SEMI-PRIVACY HORIZONTAL
PERIMETER GATE

Horizontal Semi Privacy Perimeter Gate

COMPONENTS

A. Unassembled Gate (Qty 1)
1. Vertical U Channel Posts (Qty 2)
2. Horizontal U Posts (Qty 2)
3. Square-Edge Boards (Qty 4)
4. Hardware 3.5 in Screws (Qty 4)
5. “L” Support Angle (Qty 4)
6. Chicago Screws (Qty 8)
7. Spacers (Qty 6)
B. Hinge Set (Qty 2)
C. Latch Set (Qty 1)
D. Top Cab Pack (Qty 4)
ADDITIONAL COMPONENTS
A. 5X5 Composite Post (Qty 2)
B. 5X5 Post Cap Horse/Estate (Qty 2)
Modern Full-Size Gate
INSTALLATION GUIDELINE

GATE COMPONENTS

1. Vertical U-Channel Posts (Qty 2)
2. Horizontal U Posts (Qty 2)
3. Square-Edge Boards (Qty 4)
4. Hardware 3.5 in Screws (Qty 4)
5.  Horizontal T Frame (Qty 2)
6. Frame Extension (Qty 2)

BEFORE YOU BEGIN

• Verify the location of all underground utilities
  o Aids: Local building departments, utility companies, or utility location service at 811

• Locate property line

• Consult with HOA, if applicable, and follow CC&Rs Guidelines

• Consult local and regional building codes

• Obtain all necessary permits as required by building codes

TOOLS REQUIRED
Gate Assembly

• Phillips Screwdriver (No. 3)
  Gate Installation

• 2 Torque Head Driver/Drill Bit

• Drill or Impact Driver

• Tape Measure
  Post 5×5 Installation

• Wheelbarrow

• Post Hole Digger and Shovel

• Level and String Line

• Stakes or Markers

LAY OUT FENCE LOCATION
Gates are sold at 45.5″ wide, for a 48.6″ opening.

1. Using stakes and a string line, mark out the fence location.
2. Locate gate placement and mark post hole locations for the gate posts accordingly. The Gate opening should be 48.6″ wide.
3. Mark the locations of corners and ends of the fence.
4. Mark locations of intermediate fence posts between ends, corners and gate posts. Post should be located no wider than 69″ (5.75′) apart for each fence panel.

TOOLS REQUIRED
Gate Assembly

• Phillips Screwdriver (No. 3) Gate Installation

• 2 Torque Head Driver/Drill Bit

• Drill or Impact Driver

• Tape Measure
  Post 5×5 Installation

• Wheelbarrow

• Post Hole Digger and Shovel

• Level and String Line

• Stakes or Markers

GATE ASSEMBLY

2.1 Install “L “Support Angle

1. Join the Vertical and Horizontal U channels with the “L” support angle and the Chicago Screws.

BOARD ASSEMBLY INSIDE FRAME

1. The boards length will fit the inside of the gate frame.
2. Start with the bottom and Upper Square-Edge Board and end with the middle board of as shown in the video.

2.5 INSTALL HINGES AND LATCH.
1. 1. Follow hinge and latch installation guides
2.6 TOP CAP INSTALLATION

1. Slide the Top Cap into the Top Cap Routed space on the top of the U-Channel post.
2. Fix into positions using one (1) 1-3/4” Composites Screw and a drill.
3. Repeat for all U-Channel Posts.

GATE POST SUPPORT

3.1 INSTALL 5X5 POST ON THE GROUND

1. Prepare the ground to insert posts by digging 12 inches diameter holes.
2. Make sure to check with your local utility providers to confirm where underground pipes and cables are before you start digging.

Connecting Fence Panel to Ranch Rail posts

Documents / Resources

| Natures Composites Horizontal Semi Privacy Perimeter Gate [pdf] Owner's Manual
Horizontal Semi Privacy Perimeter Gate, Semi Privacy Perimeter Gate, Privacy Perimeter Gate, Perimeter Gate, Gate
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>