Natures Composites Horizontal Semi Privacy Full Size Gate

Specifications

• Product: Composite Modern Horizontal Semi-Privacy Full Size Gate
• Gate Width: 45.5 inches
• Gate Opening: 48.6 inches
• Post Size: 5×5 Composite Post

Product Usage Instructions

Before You Begin:
Ensure the ground is level and free from any obstructions that may hinder installation due to moisture.

Lay Out Fence Location

1. Using stakes and a string line, mark out the fence location.
2. Locate gate placement and mark post hole locations for the gate posts accordingly. The gate opening should be 48.6 inches wide.
3. Mark the locations of corners and ends of the fence.
4. Mark locations of intermediate fence posts between ends, corners, and gate posts. Posts should be located no wider than 69 inches (5.75 feet) apart for each fence panel.

Tools Required

• Post Hole Digger
• Level
• Spacers
• Phillips Screwdriver (No. 3)

Gate Assembly

Frame Assembly

1. Insert the Horizontal T Frame into the Frame Extension to ensure a precise fit.
2. Firmly press the two parts together until they fit completely together.
3. Place the assembled frame inside the U-Channel posts.
4. Ensure the frame is level and properly positioned.

T &G Board Assembly Inside Frame

1. The boards’ length should fit inside the gate frame.
2. To ensure consistent spacing between boards, use spacers to maintain uniform gaps between each board.

Composite Posts Assembly

1. Place each post to enclose the frame.

Secure the Gate Using Screws

1. Attach the frame to the post using the included screws at each corner with a Phillips Screwdriver (No. 3).

Install Hinges and Latch

1. Follow the separate instruction guide for installing hinges and latch.

Hanging the Gate

1. The gate can be hung on either an NC 5×5 post or an existing post. Ensure that the post can support the gate’s weight.

Top Cap Installation

1. Slide the Top Cap into the Top Cap Routed space on the top of the U-Channel post.
2. Secure it in place using a composite screw and a drill. Repeat for all U-Channel Posts.

Gate Post Support

Install 5×5 Post on the Ground:

1. Posts recommended to be 9 feet long with 3 feet in the ground.
2. Dig 12-inch diameter holes in the ground to insert posts, ensuring there are no underground pipes or cables in the way.

Frequently Asked Questions (FAQ):

• Q: Can the gate be installed on uneven ground?
  A: It is recommended to install the gate on level ground to ensure proper alignment and function.

• Q: How do I adjust the gate if it doesn’t close properly?
  A: Check if the gate is level and adjust as needed. Ensure hinges are properly installed and latch is functioning correctly.

COMPOSITE MODERN HORIZONTAL SEMI-PRIVACY FULL SIZE GATE
INSTALLATION GUIDE

Dimension

COMPONENTS

• Unassembled Gate (Qty 1)
  1. Vertical U Channel Posts (Qty 2)
  2. Horizontal U Posts (Qty 2)
  3. T&G Boards (Qty 8)
  4. Hardware 3.5 in Screws (Qty 4)
  5. Horizontal T Frame (Qty 2)
  6. Frame Extension (Qty 2)
• Hinge Set (Qty 2)
• Latch Set (Qty 1)
• Top Cab Pack (Qty 4)

ADDITIONAL COMPONENTS

• 5X5 Composite Post (Qty 2)
• 5X5 Post Cap Horse/Estate (Qty 2)

HORIZONTAL SEMI-PRIVACY FULL SIZE GATE

INSTALLATION GUIDELINE

GATE COMPONENTS

1. Vertical U-Channel Posts (Qty 2)
2. Horizontal U Posts (Qty 2)
3. T&G Boards (Qty 8)
4. Hardware 3.5 in Screws (Qty 4)
5. Horizontal T Frame (Qty 2)
6. Frame Extension (Qty 2)

BEFORE YOU BEGIN

• Verify the location of all underground utilities
  • Aids: Local building departments, utility companies, or utility location service at 811
• Locate property line
• Consult with HOA, if applicable, and follow
• CC&Rs Guidelines
  • Consult local and regional building codes
  • Obtain all necessary permits as required by building codes
  • Always wear appropriate safety equipment
  • Store product on a flat service in a dry place away from moisture

LAY OUT FENCE LOCATION

Gates are sold at 45.5″ wide, for a 48.6″ opening

1. Using stakes and a string line, mark out the fence location.
2. Locate gate placement and mark post hole locations for the gate posts accordingly. The Gate opening should be 48.6″ wide.
3. Mark the locations of corners and ends of the fence.
4. Mark locations of intermediate fence posts between ends, corners and gate posts. Post should be located no wider than 69″ (5.75′) apart for each fence panel.

TOOLS REQUIRED

Gate Assembly

• Phillips Screwdriver (No. 3)

Gate Installation

• 2 Torque Head Driver/Drill Bit

• Drill or Impact Driver
• Tape

Measure Post 5×5
Installation

• Wheelbarrow
• Post Hole Digger and Shovel
• Level and String Line
• Stakes or Markers

GATE ASSEMBLY

FRAME ASSEMBLY

1. Insert the “HORIZONTAL T FRAME” into the “FRAME EXTENSION” to ensure a precise fit.
2. Firmly press the two parts together until they fit completely together.
3. Place the assembled frame inside the U-Channel posts.
4. Make sure the frame is level and properly positioned.

COMPOSITE POSTS ASSEMBLY

1. Place each post to enclose the frame.

T &G BOARD ASSEMBLY INSIDE FRAME

1. The boards length will fit the inside of the gate frame.
2. To ensure consistent spacing between boards, position the first board in the desired location, place spacers on each side of it to create the necessary gap for expansion, then place the next board tightly against the spacers. Repeat this process for each subsequent board, always using spacers to maintain uniform gaps.

SECURE THE GATE USING THE SCREWS (INCLUDED) INTO EACH CORNER

1. Please use the included screw to attach the frame to the post to keep it fixed in place in each corner.

INSTALL HINGES AND LATCH
Follow separate instruction guide for Hinges and Latch.

HANGING THE GATE

1. This gate can be hung on either an NC 5×5 post or an existing post. If hung on an existing post, it is recommended that the customer ensures the post has the necessary strength to support the weight of the gate.

TOP CAP INSTALLATION

1. Slide the Top Cap into the Top Cap Routed space on the top of the U-Channel post.
2. Fix into positions using one (1) 1-3/4” Composites Screw and a drill.
3. Repeat for all U-Channel Posts.

GATE POST SUPPORT

INSTALL 5×5 POST ON THE GROUND

1. Posts recommended to be 9 feet long to have 3 feet in the ground
2. Prepare the ground to insert posts by digging 12 inches diameter holes.
3. Make sure to check with your local utility providers to confirm where underground pipes and cables are before you start digging.

CONNECTING FENCE PANEL TO 5×5 POSTS

Screw the U Chanel fence post to the 5X5 Post

1. Space screws evenly from top of U-Channel post to bottom to secure to 5×5 Post.

Bury the posts together

Documents / Resources

| Natures Composites Horizontal Semi Privacy Full Size Gate [pdf] Installation Guide
Horizontal Semi Privacy Full Size Gate, Horizontal, Semi Privacy Full Size Gate, Privacy Full Size Gate, Full Size Gate, Size Gate, Gate
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>