Interthings IPB203 Doorbell Camera User Guide
- June 16, 2024
- Interthings
Table of Contents
Interthings IPB203 Doorbell Camera User Guide
Package contents
- 1x Doorbell camera 1x Indoor chime
- 1x USB charging cable
- 1x Installation set
- 1x Reset pin
- 1x Quick Start Guide
Description
**Doorbell
**
- Microphone
- Lens
- Light sensor
- Indicator red- charging blue – working
- Doorbell button
- Reset button
- Hold and press the reset button for 3 seconds to reset the connection and delete the device from the app.
- Speaker
- Screw hole (for install the doorbell and wall bracket)
- Type-C charging port
**Chime
**
- Indicator
- Speaker
- Pairing button
- Voice +/-
- Tune
- USB 2.0 power connector
Before using the doorbell
-
Charge the doorbell device via a 5V(1A~2A) adaper (adapter not included) and suplied charging cable.
While the doorbell is in charging, the charging indicator(red) will be turnned on.
The charging indicator will be turnned of automatically while the battery is fully charged. -
Before mounting the doorbell, use your smartphone to test if the Wi-Fi signal be covered and strong signal. Place the camera in a location with a clear, unblock field of view.
Pair the chime and doorbell
- Plug-in the USB chime in to a 5V(1A ~2A) adapter or a USB 2.0 socket to power on the chime.
- Hold and press the A-pair button of the chime , the indicator of the chime will be flashed which means the chime is ready to pair.
- Press the B-ring button of the doorbell camera, the chime will receive the signal and ring, means the chime is connected to the doorbell camera.
- Press the voice +/- button to switch the volume of the chime.
- Press the tune button to choose your desired tune
Installation – Connect the doorbell with the app
- Power the camera After full charge the battery, hold and press the bell button for 3 seconds to turn on the doorbell.
- App setup and installation Use your mobile phone or tablet to search for “TuyaSmart” or “Smarties” in Google Play (for Android OS) or in the Apple app store (for iOS) to find the app, and install it according the instructions.
TuyaSmart
Smart Life
Register an account
‘If this is the first time using the app, you need to register an account as per below:
Note :
- Make sure your smartphone already connected to a 2.4GHz Wi-Fi and the Bluetooth turns ON.
- Press the ring button of the doorbell, then tap “scan” or “Smart camera(BLE)” from the app.
Ring the bell make sure the blue indicator is blinking.
The device only works when someone rings the bell.
User will get the notification and phone call from the app.
The message center helps user to check the history of the visitors.
Q: Camera will not connect to my Wi-Fi network?
A: Make sure the Wi-Fi signal is flashing. If the Wi-Fi signal is not flashing, you will need to press and hold Reset Button located at the back of the camera(see the Description section). - Make sure the Wi-Fi network is a 2.4GHz network, device will not connect to a 5GHz network. - Test your Wi-Fi network work with other devices such as your phone or computer to make sure it is operation properly. - The Wi-Fi connection may be out of range during pairing. Use your phone to check range, it is recommended to have at least 2 signal bars showing for proper connection. - Your Wi-Fi network password is case sensitive, make sure you are entering it correctly.
Q: The camera is o-line
A: - Charing the doorbell and try again, to check if it is because of low batery. -There may be a temporary issue with your internet connection (e.g., service disruption). Please try again in a few minutes. - Make sure your Wi-Fi router is turned On. - The camera may not have power to it, make sure the wall switch and breaker is in the On position. - Make sure the camera is getting a good signal from your Wi-Fi router. Use your phone to check range, it is recommended to have at least 2 signal bars showing for proper connection. The camera may have been disconnected from your Wi-Fi network, press and hold Reset Button(see the Description section) until you hear an audible tone.
Warning
To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the user’s authority to operate this equipment.
FCC Statement
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>