recycling of the materials making up the product. For more informantion on available collection facilities, contact your local waste collection service or the shop where you boughl this appliance.

This information only applies to customers in the European Union, according to Directive 2002/96/EC of the European parliament and of the council of 27 January 2003 on waste electrical and electronic equipment (WEE) and legislation transposing and implementing it into the various national legal systems.

www.flos.com