Natures Composites HORIZONTAL Modern Full-Size Gate

Specifications

• Modern Full-Size Gate
• Patented NC system with two ground clearance options
• Gate opening width: 48.6 inches
• Includes various components for assembly

Product Usage Instructions

Installation Guidelines

Before You Begin:

• Check local codes and regulations before installation.
• Ensure you have all the necessary tools ready.

Tools Required:

• Stakes and string line
• Drill
• Screws

Gate Assembly

Frame Assembly

1. Insert the Horizontal T Frame into the Frame Extension.
2. Firmly press the parts together for a precise fit.
3. Place the assembled frame inside the U-Channel posts, ensuring it is level and positioned correctly.

T &G Board Assembly Inside Frame

1. Fit the T&G boards inside the gate frame, starting with the bottom and upper boards and ending with the middle board.

Composite Posts Assembly

1. Enclose the frame with the composite posts.

Secure the Gate Using Screws

Please use the included screws to attach the frame to the posts securely in each corner.

Install Hinges and Latch

Follow the provided hinge and latch installation guides for proper installation.

Hanging the Gate

The gate can be hung on a 5×5 post or an existing post. Ensure the post is strong enough to support the gate’s weight.

Top Cap Installation

1. Slide the Top Cap into the designated space on top of the U-Channel post.
2. Secure it in place using composite screws and a drill. Repeat for all posts.

Gate Post Support

Install 5×5 Posts on the Ground

1. Dig 12-inch diameter holes for the posts, ensuring no underground pipes or cables are damaged.

Connecting Fence Panel to 5×5 Posts

The patented system offers two ground clearance options (2 inches or 3.5 inches) for connecting fence panels to posts.

FAQ

• Q: Can the gate be installed on an existing post?
  • A: Yes, the gate can be hung on either a 5×5 post or an existing post, but make sure the existing post is strong enough to support the gate’s weight.
• Q: What is the recommended ground clearance for connecting fence panels?
  • A: The patented system offers two options – 2 inches or 3.5 inches of ground clearance for connecting fence panels to 5×5 posts.

COMPONENTS

• A. Unassembled Gate (Qty 1)

  1. Vertical U Channel Posts (Qty 2)
  2. Horizontal U Posts (Qty 2)
  3. T&G Boards (Qty 5)
  4. Hardware 3.5 in Screws (Qty 4)
  5. Horizontal T Frame (Qty 2)
  6. Frame Extension (Qty 2)

• B. Hinge Set (Qty 2)

  • C. Latch Set (Qty 1)

• D. Top Cab Pack (Qty 4)
  ADDITIONAL COMPONENTS

  • A. 5X5 Composite Post (Qty 2)
  • B. 5X5 Post Cap Horse/Estate (Qty 2)

Modern Full-Size Gate

INSTALLATION GUIDELINE

GATE COMPONENTS

1. Vertical U-Posts (Qty 2)
2. Horizontal U Posts (Qty 2)
3. T&G Boards (Qty 10)
4. Hardware 3.5 in Screws (Qty 4)
5. Horizontal T Frame (Qty 2)
6. Frame Extension (Qty 2)

BEFORE YOU BEGIN

• Verify the location of all underground utilities
  • Aids: Local building departments, utility companies, or utility location service at 811
• Locate property line
• Consult with HOA, if applicable, and follow CC&Rs Guidelines
• Consult local and regional building codes
• Obtain all necessary permits as required by building codes

TOOLS REQUIRED

• Gate Assembly
  • Phillips Screwdriver (No. 3)
• Gate Installation

  • 2 Torque Head Driver/Drill Bit

  • Drill or Impact Driver
  • Tape Measure
  • Post 5×5 Installation
• Wheelbarrow
  • Post Hole Digger and Shovel
  • Level and String Line

LAY OUT FENCE LOCATION

Gates are sold at 45.5″ wide, for a 48.6″ opening

1. Using stakes and a string line, mark out the fence location.
2. Locate gate placement and mark post hole locations for the gate posts accordingly. The Gate opening should be 48.6″ wide.
3. Mark the locations of corners and ends of the fence.
4. Mark locations of intermediate fence posts between ends, corners, and gate posts. The post should be located no wider than 69″ (5.75′) apart for each fence panel.

GATE ASSEMBLY

FRAME ASSEMBLY

1. Insert the “HORIZONTAL T FRAME” into the “FRAME EXTENTION” to ensure a precise fit.
2. Firmly press the two parts together until they fit completely together
3. Place the assembled frame inside the U-Channel posts.
4. Make sure the frame is level and properly positioned.

T &G BOARD ASSEMBLY INSIDE FRAME

1. The boards length will fit the inside of the gate frame
2. Start with the bottom and upper T&G board and end with the middle board of as shown in the video

T&G BOARD ASSEMBLY INSIDE FRAME\

COMPOSITE POSTS ASSEMBLY

SECURE THE GATE USING THE SCREWS (INCLUDED) IN TO EACH CORNER

1. Please use the included screw to attach the frame to the post to keep it fixed in place in each corner.

INSTALL HINGES AND LATCH

1. Follow hinge and latch installation guides

HANGING THE GATE

1. This gate can be hung on either a 5×5 post or an existing post. If hung on an existing post, it is recommended that the customer ensures the post has the necessary strength to support the weight of the gate.

TOP CAP INSTALLATION

1. Slide the Top Cap into the Top Cap Routed space on the top of the U-Channel post.
2. Fix into positions using one (1) 1-3/4” Composites Screw and a drill.
3. Repeat for all U-Channel Posts.

GATE POST SUPPORT

INSTALL 5×5 POSTS ON THE GROUND

1. Prepare the ground to insert posts by digging 12-inch diameter holes.
2. Make sure to check with your local utility providers to confirm where underground pipes and cables are before you start digging.

Connecting fence panel to 5×5 posts

Documents / Resources

| Natures Composites HORIZONTAL Modern Full Size Gate [pdf] Instruction Manual
PRIVACY_HORIZONTAL_GATE_PERIMETER, HORIZONTAL Modern Full Size Gate, HORIZONTAL, Modern Full Size Gate, Full Size Gate, Gate
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>