BORMANN PRO BDM6700 Self Adjusting Red Laser Level Instruction Manual

BORMANN PRO BDM6700 Self Adjusting Red Laser Level

Product Specifications

• Model: BDM6700 063476
• Version: v2.2
• Languages: EN, FR, IT, EL, BG, SL, RO, HR
• Website: www.nikolaoutools.com

Product Usage Instructions

Safety and Warranty Information:
For safety and warranty validity, all repair, inspection, or replacement work must be done by technicians from the manufacturer’s authorized service department. Use the product only with the supplied equipment to prevent malfunctions or injuries.

Product Design and Technical Specifications:
The manufacturer may make minor changes to the design and technical specifications without notice unless these changes significantly affect product performance and safety. The manual may describe parts that are common across the manufacturer’s product line.

Important Notes:
Always follow the instructions in the manual for proper use of the product. Improper use may lead to malfunctions or accidents.

Frequently Asked Questions (FAQ)

• Can I use the product with equipment not provided by the manufacturer?
  It is recommended to use the product only with the equipment supplied to avoid malfunctions and potential injuries. The manufacturer is not liable for damages resulting from the use of non-conforming equipment.

• How can I ensure the validity of the warranty?
  To maintain the warranty validity, all repair, inspection, or maintenance work should be carried out by technicians from the manufacturer’s authorized service department.

• Are there specific guidelines for product maintenance?
  Refer to the manual for maintenance instructions and special adjustments. Follow these guidelines to ensure the safety and reliability of the product.

INTRODUCTION

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
• Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.

Safety warnings

• Read the Safety Instructions and Manual thoroughly before using this product. All users must fully understand and adhere to these instructions.
• While the product is in operation, be careful not to expose your eyes to the emitting laser beam. Exposure to a laser beam for an extended time may be hazardous to your eyes.
• Do not stare directly into the beam or view directly with optical instruments or set up the laser at eye level.
• Do not disassemble the laser tool. There are no user serviceable parts inside the device.
• Do not modify the laser in any way. Modifying the tool may result in hazardous Laser Radiation Exposure.
• Do not operate the laser around children or allow children to operate the laser.
• An exposure to the beam of a Class 2 laser is considered safe for a maximum of 0.25 seconds. Eyelid reflexes will normally provide adequate protection.

Description of main parts (picture A)

1. Keypad and indication light
2. Laser outlet
3. Lock switch
4. Battery case
5. 1/4’ mounting thread

Operating instructions

Before inserting the batteries, please make sure the Lock Switch is set to the position.
Always keep the Lock Switch at the position when transporting the laser level or storing it. It is very important!

Auto Self-leveling Mode:
Set the Lock Switch at the position, vertical and horizontal laser beams both light up, and the device will be self-levelled. The indication light will turn green (if the indication light turns red, and lines flash, it indicates that the lines is not levelled, please place the device on a flatter surface. The self-leveling range is about 40)

Pulse mode:

• Long-Press the key button in order to turn the pulse mode on, long-press again to turn off the pulse mode .
• Set the lock Switch at the position, in this way the laser level will turn off.

Locked Mode:
When the Lock Switch is set at the position, long-press the key button, then the vertical and horizontal laser beams both light up and flash every 5 seconds, the indication light will turn red. Long time press the key button, to switch it off.

Power saving mode:
When the instrument is working, short-press the key button, the instrument enters the energy-saving mode, and the brightness is reduced to about 80% of the maximum brightness; press it once again to reduce it to 65%; press it again to reduce it to 50%; press again to restore the maximum brightness cyclically.

Technical Data

Maintenance

• The laser tool is sealed and calibrated at the factory to the specified accuracy.
• It’s recommended to carry out an accuracy check before the first use and periodic checks during future use especially for precise layouts.
• Do not short any battery terminals or charge alkaline batteries or dispose of batteries in fire.
• Do not combine old and new batteries. Replace all of them at the same time use new batteries of the same brand and type.
• Keep batteries out of reach of children.
• Remove batteries if the tool will not be used for several months.
• Do not store the laser tool in direct sunlight or expose it to high temperatures. The housing and some internal parts are made of plastics and may become deformed at high temperatures.
• Exterior plastic parts may be cleaned with a damp cloth. Although these parts are solvent resistant, NEVER use solvents. Use a soft, dry cloth to remove moisture from the tool before storage.
• Do not dispose of this product along with household waste.
• Always dispose of batteries per local code.

WARRANTY

The electrical appliances have been manufactured according to strict standards, set by our company, which are aligned with the respective European quality standards. The electrical appliances of our company are provided with a warranty period of 24 months for non-pro-fessional use and 12 months for professional use. The warranty is valid from the date of pur-chase of the product. Proof of the warranty right is the purchase document of the appliance (retail receipt or invoice). Under no circumstances shall the company cover the relevant cost of spare parts and respective required working hours unless a copy of the purchase document is presented. In case the repair has to be done by our service department the cost of transportation (to and from) is entirely borne by the sender (client). The electrical appliances must be sent for repair to the company or to an authorized workshop in the appropriate way and means of transport.

WARRANTY EXEMPTIONS AND RESTRICTIONS:

1. Spare parts that wear out naturally as a consequence of being used (brushes, cables, switches, chargers, chucks etc.).
2. Electrical appliances damaged as a result of non-compliance with the instructions of the manufacturer.
3. Electrical appliances poorly maintained.
4. Use of inappropriate accessories.
5. Electrical appliances given to third entities free of charge.
6. Damage due to an electrical connection at a voltage other than that indicated on the appliance plate.
7. Connection to a non-earthed power supply.
8. Change in current voltage.
9. Damage resulting from the use of salty water.
10. Damage or malfunction resulting from improper cleaning procedure of the appliance.
11. Contact of the electrical appliance with chemicals, or damage as a result of moisture or corrosion.
12. Electrical appliances that have been modified or opened by unauthorized personnel.
13. Broken parts/components as a result of inappropriate use.
14. Electrical appliances used for rent.
    The warranty covers only the free of charge replacement of the component that presents a manufacturing defect or material failure. In case of lack of a specific spare part the company reserves the right to replace the electrical appliance with another corresponding model. After all warranty procedures have been concluded, the warranty period of the electrical appliance shall not be extended or renewed. Τhe replacement of a spare part, along with repair charge, is covered by a 1 year warranty of good operation, provided that the warranty terms are met. The spare parts or electrical appliances that are replaced remain in the pos-session of our company. Requirements, other than those mentioned in this warranty form, regarding the repair of electrical appliances or damage thereof, do not apply. Greek law and relative regulations apply to this warranty.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>