ROLL-A-SHADE RASOCSMTREVER.1 Signature Motorized Eclipse Shades Instruction Manual

: June 16, 2024
: ROLL-A-SHADE

Table of Contents

ROLL-A-SHADE RASOCSMTREVER.1 Signature Motorized Eclipse Shades
Specifications
Cleaning the Shade Material
FAQ
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ROLL-A-SHADE RASOCSMTREVER.1 Signature Motorized Eclipse Shades

ROLL-A-SHADE RASOCSMTREVER-1-Signature-Motorized-Eclipse-Shades-
PRODUCT

Specifications

Product Name : RAS – Shade Operation and Cleaning Signature Motorized + Eclipse
Automation: Automated with sun sensors
Acclimation Time: Up to 48 hours after installation to automate correctly
Control: Four horizontal buttons near the center of the switch
Channels: Four selectable channels
Commands: Shade up, stop, shade down, 25% open, 50% open, 75% open

Lowering and Raising the Shade
First, select a channel to operate; press one of the four horizontal buttons near the center of the switch (can select multiple channels at once). The channel will light green when engaged (press again to disengage). Next, select the command; shade up (top right), stop (middle right), or shade down (bottom right). Other commands are 25% open (top left), 50% open (middle left) or 75% open (bottom left).

ROLL-A-SHADE RASOCSMTREVER-1-Signature-Motorized-Eclipse-Shades-
FIG-1

Warnings

Limits are set on the shades causing them to raise or lower to a comfortable length. Do not try to raise or lower the shades past this as it may damage the shade or remote.
Pulling the bottom of the shade may damage the motor, brackets or shade, which can cause the shade to become inoperable.

Recommended Cleaning Methods

Cleaning the Shade Material

Dusting: Regular dusting maintains a like-new appearance of shades.
Vacuuming: For deeper cleaning, vacuum gently with a brush attachment.
The best method of cleaning is by regular washing of the fabric using a solution of warm water and mild detergent. Removing window shades may void the manufacturer’s warranty and or damage the motors.
It is recommended that cleaning occurs at a time of day that allows the shades to dry while in the “down” position (overnight).

Cleaning the Shade Material

Avoid temperature extremes. Heat accelerates chemical reactions and may evaporate water from the solution. Extremely low temperatures may give poor cleaning effects. Cleaning under adverse conditions may result in streaking or staining. Ideally, cleaning should be done at a moderate temperature and out of direct sunlight.
All surfaces should be cleaned using a soft cloth or sponge.
To prevent marring, make sure cleaning sponges, cloth, etc, are grit-free.
Over-cleaning or excessive rubbing can do more harm than good.
Strong solvents or strong cleaner concentrations can cause damage to painted surfaces.
Avoid abrasive cleaners. Do not use household cleaners that contain abrasives on painted surfaces.
Abrasive materials such as steel wool, abrasive brushes, etc, can harm finishes.
Never use paint removers, aggressive alkaline, acid, or abrasive cleaners. Always do a test surface.
Follow the manufacturer’s recommendations for mixing and diluting any recommended cleaners. When using recommended solutions avoid drips and splashes. Remove run-downs as quickly as possible.

FAQ

Frequently Asked Questions (FAQ)

Q: How long does it take for the shades to acclimate to automation after installation?
- A: The shades may take up to 48 hours to acclimate to being automated after installation.
Q: What happens if I override the automation with the controls?
- A: If you override the automation with the controls, it will reset the automation and will again take up to 48 hours to get back to automating correctly.
Q: How do I select a channel to operate?
- A: Press one of the four horizontal buttons near the center of the switch to select a channel. The selected channel will light green when engaged.
Q: How do I clean the shade material?
- A: To clean the shade material, remove any dust or debris using a soft brush or vacuum cleaner with a brush attachment. Then, dampen a clean, non-abrasive cloth or sponge in a mild cleaning solution of warm water and mild detergent. Gently wipe the shade material, avoiding scrubbing or applying excessive pressure. Rinse with clean water and allow the shade material to air dry completely before operating the shade again.