ROLL-A-SHADE QOQMGM12P3 Sun Sensor Eclipse Instruction Manual
- June 5, 2024
- ROLL-A-SHADE
Table of Contents
QOQMGM12P3 Sun Sensor Eclipse
Instruction Manual
RAS – Installation Instructions Sun Sensor Eclipse
A. Reawaken From Sleep Mode
- Use a Paper Clip to press the reset button
- Check for Battery level on the screen. If low use a USB charger to fully charge.
B. Enable and Set Time
-
Make sure Sun Sensor is enabled to detect the sun.
If enabled, you will see sun and number on the menu screen. Go to step 2.
Note: USB is
only for charging and NOT to be kept in when mounting.
-
The final step in programming is to set a date and time.
a. Configuration > Date and Time
-
The Eclipse is now ready to be mounted into the window.
Note: Do NOT leave USB plugged into sensor when mounted.
C. Install Bracket
-
Install Sun Sensor bracket into mullion vertically or horizontally.
Note: Must be at least two screws in every bracket.
-
Install Sun Sensor into the bracket
Note: Must be at least two screws installed into Sun Sensor.
Note 2: Make sure the screen and buttons are facing you.
-
Sun Sensor installation check.
Note: Make sure all screws are securely fastened into the bracket and Sun Sensor.
-
Test Sun Sensor
Note: The device is designed for interior installations only.
****
| 
---|---
Sun Sensor External Instructions
D. Roll-A-Shade Eclipse Pairing:
WHEN SHADES ARE NOT PAIRED
-
To pair shades to Eclipse, go to Main Menu > Shade Pairing > Pair with shade > Make sure shade is on > Either press button on motorhead > shade will jog to show completely.
a. Shades will now be paired
-
Make sure Sun Sensor is enabled to detect the sun.
If enabled, you will see sun and number on the menu screen. Go to step 3.
-
The final step in programming is to set a date and time.
a. Configuration > Date and Time
Once completed press back
4x -
The Eclipse is now ready to be mounted into the window.
Note: Do NOT leave USB plugged into sensor when mounted.
E. Somfy Eclipse Pairing:
WHEN SHADES ARE NOT PAIRED
WHEN SHADES ARE NOT PAIRED BUT YOU HAVE A REMOTE TRANSMITTER
-
Use your remote or wall switch to put shades in programming mode.
a. Press the programming button on the back of the remote with a paperclip until the shade jogs.
b. QUICKLY switch to Eclipse and go all the way to the left to copy and paste the programming into the eclipse.
i. Main Menu>Shade Pairing>Manual> Use Up, Down, Stop to control the shade.
Right for Prog. Left to exit.
(Motor will jog when paired)
c. The shades are now paired. -
Make sure Sun Sensor is enabled to detect the sun.
If enabled, you will see sun and number on the menu screen. Go to step 3.
2A. If not enabled:
-
The final step in programming is to set a date and time.
a. Configuration > Date and Time
Once completed
press back 4x -
The Eclipse is now ready to be mounted into the window.
Note: Do NOT leave USB plugged into sensor when mounted.
Sun Sensor Warranty
Roll-A-Shade® warrants Eclipse to be free from defects in materials and workmanship for 5 years when used properly and operated under normal conditions from the date of purchase. If Eclipse is found to be defective and covered by the warranty, we will, at our option, repair or replace it free of charge. This product warranty does not cover any conditions or damages resulting from misuse or abuse, accidents, alterations, neglect, damage by others, natural disasters, exposure to the elements, or failure to follow Roll-A-Shade’s instructions with respect to installation, use, and maintenance. The repair or replacement of the defective product is the purchaser’s sole remedy and the limit of Roll-A-Shade’s obligation. EXCEPT AS EXPRESSLY PROVIDED IN THIS PARAGRAPH, ROLL-A-SHADE® MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND, NATURE, OR DESCRIPTION, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS OF ANY PRODUCTS FOR ANY PARTICULAR PURPOSE, AND HEREBY DISCLAIMS THE SAME. In no event shall Roll-A-Shade® be liable or responsible for incidental or consequential damages or for any other direct or indirect damage, loss, cost, expense, or fee. WARRANTY Exclusions:
- Installation and usage are not in accordance with our installation and operating instructions.
- The product has been opened, dismantled, or returned with clear evidence of abuse or other damage.
- The product has been used to perform functions other than the functions it was designed to handle, namely motorizing window shades
- The product is used with electrical accessories (switches, relays, etc.) that have not been previously approved in writing by the Roll-A-Shade®
Roll-A-Shade Eclipse
FCC ID: 2AUXUECLIPSE-S1
Contains FCC ID: QOQMGM12P3
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
(OPTIONAL) Sun Sensor Orientation
(A) Click the right button to access “Main Menu”. (B) Use navigation buttons
to access “Configuration”. (C) Navigate to “Display”. (D) Click “Orientation”.
(E) You will see four different options of display orientations.
Note: Selection orientation in the display settings to adjust to the
following direction: top, bottom, and/or side installation, etc.
|
---|---
| 
www.rollashade.com
© Copyright 2021 Roll-A-Shade Inc., All rights reserved. – Contractor #916075
ECLIPSE Ver: 1103
Rev: 04.19.2021 Page 6 of 6
12101 Madera Way
Riverside, CA 92503
Phone: 888-245-5077
Fax: 951-245-5075
www.rollashade.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>