SimpliFire SF-OD43 Forum 55 Outdoor Electric Fireplace Owner’s Manual

: August 6, 2024
: SimpliFire

Table of Contents

SimpliFire SF-OD43 Forum 55 Outdoor Electric Fireplace
Product Information
Usage Instructions
IMPORTANT INSTRUCTIONS
GENERAL INFORMATION
GETTING STARTED
INSTALLATION
MAINTENANCE
SimpliFire Troubleshooting Guide
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SimpliFire SF-OD43 Forum 55 Outdoor Electric Fireplace

Specifications

Model(s): SF-OD43, SF-OD55
Owner’s Manual: Installation and Operation
Country of Origin: China
Copyright: 2024

Product Information

Congratulations on selecting a SimpliFire Electric Fireplace, an elegant and clean alternative to wood and gas burning fireplaces. The SimpliFire electric fireplace is designed to provide safety, reliability, and efficiency.

Usage Instructions

Important Safety Instructions
Before attempting to assemble, install, operate, or maintain the product, carefully read all instructions provided in the manual. Failure to comply with the instructions may result in personal injury or property damage.

Safety Precautions
To reduce the risk of fire, electrical shock, or personal injury, follow these precautions:

Read and understand all instructions before plugging in and using the appliance.
Do not operate the appliance before reading and understanding the operating instructions.
Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage.
Basic precautions should always be followed when using electrical appliances to reduce the risk of fire, electric shock, and injury to persons.

Getting Started
Before starting the installation process, make sure you have the following:

Parts and hardware as listed in the manual.
Tools and supplies needed for installation.
Information on appliance weights and dimensions.
A suitable location with proper clearance to combustibles.
An electrical supply circuit that meets the requirements.

Operating Instructions
The SimpliFire Electric Fireplace can be operated using the following methods:

Operation with On-Device Controls: Follow the instructions provided in the manual for operating the fireplace using on-device controls.
Operating by Remote Control: If applicable, use the remote control as instructed to operate the fireplace.

FAQ

Q: What should I do if I encounter difficulties during installation?
A: If you face any challenges during installation or operation, please contact your SimpliFire dealer or visit www.hearthnhome.com for assistance.
Q: Can I modify the fireplace’s components?
A: Do not modify any components of the fireplace as it may void the warranty and compromise safety.

Owner’s Manual
Installation and Operation

Forum Series:
Model(s):
SF-OD43
SF-OD55

NOTICE
DO NOT DISCARD THIS MANUAL

Important operating and maintenance instructions included.
Read, understand and follow these instructions for safe installation and operation.
Leave this manual with party responsible for use and operation.

Congratulations!
Congratulations on selecting a SimpliFire Electric Fireplace, an elegant and clean alternative to wood and gas burning fireplaces. The SimpliFire electric fireplace you have selected is designed to provide the utmost in safety, reliability, and efficiency.
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE, OR MAINTAIN THIS PRODUCT.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE.

WARNING: To reduce risk of fire, electrical shock, or personal injury, read and understand all instructions, including safety information before plugging in and using this appliance.

Please contact your SimpliFire dealer with any questions or concerns. For the location of your nearest SimpliFire dealer, please visit www.hearthnhome.com.
Printed in China – Copyright 2024
SimpliFire • SF-OD43, SF-OD55 • 2047-980 Rev. D • 2/24

IMPORTANT INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING! Risk of Fire! Risk of Electrical Shock!
DO NOT:

Install or operate damaged appliance
Modify appliance
Operate the heater without fully assembling all components

Hearth & Home Technologies disclaims any responsibility for, and the warranty and agency listing will be voided by the above actions.

WARNING! DO NOT operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause fire or injury.
WARNING! Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Failure to install appliance according to Owner’s Manual could cause property damage or injury.

When using electrical appliances, basic precautions should always be followed to reduce risk of fire, electric shock, and injury to persons, including the following:

Read all instructions before installing this appliance.
Extreme caution is necessary when any appliance is used by or near children or other at risk individuals and whenever the appliance is left operating and unattended.
Do not operate any appliance if it malfunctions. Disconnect power at service panel and have appliance inspected by a reputable electrician before reusing.
Do not insert or allow foreign objects to enter the appliance as this may cause an electric shock, fire, or damage the appliance.
Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
Do not operate any appliance with a damaged cord, plug after the appliance malfunctions, has been dropped or damaged in any manner. Return appliance to authorized service facility for examination, electrical or mechanical adjustment or repair.
Never locate appliance where it may fall into a bathtub or water container.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from traffic areas and where it will not be tripped over. Do not tightly coil cord.
Always use properly grounded, fused and polarized outlets.
Always use ground fault protection where required by electrical code.
To disconnect appliance, turn controls to “OFF” then remove plug from outlet.
Always disconnect power before performing any cleaning, maintenance or relocation of the appliance.
To prevent electrical shock or fire, always use a certified electrician should new circuits be required.
When transporting or storing the appliance, keep in a dry place free from excess vibration to avoid damage.
Avoid use of an extension cord because an extension cord may overheat and cause a fire. However if you have to use an extension cord, the cord should be No. 14 AWG minimum size and rated to not less than 1875 watts.

SAVE THESE INSTRUCTIONS

Safety Alert Key

WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

Warranty

Hearth & Home Technologies LLC

LIMITED WARRANTY
Hearth & Home Technologies LLC (“HHT”) extends the following warranty for HHT gas, wood, pellet and electric hearth appliances (each a “Product” and collectively, the “Product(s)”) and certain component parts set forth in the table below (“Component Part(s)”) that are purchased from a HHT authorized dealer or distributor.
WARRANTY COVERAGE:
HHT warrants that the Products and their Component Parts will be free from defects in materials and workmanship for the applicable period of Warranty coverage set forth in the table below (“Warranty Period”). If a Product or Component Parts are found to be defective in materials or workmanship during the applicable Warranty Period, HHT will, at our discretion, repair the applicable Component Part(s), replace the applicable Component Part(s), or refund the purchase price of the applicable Product(s). The maximum amount recoverable under this Warranty is limited to the purchase price of the Product. This Warranty is transferable from the original purchaser to subsequent owners, but the Warranty Period will not be extended in duration or expanded in coverage for any such transfer. This Warranty is subject to conditions, exclusions, and limitations as described below.
WARRANTY PERIOD :
Warranty coverage begins at the date of installation. In the case of new home constructions, Warranty coverage begins six months after invoice of the final sale of the Product(s) by an independent, authorized HHT dealer or distributor. However, the Warranty coverage shall commence no later than 24 months following the date of Product shipment from HHT, regardless of the installation or purchase date.

Warranty Period	HHT Manufactured Appliances and Venting

Component

Parts

1 Year

|

X

|

X

|

X

| |

All parts including handles, external enameled components and other material except as covered by Warranty Conditions, Warranty Exclusions, and Warranty Limitations listed

2 Years

| | | | X| All parts except as covered by Warranty Conditions, Warranty Exclusions, and Warranty

Limitations listed

|

X

|

X

| |

Glass, Electrical components limited to heating element/igniters, Top feed auger assembly, Blowers, Junction Box, Remotes/Wall switches, linear actuator, power cord, vacuum switch, snap disc, wire harnesses and thermocouple

X

| | | |

Electrical components limited to modules, remotes/wall switches, valves, pilots, blowers, junction boxes, wire harnesses, transformers and lights (excluding light bulbs)

X| | X| | Cement Refractory Panels, Glass Liner Panels
3 years| | X| | | Firepots, burnpots, Harman mechanical feeders

5 years

|

X

| |

X

| |

Catalysts, Vented and Vent Free burners and logs

10 years

|

3 years

| |

X

|

X

| | Castings, Medallions & Baffles, FlexBurn® System (engine, inner cover, access cover and fireback), Firebox and heat exchanger, HHT Chimney & Terminations, Manifolds
20 years| 3 years| X| | | | Firebox and heat exchanger
All purchased replacement parts and optional accessories
1 Year| None| X| X| X| X| All purchased replacement parts and optional accessories

WARRANTY CONDITIONS:

Because HHT cannot control the quality of any Products sold by unauthorized sellers, this Warranty only covers Products that are purchased through an HHT authorized dealer or distributor unless otherwise prohibited by law; a list of HHT authorized dealers is available on the HHT branded websites.
This Warranty is only valid while the applicable Product remains at the site of original installation.
This Warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the applicable Product is authorized to sell applicable Product.
Contact your installing distributor or dealer for Warranty service. If the installing dealer or distributor is unable to provide necessary parts, contact the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking Warranty service from a dealer other than the dealer from whom you originally purchased the applicable Product.
No HHT consumer should bear cost of warranty service or costs incurred while servicing warranty claims (i.e., travel, gas, or mileage) when the service is performed within the terms of this Warranty. Check with your dealer or distributor in advance for any costs to you when arranging a warranty call. Travel and shipping charges for parts are not covered by this Warranty.

WARRANTY EXCLUSIONS
This Warranty does not cover the following:

Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and exterior surface finishes may occur. This is not a flaw and is not covered under the Warranty.
Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
Repair or replacement of parts that are subject to normal wear and tear during the Warranty Period are not covered. These parts include: paint, wood and pellet gaskets, firebricks, wood grates, flame guides, batteries and the discoloration of glass.
Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to this noise are not covered by this Warranty.
Damages resulting from: (1) failure to install, operate, or maintain the applicable Product in accordance with the installation instructions, operating instructions, and listing agent identification label furnished with the applicable Product; (2) failure to install the applicable Product in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or forced air furnaces or other such causes; (6) use of fuels other than those specified in the operation instructions; (7) installation or use of components not supplied with the applicable Product or any other components not expressly authorized and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing; and/or (9) interruptions or fluctuations of electrical power supply to the applicable Product.
Non-HHT venting components, hearth connections or other accessories used in conjunction with the applicable Product.
Any part of a pre-existing fireplace system in which an insert or a decorative gas applicable Product is installed.
HHT’s obligation under this Warranty does not extend to the Product’s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper Product for the application. Consideration must be given to the Product location and configuration, environmental conditions, insulation and air tightness of the structure.

This warranty is void if:

The applicable Product has been over-fired, operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, deformation/warping of interior cast iron structure or components, rust colored cast iron, bubbling, cracking and discoloration of steel or enamel finishes.
The applicable Product is subjected to prolonged periods of dampness or condensation.
There is any damage to the applicable Product due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation.

LIMITATIONS OF REMEDIES AND LIABILITY:
EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. The owner’s exclusive remedy and HHT’s sole obligation under this Warranty or in contract, tort or otherwise, shall be limited to, at HHT’s sole option, replacement of the Component Part(s), repair of the Component Part(s), or refund of the original purchase price of the applicable Product(s). In no event will HHT be liable for any incidental or consequential damages caused by defects in the applicable Product. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from State to State. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE FOR THE APPLICABLE PRODUCT. Some States do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

GENERAL INFORMATION

Appliance Certification

MODELS: SF-OD43, SF-OD55
LABORATORY: ETL Intertek
TYPE: Luminaires; Household and Commericial
Furnishings
STANDARD: CSA C22.2 No 250; UL 962

NOTICE: This installation must conform with local codes.
NOT INTENDED FOR USE AS A HEAT SOURCE. This appliance is not equipped with a heater.

Note: The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:

Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

WARNING: This product can expose you to Di-(2-ethylhexyl) phthalate, which is known to the State of California to cause cancer and reproductive harm. For more information go to: www.P65Warnings.ca.gov.

Unpacking and Inspecting Appliance
WARNING! DO NOT use this Electric Fireplace if any part has been under water. Immediately call a qualified service technician to inspect and to replace any part of the electrical system if necessary. Keep plastic wrapping away from children.

Carefully remove the appliance and components from the packaging. Discard packaging.
Carefully inspect components for any damage.
Reference parts list to verify all parts have been received.
Read all the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

Model and Serial Number Information
The model and serial number information is located on the rating plate. The rating plate is located behind the glass on the top interior surface of the viewing area.

Homeowner Reference Information
We recommend that you record the following pertinent information about your fireplace.

Model Name: ___
Date purchased/installed: __
Serial Number: __
Location on fireplace: _____
Dealership purchased from: ___
Dealer Phone: __
Notes: ___

GETTING STARTED

Parts and Hardware

Parts and Hardware List

Tools and Supplies Needed
Before beginning the installation be sure that the following tools and building supplies are available.
Tape measure
Gloves
Level
Square
Magnetic screwdriver, or electric screw gun with Phillips bit
Safety glasses
Drill
3/32 slotted head screwdriver/or equivalent
Outdoor specific installation:

Exterior Silicone Caulk Sealant
Preferred Flashing Method, such as:
- Flashing Tape
- Aluminum Flashing
- or available Drip Pan (SF-OD**-DP)

Appliance Weights and Dimensions

Model	Pounds	Killigrams
SF-OD43	110	50
SF-OD55	132	60

APPLIANCE WITHOUT FRONT TRIM

Model| | A| B| C| D| E| F| G| H| I| J| K| L| M
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---

SF-OD43

| in.| 43-1/2| 46| 15-3/8| 18-1/8| 43-3/4| 8| 5| 3-3/4| 1| 15-3/4| 1-3/8| 1/2| 8-1/4
mm| 1104| 1168| 392| 460| 1110| 203| 127| 95| 25| 400| 36| 13| 210
SF-OD55| in.| 55-1/2| 58| 15-3/8| 18-1/8| 55-3/4| 8| 5| 3-3/4| 1| 15-3/4| 1-3/8| 1/2| 8-1/4
mm| 1409| 1473| 392| 460| 1415| 203| 127| 95| 25| 400| 36| 13| 210

APPLIANCE WITH FRONT TRIM

Model| | A| B| C| D| E| F| G| H| I| J
---|---|---|---|---|---|---|---|---|---|---|---
SF-OD43| in.| 43| 48| 15| 20| 46| 1-1/8| 1/8| 1-1/8| 3/4| 8-3/4
mm| 1092| 1219| 380| 507| 1168| 29| 3| 29| 19| 223
SF-OD55| in.| 55| 60| 15| 20| 58| 1-1/8| 1/8| 1-1/8| 3/4| 8-3/4
mm| 1397| 1523| 380| 507| 1473| 29| 3| 29| 19| 223

Location
Note: The Forum appliance is designed for indoor/out-door use. The appliance is weather resistant and must be installed in a framed wall. The appliance is equipped with a GFCI power cord or can be hardwired.
When choosing a location for your fireplace ensure that the following general rules are followed:

The Forum fireplace is designed to work best when ambient light levels are low. If the Forum is installed in brightly lit areas or in direct sunlight, the strong reflections may diminish the flame. For best results, install out of direct sunlight.
Power supply service must be installed within proximity of electric fireplace prior to finishing to avoid reconstruction.
See Figure 3.2 to determine location of appliance installation.

Clearance to Combustibles
See Section 4.A for framing dimensions. Minimum Clearance to Combustible Construction

Sides…………………..0 in.
Floor……………………0 in.
Top……………………..0 in.
Back……………………0 in.
Front……………………0 in.
Mantel…………………0 in.
Mantel Depth……….Unlimited.

See Figure 3.2.

Electrical Supply Circuit Requirements
Plan the location of the appliance so that it will have ad-equate electric power. A minimum 15 AMP, 120V/60Hz circuit is required.
If hardwiring for an outdoor appliance, the circuit must be Ground Fault Circuit Interrupter (GFCI) Protected.

INSTALLATION

WARNING! Risk of Personal Injury or Property Damage! Failure to install the appliance as instructed below may result in damage to the equipment and or may expose the user to the risk of fire, serious injury, illness or death.
NOTICE: These instructions are not substitutes for the requirements of local building codes.
The appliance shall be installed into a wall as a stand-alone structure, or into an exterior bump out wall separate of the structures weather envelope. There are two installation methods, built-in with finishing materials over the appliance for a frameless look (this is a permanent installation) or recessed with finishing materials up to the opening, using a self-trimming front (this is a removable installation). See Figure 4.1.

Framing Dimensions

Appliance Preparation
Removing Front Finishing Trim:
To remove the front finishing trim, remove the two (2) Phil-lips screws located at the top of the trim. See Figure 4.2.
With the screws removed pull the friction fit trim straight out and away from the appliance.

Glass Removal:
To remove the front viewing glass, remove the screws attaching the glass retaining bracket to the appliance. See Figure 4.3.
With the retaining bracket removed from the appliance, use the provided suction cup to pull the glass forward. Do not rely on the suction cup for lifting of the glass! See Figure 4.4.
Carefully tilt the glass forward and lift it out of the bottom channel and away from the appliance. See Figure 4.4.
Set glass aside by placing one edge on a soft surface.

Interior Side Panel Removal:
To access the appliance mounting holes, the interior side panels must be removed.
Remove the left and right interior side panels by removing the two (2) screws attaching them to the appliance ceiling. Use the small tab located on the top of each panel to pull the top downward and away from the appliance side wall. The panel’s bottom tab will lift out of the appliance. Repeat for both sides. See Figure 4.5.

Chase Construction and Moisture Resistance
This outdoor appliance will shed moderate amounts of water, but is not waterproof. This appliance must be enclosed or covered with finishing material and all joints sealed to prevent water infiltration.
This appliance will not perform as an exterior wall. Moisture penetration must be considered for construction that places the appliance in a wall or within moisture sensitive materials.
When installed on exterior walls: Hearth & Home Technologies recommends that the chase be constructed outside the structure’s weather envelope. Where the plat form meets the wall, use a flashing detail similar to that required for attached decks. Chase platforms, including hearths should slope away from the structure at 1/8 in. to 1/4 in. per foot. The appliance can be shimmed level.
Water Drainage: The Forum is designed to operate outdoors experiencing rain and other sources of moisture. The appliance is designed to drain excess moisture out weep holes lated on the appliance base. When constructing the enclosure, the builder must provide a means of draining water from under the appliance and out of the structure. This can be achieved by properly positioned drain holes, slots or other means for all water to exit at the lowest grade of the structure. Choosing the location of the appliance is also important so that an area that may experience excessive water flow or standing water is avoided. In some cases a drain pan is needed to ensure proper drainage. This can be constructed from corrosion resistant metal, or suitable material for outdoor use with a water resistant membrane. A slope of 1/4” per foot toward the drain ports of the structure is recommended. A drain pan can also be purchased (SF-OD43-DP) for the 43 inch appliance or the (SF-OD55-DP) for the 55 inch appliance.

Flashing

Flash the appliance in a manner consistent with regional practices to prevent water penetration around the appliance.
For brick, stone, stucco and similar construction, weep screeds should be installed per regional codes.
See Figures 4.7 and 4.8 for more information regarding wall and enclosure construction required to prevent moisture penetration into the structure. The appliance will shed moderate amounts of water but is not waterproof.

Be sure to plan a drain system for your installation.

NOTICE: If the optional drain pan is not used during construction ensure any water build-up can escape to the exterior of the finished enclosure.
Water penetration can occur, and accumulate below the appliance, and if not taken into consideration can cause deterioration of materials, and may cause premature failure of the structure.

Installation

Connect to electrical service. Reference Section 4. F.
Install the appliance into the opening. Ensure that weight of appliance is fully supported by floor or bot- tom framing member. Level with shims if necessary. Ensure that it is centered left to right, then fasten it directly to the framing.
For recessed installations using the Front Trim, the appliance should be pushed into the finished opening until the outer edge of the finishing stops are
flush with the finished surface. See Figure 4.8.
With the appliance in place, leveled and plum, attach it to the framing using 4 sets of the provided rubber bushings, washers, and wood screws through the appliance mounting holes. See Figure 4.6.

Finishing
Maximum finishing differ between built-in overlap and recessed installations. Refer to Figure 4.7 and 4.8.

Built-In Overlap Installations

Finishing
Maximum finishing differ between built-in overlap and recessed installations. Refer to Figure 4.7 and 4.8.

Built-In Overlap Installations

Recessed Installations

A corrugated splatter guard is included as part of the packaging of the Forum. This may be used to mask the viewing area during the finishing steps of the installation. See Figure 4.9.

Electrical Connection / Installation

Note: All wiring must be completed prior to finishing the appliance.
All electrical connections shall be performed by a qualified electrician.
WARNING! Risk of Fire, Electrical Shock and Injury! Electrical wiring must comply with local building codes and other applicable regulations.
WARNING! Risk of Shock! Label all wires prior to disconnection when servicing the appliance. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
Note: The appliance must be connected and grounded in accordance with local codes and / or the current ANSI/NFPA 70 National Electric Code or CSA C22.1 Canadian Electrical Code.

This Appliance ships with a GFCI protected power cord installed. The power cord may be removed from the junction box enclosure for use with hardwired applications.
For hardwired installations, a minimum 15 AMP, 120V/60Hz Ground Fault Interupter (GFCI) circuit is required outdoor only.

Hard Wire Installation:

Remove the terminal block housing on the right top end of the appliance, by removing two phillips screws. On the underside of the terminal block housing remove the two remaining phillips screws attach- ing the cover plate to the housing. See Figure 4.10.
Loosen the cord grip on the power cord side of the housing.
Use a 3/32 slotted screwdriver or equivalent or depress the spring loaded terminals to remove the power cord.
Terminate type NM-B wire to the terminal block, ensure connections are secure, and tighten the cord grip. Use 3/32 slotted head screwdriver, or equivalent, to depress the spring-loaded terminals for the conductors.
Replace terminal block housing and cover plate with retaining screws.

Appliance Final Setup
Glass Removal:
Refer to Section 4.B.

Media Placement:
Note: There are no specific requirements for media installation. Crystal and log media are included, but not required. The placement instructions provided are the most popular configurations to display the included media.

Clear Crystal Media Placement:
Carefully spread the small clear crystals across the ember bed. Then evenly arrange the large crystals on top of or within the small crystal media. See Figure 4.11.

Log Media Placement:

Evenly spread the black embers and clear small crystals across the ember bed. The black embers provide a more realistic ember look with the logs. Clear crystals can be mixed in if desired. Adjustments can be made for your individual preference.
Place the smaller logs evenly spaced on the ember bed as shown in Figure 4.12.
Arrange the larger logs so that one end rests on top of a smaller log. Refer to Figure 4.13 as an example.

Glass Installation

Use the provided suction cup to set the bottom edge of glass into the glass channel and tip back into the appliance until it rests against the glass stops. Do not rely on the suction cup for lifting of the glass!
Secure the glass in place by attaching the glass retaining bracket to the appliance using the supplied Phillips screws. Refer to Appliance Preparation Section 4.B and figure showing glass removal.

OPERATING INSTRUCTIONS

WARNING! Risk of Fire, Electrical Shock, and Injury! Do not operate the appliance if it is damaged or has malfunctioned. If you suspect the appliance is damaged, call a qualified service technician to inspect and replace any part of the electrical system if necessary.
The appliance can be operated by both remote control and manual buttons located on appliance. Once the power is supplied to the appicance, the power button can be pressed a beep should be heard when the appliance turns on. See Figure 5.1.

Operating Temperatures: +14 °F to +104 °F (-10 °C to +40 °C)
Non-Operating / Storage Temperatures: -20 °F to +140 °F (-29 °C to +60 °C)

Operation with On-Device Controls

Power Button
The Power button turns the power of the appliance ‘ON or OFF’.
Flame Button
By pressing the Flame button, the appliance will cycle through four flame effects.
Fuel Bed Button
The Ember Bed LED light button will turn on the LED lights and cycle through 14 color themes (13 colors and a color rotating option).
Flame Brightness Button
The Flame Brightness button will cycle through four brightness settings. This adjusts Accent/Flame/Fuel Bed brightness levels simultaneously.

Operating by Remote Control

The appliance Main Power button must be in the “ON” position for the remote control to function.
Make sure batteries are properly installed in Remote Control.
Battery requirements 2 x AAA batteries (included).
The effective range of the remote is up to 16 ft.
The remote control must be within the 16 ft. range and also be pointed directly at the face of the appliance. For best results, point the remote control toward the remote receiver location. See Figure 5.1.

This remote control is not outdoor rated and should be stored indoors and away from the elements when not in use.

MAINTENANCE

Maintenance
WARNING! Risk of Shock! Always remove power before moving or servicing. Do not immerse appliance in water.

Before cleaning or servicing, always turn off appliances and remove power, by either unplugging from the wall outlet or shutting off circuit breaker.
Light accumulated dust may be removed from the appliance exterior with a soft cloth or vacuum cleaner.
Wipe the exterior surfaces of the appliance occasionally with a slightly damp microfiber cloth using a solution of mild detergent and water. Dry thoroughly before operating the appliance.
The rotisserie motor is factory lubricated for life and will not require further lubrication.

WARNING! Risk of Fire! To reduce risk of fire, do not store or use gasoline or any other flammable vapors or liquids in the vicinity of the appliance.
WARNING! Risk of Electrical Shock! Any other servic-ing needed must be performed by an authorized service technician. Do not attempt to service the appliance yourself.

Cleaning
CAUTION! Do not power wash or allow water to run into the interior of the appliance as this could create a fire or electric shock. Always remove power before moving or servicing.

Glass
Dust particles can be removed by buffing lightly with a clean dry cloth. Fingerprints and other marks can be cleaned with a cloth dampened with a quality household glass cleaner. The glass should be completely dried with a lint free cloth or paper towel. Do not use abrasive cleaners on glass surface.

Metal Surface
Dust particles can be removed by buffing lightly with a clean dry cloth. A damp cloth can be used to clean painted surfaces. Do not use abrasive cleaners or chemical household cleaners. Do not spray liquids directly on to any surface.

Servicing
Except for cleaning, an authorized service technician should perform any other service.

Resetting Appliance GFCI Cord
If the Appliance GFCI power cord is tripped and there is no power to the appliance, it must be reset by pressing the “RESET” button on the GFCI plug. See Figure 6.1.

GLASS AND GLASS GASKET
It is normal during temperature changes for condensation to form on the appliance viewing glass. This may require the glass to be occasionally removed for cleaning the interior side of the glass. See section 4.B for glass remov- al instructions and refer to section 6.B for a suggested cleaning method.
While removing and replacing the front viewing glass, caution should be taken to ensure the glass gasket re-mains in place on the appliance.
Before re-installing the front viewing glass, ensure the glass gasket is fully seated and not blocking the bottom glass channel. If the gasket is protruding into the channel the glass may not fully seat and could cause interference when re-installing the glass.
If the glass gasket becomes separated from the appliance gasket channel it must be reinstalled by pressing the gas-ket back into the glass gasket channel of the appliance. If the gasket is damaged or becomes unusable contact your dealer for a replacement.
WARNING! Risk of Electrical Shock! Do Not Open! No user serviceable parts inside. Always turn appliance off and disconnect power before performing maintenance, service, or removal from the framed wall opening.

SimpliFire Troubleshooting Guide

Symptom	Possible Cause	Corrective Action
Circuit breaker trips or fuse blows when appliance is turned on	Exceeding

current rating of the circuit breaker or fuse, perhaps from operating other appliances on the same circuit as the appliance| ****

Install appliance onto a dedicated 15 amp circuit.

Lights in room dim while the

appliance is on

| Appliance is drawing close to circuit

current rating

| Install appliance onto a dedicated 15 amp circuit.

Appliance will not come on when using the manual controls on the appliance

| Appliance is not plugged into an

electrical outlet

| Ensure plug is connected to a working outlet.
Hard-wire connections not correct (if applicable)| Review wiring instructions to ensure correct connection.
No incoming power from the electrical

outlet or electrical box

| Check fuse/breaker panel.
Defect in control board (PCB)| Replace the control board (PCB).

Remote control does not work

| Low/dead batteries| Replace batteries in the remote.
Remote receiver is blocked, or remote

is not pointed directly at the receiver.

| Ensure receiver is not blocked. Move closer to the appliance.
Appliance power switch is in the off “O” position (if equipped)| Turn the power switch on, to the “I” position (if equipped).
Remote control malfunction| Replace remote control
Control board (PCB) malfunction| Replace control board (PCB).

Flame does not move at all

| Flame rotisserie motor is stalled or

malfunctioning

| Cycle appliance on or off. If problem persists inspect rotisserie and motor for blockage or interference. If no interference, replace the control board (PCB).

Flame shudder

| Flame rotisserie contacting other internal components when spinning| Ensure rod is straight and mounted properly and is spinning freely without spindles hitting other components.
Defective flame rotisserie motor| Replace flame rotisserie motor.

Fuel bed does not light up

| Fuel bed is turned off| Refer to operation section of the user manual.
Loose wiring| Check wiring to fuel bed LEDs.
Defective control board (PCB)| Replace control board (PCB).
Defective LED lights| Replace fuel bed LED lights.

Appliance turns on by itself

| Defective control board (PCB)| Replace control board (PCB).
Similar infrared signal from another remote causing appliance to turn on (pre-2019 manufactured appliances only)| Some TV remotes may cause the appliance to turn on for appliances manufactured before 2019. Replace control board (PCB).
Grinding or rubbing noise| Rotisserie hitting or rubbing against

internal components

| Replace rotisserie.

IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor.| ****

Stocked at Depot

---|---
ITEM| DESCRIPTION| COMMENTS| PART NUMBER
1| SFE Forum Crystal Media (large and small clear crystals)| | CRYSTAL-OD|
2| Black Glass Embers| | EMBER-SCION|
3| SF-OD Remote Reciver| | RECEIV-OD| Y
4| Forum Outdoor Motor| | MOTOR-OD| Y
5| PCB Board Assembly| Main & Button| PCB-OD| Y
6| Forum Outdoor Electric Remote| | REMOTE-OD| Y
7| SFE Forum OD Log Set| | LOGS-OD| Y
8| Forum OD LED Assembly| | LED-OD43| Y
9| Power Cord, Forum OD| | PLUGIN-OD| Y
10| Forum OD Accent| | ACCENT-OD43| Y
11| Forum OD Rotisserie| | ROTISS-OD43|
12| Flame Screen Forum OD| | FLAME-OD43|
13| Front for Forum OD| | FRONT-OD43|
14| Glass Bracket, Forum OD| | GLABRKT-OD43|
15| Forum Outdoor Panels| Pkg of 2| PANELS-OD|
16| Forum OD Glass Front| | GLA-OD43| Y
| Forum Outdoor Hardware Pack| | HDWR-OD|

IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor.|

Stocked at Depot

Contact Information
SimpliFire, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com
Please contact your SimpliFire dealer with any questions or concerns.
For the location of your nearest SimpliFire dealer, please visit www.simplifire.com.

– NOTES –

NOTICE
DO NOT DISCARD THIS MANUAL

Important operating and maintenance instructions included.
Read, understand and follow these instructions for safe installation and operation.
Leave this manual with party responsible for use and operation.

Printed in China – Copyright 2024
SimpliFire • SF-OD43, SF-OD55 • 2047-980 Rev. D • 2/24