Plus Shade Open Roll Coupled

“`html

Product Specifications

• Product Name: PLUS+ SHADE OPEN ROLL
  COUPLED

• Contact: Rollashade.com | info@rollashade.com
  | 951.245.5077

• Hardware Included: Brackets, Link Bracket,
  Adjuster & Locking Clip, Bracket Wall Switch Switch Covers,
  Box, #14 Screw, Screws, Zip Ties, Wire Tie Pads, Adjuster
  Wrench

• Tools Supplied: 3/8 Hex Head Phillips Head,
  1/8 Drill Bit

• Tools Required: Drill

Product Usage Instructions

1. Installation

Inside or Outside Application: Note that all
shades may be pre-programmed to sensors, remotes, and/or wall
switches upon arrival.

Mounting Location: Place brackets in their
mounting location, mark screw holes, pre-drill using a 1/8 drill
bit, and install the brackets with the provided screws.

Alignment: Check to ensure brackets are level
and aligned.

2. Motor End Installation

Line up the motor with the motor bracket and push the motor into
place.

3. Additional Linked Shades Installation

For linked shades, slide bearing onto the end of the link pin
with holes facing away from the motor. Ensure holes are vertical
and slide onto the bracket. Insert locking clip into bearing until
it clicks.

4. Shade Pin End Installation

Depress pin end and slide onto bracket until pin engages in the
center hole. Press idler shaft all the way to the bracket.

5. Adjusting Coupler

Use the wheel on the infinite adjuster to adjust the level of
the bottom of the slave shade(s) until it becomes level with the
motor shade.

6. Plug in Motor

Plug in the motor according to your city/state code
requirements.

7. Shade Adjusting and Limits

If necessary, adjust the shade to ensure it hangs straight. For
adjusting limits, refer to the programming instructions based on
the motor used for your application.

Frequently Asked Questions (FAQ)

Q: Can I use these shades for both inside and outside

applications?

A: Yes, the shades can be installed for both inside and outside
applications as per the provided instructions.

Q: Is it possible to program the shades to work with sensors

and remotes?

A: Yes, all shades may be pre-programmed to sensors, remotes,
and/or wall switches upon arrival as mentioned in the
instructions.

“`

PLUS+ SHADE OPEN ROLL COUPLED
INSTALL ATION INSTRUCTIONS
Rollashade.com info@rollashade.com 951.245.5077
© Copyright Roll-A-Shade® Inc. All Rights Reserved.

HARDWARE INCLUDED

TOOLS SUPPLIED

TOOLS REQUIRED

Shades + Motors
Shade 1 Shade 2 Shade 3
STOP

Brackets

Link Bracket

Adjuster & Locking
Clip

Bracket Wall Switch Switch

Covers

Box

14 Screw

Screws

Zip Ties

Wire Tie Pads

Adjuster Wrench

3/8″ Hex Head Phillips Head 1/8″ Drill Bit
Drill

1 INSIDE OR OUTSIDE APPLICATION NOTE: ALL SHADES MAY BE PRE-PROGRAMMED TO SENSORS, REMOTES, AND/OR WALL SWITCHES UPON ARRIVAL
OUTSIDE
INSIDE

INSIDE

OUTSIDE

RASPSORCMVER.3 2 OF 6 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.

2 MOUNTING LOCATION

Place your first bracket in its mounting location and mark the screw holes. Place your brackets in its mounting location and repeat the process.

A IDLE BRACKET

B IDLE BRACKET

C SUPPORT BRACKET

D MOTOR BRACKET

3 SCREW INSTALLATION
Next, pre-drill your screw holes using a 1/8″ drill bit. Install the brackets with the provided screws using the 1/4″ hex head driver.

RASPSORCMVER.3 3 OF 6 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.

4 ALIGNMENT Check to make sure your brackets are level and aligned.

5 MOTOR END INSTALLATION

Lineup to motor bracket. Push motor into motor bracket.

A

B

6 ADDITIONAL LINKED SHADES INSTALLATION

Go to link end of motor shade, and with holes facing away from the motor, slide bearing onto end of link pin (rotating slightly if needed (B)). Make sure holes are vertical as picture C shows and slide onto bracket. Once firmly into bracket, rotate holes 90 degrees so holes are as picture. Repeat process with additional shades.

A

B

VIDEO

• TURN ADJUSTER 90°

C

D

• ADJUSTER TURNED RASPSORCMVER.3 4 OF 6 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.

E

F

*INSERT LOCKING CLIP INTO BEARING UNTIL IT CLICKS.

NOTE: Bearing clip cannot not be removed once engaged.

G

H

7 SHADE PIN END INSTALLATION

Depress pin end and slide onto bracket until pin engages in center hole. Press idler shaft all the way to the bracket.

A

B

C

D

ALIGN TANG SHAFT COUPLER WITH SHAFT.

INSERT INTO SUPPORT BRACKET.

RASPSORCMVER.3 5 OF 6 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.

9 ADJUSTING COUPLER
NOTE: Once link shade secured, use wheel on infinite adjuster to adjust the level of the bottom of shade of slave shade(s) until it becomes level with Motor shade. The leveling can be performed in both Up and Down direction. A spanner is available if space is too tight to get fingers around the adjusting wheel.

A

B

8 PLUG IN MOTOR
· Run motor power cord to nearest power outlet. · Install wire tie pads and secure with zip ties to hold wire down. · The path of the wire should be parallel with mullions and/or drop ceiling tiles
ensuring the cable is neatly organized. · Any modifications to the power cable should be done by a certified electrician to
meet your city/state code requirements.
10 SHADE ADJUSTING (IF NECESSARY)
· Roll shade up and down to confirm hembar is level and material rolls up straight on center tube. · If the hembar is not level, lower shade until you see the metal tube. · Add layers of masking tape to the metal tube to the end that is too low until hembar is straight. · If the material tracks to one side, lower shade until you see the metal tube. · Add layers of masking tape to the metal tube to the end that is opposite the direction of tracking, until shade rolls
up straight.

11 ADJUSTING LIMITS (IF NECESSARY) See programming instructions based on the motor used for your application.
RASPSORCMVER.3 6 OF 6 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.

References

• Roll-A-Shade - Commercial Window Shade Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>