ROLL-A-SHADE RASZ150VER.3 Blackout Cordless Roller Shade Instruction Manual

ROLL-A-SHADE RASZ150VER.3 Blackout Cordless Roller Shade

Specifications

• Product Name: ZIPSHADE 150 OVER 118 WIDE
• Mounting: Inside Mount Application
• Hardware Included: 3 mm Allen screw, 25 Torque Screw, 1.5 Self-tapping screws, 25 Torque Bit, Level, 3/16 Drill Bit, 3 mm Allen Wrench

Product Usage Instructions

Disassembling Side Channels:
Remove 3 mm Allen screws from the front of the side channel. Take off the front cover and inner rail. Keep track of all screws.

Drilling Holes:
Drill out holes using a 3/16 drill bit. If inside mount, drill out holes on the side of the side channel.

Disassembling Headbox:
Remove all components inside the headbox.

Lifting Box into Opening:

1. Insert both side channels A and B into headbox locking pins.
2. Lift headbox into the opening with two workers.
3. Secure both side channels A and B through top hole.
4. Ensure channels are plumb and width is exact for proper operation.

Securing the Headbox
Secure the headbox close to the groove with screws in the center and on the sides. Ensure it is leveled.

Securing the Side Channels:
Ensure channels are plumb and width is exact. Verify width at top and bottom before securing with screws.

Re-installing the Shade

1. Feed motor cord through grommet.
2. Insert shade into pin end bracket and secure motor bracket.
3. Re-attach plug and insert front part of headbox.

Inserting the Zipper into the Inner Rail:
Follow specific instructions for each side channel’s inner rail orientation while inserting the zipper.

Frequently Asked Questions (FAQ):

• Q: Do I need special tools to install ZIPSHADE 150 OVER 118 WIDE?
  A: Yes, you will need tools like a 3 mm Allen wrench, Torque Screw, Self- tapping screws, Level, and Drill Bit for installation.

• Q: How do I ensure proper operation of the shade?
  A: Make sure to follow the exact width requirements for mounting and securing both headbox and side channels, as well as leveling them properly.

ZIPSHADE 150 OVER 118″ WIDE
INSTALLATION INSTRUCTIONS
Rollashade.com
info@rollashade.com
951.245.5077
© Copyright Roll-A-Shade® Inc. All Rights Reserved.

ZIPSHADE 150 OVER 118″ WIDE | INSIDE MOUNT APPLICATION

1 DISASSEMBLE 3-PART SIDE CHANNELS
Remove 3 mm Allen screws from front of side channel. Once all screws are removed, take off front cover and remove the inner rail. DO NOT LOSE SCREWS!

2 DRILL OUT HOLES
Side channels are pre-punched for holes. When drilling out holes use 3/16” drill bit. If shade is inside mount, drill out holes on the side of the side channel.

DISASSEMBLE HEADBOX
Remove all components inside headbox.

LIFTING BOX INTO OPENING

• From working position, insert both side channel A and Channel B into headbox locking pins. Using both
  workers, grab each side channel and lift headbox into opening.

• Once headbox and side channels are resting in opening, secure both A and B side channels through top hole.

• Using a level, make sure Side Channel A is plumb. Insert screw in bottom hole. Using a level, make sure Side Channel B is plumb. Prior to securing, double check width at the top and bottom of the side channel. When width is verified and Side Channel B is plumb, insert screw in bottom hole. WIDTH MUST BE EXACT FOR SHADE TO OPERATE PROPERLY.

• Continue affixing channels through remaining holes.

SECURING THE HEADBOX | WHEN SHADES ARE OVER 118” WIDE, THE HEADBOX MUST BE SECURED
Always secure the headbox as close as possible to the groove. One screw needs to be secured in the center of the headbox. At least two additional screws need to be secured on the left and right of the box, as close as possible to the side brackets.

The PVC-side channel extends from the aluminium side channel. If you shorten the aluminium side channel, you need to take into account the same overlength for the PVC side channel.

SECURING THE SIDE CHANNELS
Using a level, make sure Side Channel A is plumb. Insert screw in bottom hole. Using a level, make sure Side Channel B is plumb. Prior to securing, double check width at the top and bottom of the side channel. When width is verified and Side Channel B is level, insert screw in bottom hole. WIDTH MUST BE EXACT FOR SHADE TO OPERATE PROPERLY. Once width is verified at top and bottom, insert remaining screws to secure side channels.

RE-INSTALLING THE SHADE

• Feed motor cord through grommet.
• Place pin end inside the pin end bracket and insert the shade. Once shade is inserted, secure the motor bracket by installing the two Phillips screws back into the bracket.
• Make sure cord is fed through grommet and re-attach plug.
• Re-insert front part of headbox into the groove and secure by screwing in two screws on the underside of the box.

INSERTING THE ZIPPER INTO THE INNER RAIL

• A INNER RAILS ARE SPECIFIC TO EACH SIDE CHANNEL. The top of the inner rail has a “V” shape cut into it. The bottom of the inner rail has a notch. The notch should face the installer when installing – the notch will determine whether the rail belongs in the right or left left side channel.
• B Slide zipper into the inner rail from bottom to top. To secure the inner rail inside the side channel, hook the foam guides behid the lip in the side channel. At the bottom of the inner rail, hook the notch behind the clip. This will lock the inner rail into position.

ENCLOSING THE SIDE CHANNELS
Insert the front part of the channel into the installed channel. Insert screws back into side channel to secure.

PROGRAMMING REMOTES
Please see corresponding programming instructions.
RASZ150VER.3 6 OF 18 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.

ZIPSHADE 150 OVER 118″ WIDE | OUTSIDE MOUNT APPLICATION

DISASSEMBLE 3-PART SIDE CHANNELS
Remove 3 mm Allen screws from front of side channel. Once all screws are removed, take off front cover and remove the inner rail. DO NOT LOSE SCREWS!

DRILL OUT HOLES
Side channels are pre-punched for holes. When drilling out holes use 3/16” drill bit. If shade is outside mount, drill out holes on the back of the channel.

MAKE YOUR MARKS
Using the back piece of one side channel (side channel A), make sure side channel is plumb for installation. Using a pencil, mark the holes.

DISASSEMBLE HEADBOX
Remove all components inside headbox.

MOUNTING SIDE CHANNEL A
Line up holes with your marks. Using a torque 25 screw, drill screw through the top hole of the side channel.

SECURING THE HEADBOX AND MOUNTING SIDE CHANNEL B
Using both workers, lift headbox into position. Slide box into the back part of the side channel A ensuring that the locking pins are inserted into the side channel. Place level on headbox, ensuring it is level. Insert Side Channel B into the locking pins on headbox. One headbox is level, screw torque screw into the top hole in Side Channel B. The box should now be locked into both side channels.

SECURING THE HEADBOX | WHEN SHADES ARE OVER 118” WIDE, THE HEADBOX MUST BE SECURED
Always secure the headbox as close as possible to the groove. One screw needs to be secured in the center of the headbox. At least two additional screws need to be secured on the left and right of the box, as close as possible to the side brackets.

The PVC-side channel extends from the aluminium side channel. If you shorten the aluminium side channel, you need to take into account the same overlength for the PVC side channel.

SECURING THE SIDE CHANNELS
Using a level, make sure Side Channel A is plumb. Insert screw in bottom hole. Using a level, make sure Side Channel B is plumb. Prior to securing, double check width at the top and bottom of the side channel. When width is verified and Side Channel B is level, insert screw in bottom hole. WIDTH MUST BE EXACT FOR SHADE TO OPERATE PROPERLY. Once width is verified at top and bottom, insert remaining screws to secure side channels.

RE-INSTALLING THE SHADE

• A Feed motor cord through grommet.
• B Place pin end inside the pin end bracket and insert the shade. Once shade is inserted, secure the motor bracket by installing the two Phillips screws back into the bracket.
• C Make sure cord is fed through grommet and re-attach plug.
• D Re-insert front part of headbox into the groove and secure by screwing in two screws on the underside of the box.

INSERTING THE ZIPPER INTO THE INNER RAIL

• A INNER RAILS ARE SPECIFIC TO EACH SIDE CHANNEL. The top of the inner rail has a “V” shape cut into it. The bottom of the inner rail has a notch. The notch should face the installer when installing – the notch will determine whether the rail belongs in the right or left left side channel.
• B Slide zipper into the inner rail from bottom to top. To secure the inner rail inside the side channel, hook the foam guides behid the lip in the side channel. At the bottom of the inner rail, hook the notch behind the clip. This will lock the inner rail into position.

ENCLOSING THE SIDE CHANNELS
Insert the front part of the channel into the installed channel. Insert screws back into side channel to secure.

PROGRAMMING REMOTES
Please see corresponding programming instructions.
RASZ150VER.3 11 OF 18 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.

ZIPSHADE 150 UNDER 10FT WIDE
INSTALLATION INSTRUCTIONS
Rollashade.com
info@rollashade.com
951.245.5077
© Copyright Roll-A-Shade® Inc. All Rights Reserved.

ZIPSHADE 150 UNDER 10 FEET WIDE | INSIDE MOUNT APPLICATION

DISASSEMBLE 3-PART SIDE CHANNELS
Remove 3 mm Allen screws from front of side channel. Once all screws are removed, take off front cover and remove the inner rail. DO NOT LOSE SCREWS!

DRILL OUT HOLES
Side channels are pre-punched for holes. When drilling out holes use 3/16” drill bit. If shade is inside mount, drill out holes on the side of the side channel.

LIFTING BOX INTO OPENING

• A From working position, insert both side channel A and Channel B into headbox locking pins. Using both workers, grab each side channel and lift headbox into opening.
• B Once headbox and side channels are resting in opening, secure both A and B side channels through top hole.
• C Using a level, make sure Side Channel A is plumb. Insert screw in bottom hole. Using a level, make sure Side Channel B is plumb. Prior to securing, double check width at the top and bottom of the side channel. When width is verified and Side Channel B is plumb, insert screw in bottom hole. WIDTH MUST BE EXACT FOR SHADE TO OPERATE PROPERLY.
• D Continue affixing channels through remaining holes.

The PVC-side channel extends from the aluminium side channel. If you shorten the aluminium side channel, you need to take into account the same overlength for the PVC side channel.

INSERTING THE ZIPPER INTO THE INNER RAIL

• A INNER RAILS ARE SPECIFIC TO EACH SIDE CHANNEL. The top of the inner rail has a “V” shape cut into it. The bottom of the inner rail has a notch. The notch should face the installer when installing – the notch will determine whether the rail belongs in the right or left left side channel.
• B Slide zipper into the inner rail from bottom to top. To secure the inner rail inside the side channel, hook the foam guides behid the lip in the side channel. At the bottom of the inner rail, hook the notch behind the clip. This will lock the inner rail into position.

ENCLOSING THE SIDE CHANNELS
Insert the front part of the channel into the installed channel. Insert screws back into side channel to secure.

PROGRAMMING REMOTES
Please see corresponding programming instructions.

ZIPSHADE 150 UNDER 10 FEET WIDE | OUTSIDE MOUNT APPLICATION

DISASSEMBLE 3-PART SIDE CHANNELS
Remove 3 mm Allen screws from front of side channel. Once all screws are removed, take off front cover and remove the inner rail. DO NOT LOSE SCREWS!

DRILL OUT HOLES
Side channels are pre-punched for holes. When drilling out holes use 3/16” drill bit. If shade is outside mount, drill out holes on the back of the channel.

MAKE YOUR MARKS
Using the back piece of one side channel (side channel A), make sure side channel is plumb for installation. Using a pencil, mark the holes.

MOUNTING SIDE CHANNEL A
Line up holes with your marks. Using a torque 25 screw, drill screw through the top hole of the side channel.

SECURING THE HEADBOX AND MOUNTING SIDE CHANNEL B
Using both workers, lift headbox into position. Slide box into the back part of the side channel A ensuring that the locking pins are inserted into the side channel. Place level on headbox, ensuring it is level. Insert Side Channel B into the locking pins on headbox. One headbox is level, screw torque screw into the top hole in Side Channel B. The box should now be locked into both side channels.

The PVC-side channel extends from the aluminium side channel. If you shorten the aluminium side channel, you need to take into account the same overlength for the PVC side channel.

INSERTING THE ZIPPER INTO THE INNER RAIL

• A INNER RAILS ARE SPECIFIC TO EACH SIDE CHANNEL. The top of the inner rail has a “V” shape cut into it. The bottom of the inner rail has a notch. The notch should face the installer when installing – the notch will determine whether the rail belongs in the right or left left side channel.
• B Slide zipper into the inner rail from bottom to top. To secure the inner rail inside the side channel, hook the foam guides behid the lip in the side channel. At the bottom of the inner rail, hook the notch behind the clip. This will lock the inner rail into position.

ENCLOSING THE SIDE CHANNELS
Insert the front part of the channel into the installed channel. Insert screws back into side channel to secure.

PROGRAMMING REMOTES
Please see corresponding programming instructions.

RASZ150VER.3 18 OF 18 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.

References

• Roll-A-Shade - Commercial Window Shade Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>