MinebeaMitsumi Smart Lighting Node Hybrid NEMA Instructions
- June 3, 2024
- MinebeaMitsumi
Table of Contents
MinebeaMitsumi Smart Lighting Node Hybrid NEMA
Warnings
The following instructions provide important precautions to safely install,
use and maintain the product.
Please read and follow them carefully before operating the unit: failure to
comply may compromise people safety and/or damage the device, with serious
consequences depending on circumstances.
- The equipment is Class II equipment and fits outdoor installation. It does not require (and must not have) a safety connection to electrical earth.
- The equipment is intended for installation, service and repair by trained and skilled personnel only (no operator access)
- Install the product in accordance with the instructions provided in this installation manual
- The manufacturer shall not be held liable for errors or damages due to wrong mounting operations
- This equipment is intended to be used with elevations up to 2000 m
- The product and the various units comprising the installation must only be used for the purpose for which they are intended. Any other use is considered improper and dangerous
- Unpack the product and check possible damages before installing and operating it
- Electrical work and installation must be performed in accordance with relevant local and national regulations, following the instructions provided in this installation manual.
- Before connecting the product, make sure that product voltage ratings correspond to the mains power supply voltage
- Product drivers are default set as per the configuration sheet provided with the product. The product must only be installed in luminaires with compatible drivers.
- When plugging the product on the luminaire socket, ensure that the North indicator on the cap is aligned with the North indicator of the luminaire socket.
- Install the product under a good GPS coverage.
- Before cleaning or servicing the product, disconnect it from the mains power
- Dispose of packaging or product must be in compliance with applicable local and national waste disposal regulation
- Keep this document for future use and reference
RF exposure information
The NDLM007US (FCC ID: 2AKPQNDLM007) complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept all interference received, including interference that may cause undesired operation
This device should be operated with a minimum separation distance of 50 cm
between the equipment and a person’s body.
The calculations were carried out assuming no co-location or operation in
conjunction with any other antenna or device which may contain transmitters.
The equipment contains:
NDLM007US-1, FCC ID: N7NWP77B NDLM007US-2, FCC ID: N7NWP76B
RF exposure guidelines for addressing co-location
The device should not be co-located with any other transmitter during the installation without following the FCC co-location procedure first (FCC KDB 447498 RF exposure guidelines for addressing co-location).
US Responsible party
NMB Technologies Corporation, 9730 Independence Ave, Chatsworth, CA 91311, United States
Changes
Changes or modifications made to this equipment not expressly approved by MinebeaMitsumi inc., may void the user’s authority to operate this equipment.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- ease the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This radiocommunication equipment has electromagnetic field strength in compliance with the Safety Standard for the Use of Radiocommunication Equipment on Human Health announced by the National Telecommunications Commission.
Smart Lighting Node Hybrid NEMA
Part No. NDLM007US-1
Serial No. 002105280001
Production date: 2022-05-04
Interfaces MAC addresses
Narrowband MAC address: xxxxxxxxxxx
Bluetooth MAC address: xxxxxxxxxxx
Software packages versions
Linux Image: xxx
Backend: xxx
Radio FW: xxx
LTE module info
Model: WP7702
Modem IMEI: xxx
eSIM info
eSIM ICCID: xxx
Installation procedure
When plugging the Hybrid NEMA 5G into the luminaire socket, ensure that the North indicator on the cap is aligned with the North indicator of the luminaire socket, as shown the figure below.
Once plugged into the luminaire socket, rotate the cap of the product clockwise until it is safely locked in the final position. In order to avoid mechanical stress, please do not rotate the device with excessive force.
Before the installation
Before the installation, the installer/user must read the full manual available at the following internet address upon registration at the Paradox Engineering website:
MinebeaMitsumi Inc.
3-9-6 Mita, Minato-ku,
Tokyo 108-8330
Phone: +81-03-6758-6711
www.minebeamitsumi.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>