ROLL-A-SHADE CA 92503 Anodized Roller Shade Cassette System Installation Guide

: September 12, 2024
: ROLL-A-SHADE

Table of Contents

CA 92503 Anodized Roller Shade Cassette System
Specifications
Product Usage Instructions
1. Release Tab and Bottom Hooks
2. Install Bracket
3. Mount the Headrail
4. Shade Adjusting
5. Install Plastic Connectors or Metal Stop Ball to Bead
6. Install the Chain Anchor
- FAQ
Q: What should I do if the material tracks to one side?
Q: How should I set the shade height?
Q: Why is the tension device important?

CA 92503 Anodized Roller Shade Cassette System

“`html

Specifications

Manufacturer: Rollashade
Product: Sun Control Solutions
Hardware Included: Self Tapping Screws, Plastic Connectors,
Brackets
Tools Required: Drill, 1/4 Hex Head Phillips Head, Self Tapping
Phillips Screws, Wood Screws, Metal Stop Ball

Product Usage Instructions

1. Release Tab and Bottom Hooks

Ensure the release tab is at the top and the bottom hooks are at
the bottom.

2. Install Bracket

Attach brackets to the window frame or wall with a minimum 0.25″
gap to any perpendicular surface.

3. Mount the Headrail

Position the headrail on brackets ensuring a secure fit by
snapping the groove into place.

4. Shade Adjusting

Roll shade up and down to ensure bottom rail is level. Adjust by
adding masking tape to the metal tube if needed.

5. Install Plastic Connectors or Metal Stop Ball to Bead

Chain

Attach connectors or stop balls to set desired shade height.

6. Install the Chain Anchor

Use the tension device to prevent accidents involving cords and
chains. Follow installation instructions carefully.

FAQ

Q: What should I do if the material tracks to one side?

A: Lower the shade until you see the metal tube and add layers
of masking tape to correct the tracking direction.

Q: How should I set the shade height?

A: Use plastic connectors or metal stop balls on the bead chain
to adjust the shade height accordingly.

Q: Why is the tension device important?

A: The tension device is crucial for safety to prevent accidents
involving cords and bead chains, especially with young children
around.

“`

MANUFACTURING SUN CONTROL SOLUTIONS

12101 Madera Way, Riverside, CA 92503 · 951-245-5077 · Fax: 951-245-5075 7240 Woodbine Ave. Suite 215 Markham, ON. L3R 1A4 · 888-245-5077 · Candian Sales Office

Cassette Installation Instructions

Hardware Included

Self Tapping Screws

for Aluminum

Plastic

Connectors

Brackets

Tools Required
Drill 1/4″ Hex Head Phillips Head

Self Tapping Phillips Screws for
Tension Device
Wood Screws (If Requested)

or
Metal Stop Ball

1. Release Tab and Bottom Hooks
Make sure the release tab is always mounted on the top and the bottom hooks are on the bottom.

4. Shade Adjusting (If Necessary)
Roll shade up and down to confirm bottom rail is level and material rolls up straight on center tube. If the bottom rail is not level, lower shade until you see the metal tube. Add layers of masking tape to the metal tube to the end that is too low until bottom rail is straight. If the material tracks to one side, lower shade until you see the metal tube. Add layers of masking tape to the metal tube to the end that is opposite the direction of tracking, until shade rolls up straight.
Masking Tape

Release Tab
Bottom Hooks
2. Install Bracket
Attach the brackets to the window frame, window molding, wall or ceiling with a minimum .25″ gap to any perpendicular surface per diagrams. Two screws must be installed in each bracket as shown.

5. Install Plastic Connectors or Metal Stop Ball to Bead Chain
Pull the rear chain to lower the shade to appropriately 1/4″ above sill and attach connector or stop ball to upper most bead on front chain closest to the clutch. By attaching this connector or stop ball you will set how far the shade will lower. Pull the front chain and raise the shade so the bottom rail is 5″ below the shade and attach a connector or stop ball on the back chain at upper most bead.

OR

.25″ Gap Minimum Wall or Outside Mount

.25″ Gap Minimum Inside or Ceiling Mount

3. Mount the Headrail
Position the headrail with the back panel (A) resting on both bottom hooks of all brackets. Push the front of the headrail firmly upwards and toward the window until the groove at the top of the headrail snaps into place, (B) as shown.
B

Plastic Bottom
Stop
Metal Bottom
Stop

Plastic Top Stop
OR
Metal Top Stop

A

www.rollashade.com

Rev:02.10.21

6. Install the Chain Anchor
The chain anchor is a plastic piece that is attached to the chain to secure it from possible accidents. Position the chain anchor on the window frame so that the chain anchor and chain do not interfere with raising or lowering the shade. The chain anchor should be installed without stretching or pulling down on the chain. Leave a little play through the chain anchor to allow the chain to pass freely. Do not twist or cross the bead chain. Secure the anchor with Phillips screws in both upper and lower holes.
Warning: Failure to use the tension device may cause injury or death.

WARNING
Young children can STRANGLE in cord and bead chain loops. They can also wrap cords around their necks and STRANGLE. = Always keep cords and bead chains out of
children’s reach. = Move cribs, playpens, and other furniture away
from cords and bead chains. Children can climb furniture to get to cords. = Attach tension device to wall or floor. This can prevent children from pulling cords and bead chains around their necks. Fasteners provided with the tension device may not be appropriate for all mounting surfaces. Use appropriate anchors for the mounting surface conditions.

www.rollashade.com

Rev: 02.10.21

TENSION DEVICE
INSTALL ATION INSTRUCTIONS
Rollashade.com info@rollashade.com 951.245.5077
© Copyright Roll-A-Shade® Inc. All Rights Reserved.

HARDWARE INCLUDED

Tension Device + Chain

Tension Device Bracket

Short Screws

Screws

INSIDE OR OUTSIDE APPLICATION

OUTSIDE INSIDE

TOOLS REQUIRED 3/8″ Hex Head Phillips Head 1/8″ Drill Bit
Drill

INSIDE

OUTSIDE

INSIDE MOUNT & TENSION DEVICE INSTALLATION Pull the Chainhold down until the chain is fully tensioned (plunger will be fully raised). Screw device into wall.

A

B

KEEP TENSION

C
SECURE TENSION DEVICE

NOTE: Please make sure shade operates smoothly.

OUTSIDE MOUNT & TENSION DEVICE INSTALLATION
With provided screws, install bracket first with large screws (use Chainhold marked screw hole locations as reference). Pull the Chainhold down until the chain is fully tensioned (plunger will be fully raised). Install Chainhold into bracket with small screws.

A

B

PULL CHAIN DOWN & MARK LOCATION
C

REMOVE TENSION DEVICE & DRILL
D

E
PLACE TENSION DEVICE ON BRACKET

F
SECURE TENSION DEVICE

NOTE: Please make sure shade operates smoothly.
RASTDV2VER.2 4 OF 4 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.