ICI PTZ 640 DetectIr IR Camera User Guide
- September 9, 2024
- ICI
Table of Contents
PTZ 640 DetectIr IR Camera
“`html
Product Information
Specifications
- Model: DetectIR PTZ 640
- Manufacturer: ICI
- Location: Beaumont, TX, USA
- Revision: 07.2024-001
Product Usage Instructions
Package Includes
The package includes the following items:
- DetectIR PTZ 640 device
- Ethernet Cable
- Waterproofing Kit
- Software USB Drive
Ensure all items are present before continuing with the
installation.
Tools
For personal installs, all tools and equipment required for
installation are provided by the company. Professional installation
is recommended due to the weight of the PTZ device. Ensure the PTZ
functions normally before proceeding with the installation.
PPE Requirements
Comply with site safety and PPE requirements. Safety glasses
must be worn at all times, and gloves are highly recommended during
installation.
Set Up
-
Drill four mounting holes on the surface as per the
diagram. -
Affix the PTZ device to the bracket using the mounting
screws. -
Wire the PTZ device according to the pigtail cable diagram
provided:- P1 Power AC 24V
- P2 Ground
- P3 Network (LAN)
- P4 RS-485
- P5 Video (BNC)
- P6 Alarm out (ALARM OUT)
- P7 Alarm in (ALARM IN)
- P8 Audio out (AUDIO OUT)
- P9 Audio in (AUDIO IN)
-
Connect the camera with an alarm signal input and switch
output. An external power supply is required for connecting the
alarm apparatus.
FAQ
Q: Can I install the DetectIR PTZ 640 by myself?
A: While personal installs are possible, professional
installation is recommended due to the weight and technical
requirements of the PTZ device.
Q: What should I do if any components are missing from the
package?
A: Ensure all components are present before starting the
installation. If anything is missing, contact customer support
immediately.
Q: Is it necessary to wear gloves during installation?
A: Gloves are highly recommended to ensure safety during
installation. Make sure to comply with all site safety and PPE
requirements.
“`
Guide
Industry
DETECTIR PTZ 640
QUICK START GUIDE
ICI cameras fall under US Federal Law and Export Control.
2105 W. Cardinal Dr. Beaumont, TX 77705 Phone:
409-861-0788 Toll Free:
866-861-0788 infraredcameras.com
support@infraredcameras.com We Are IR TM
©Copyright 2024, Infrared Cameras, Inc. – All rights reserved. The contents of
this document may not be reproduced in whole or in parts without the written
consent of the copyright owner.
Printed in the United States of America.
2105 W. Cardinal Dr. Beaumont, TX 77705
866-861-0788 www.infraredcameras.com
Revision: 07.2024-001
THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE SPECIFICATIONS OF THE PRODUCT
WITHOUT PRIOR NOTIFICATION. THE MANUFACTURER ALLOWS HIMSELF THE RIGHT TO
MODIFY WITHOUT ANY PRELIMINARY OPINION THE TECHNICAL SPECIFICATIONS OF THE
PRODUCT. THIS MANUAL MAY CONTAIN TECHNICAL INACCURACIES OR TYPOGRAPHICAL
ERRORS.
NOTICE ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE
BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE ARE
PROVIDED “AS IS” WITH ALL FAULTS. ICI DISCLAIMS ALL WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR
A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING,
USAGE, OR TRADE PRACTICE.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET
FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE
INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE
SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR ICI REPRESENTATIVE FOR A
COPY.
IN NO EVENT SHALL ICI BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR
INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR
DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF
ICI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
2
Package Includes
DetectIR PTZ 640 device
Ethernet Cable
Waterproofing Kit
Software USB Drive
ENSURE ALL SYSTEM EQUIPMENT AND COMPONENT ITEMS ARE
PRESENT BEFORE CONTINUING.
3
Tools
· Electric drill · Expansion bolts · Securing cables or straps
ON PERSONAL INSTALLS, THE COMPANY PROVIDES ALL THE TOOLS AND EQUIPMENT
REQUIRED TO SUCCESSFULLY COMPLETE THE INSTALLATION.
PROFESSIONAL INSTALLATION IS RECOMMENDED.
THE PTZ IS HEAVY, SO YOU MUST CHECK WHETHER THE PTZ CAN BE POWERED ON AND THE
SELF-CHECK AND PTZ CONTROL IS NORMAL OR NOT. START INSTALLING AFTER ALL THE
TESTS ARE NORMAL.
MOUNTING GUIDES VARY BY BRACKET. DO NOT DRILL HOLES BEFORE RECEIVING THE
PACKAGE.
PPE Requirements
· Safety glasses · Working gloves (recommended) · Comply with all site PPE
requirements
ENSURE THE INSTALLATION COMPLIES WITH SITE SAFETY AND PPE REQUIREMENTS. SAFETY
GLASSES SHOULD BE WORN AT ALL TIMES. GLOVES ARE HIGHLY RECOMMENDED.
4
Set Up A.
Drill four mounting holes on the mounting surface according to the diagram.
B.
Affix the PTZ device to the bracket using the mounting screws.
5
C.
Wire the PTZ device according to the pigtail cable diagram.
P1 Power AC 24V
P1
P2 Ground P2
P3 Network (LAN)
P4 RS-485
P3
P5 Video (BNC) P4
P6 Alarm out (ALARM OUT)
P5
P7 Alarm in (ALARM IN)
P8 Audio out (AUDIO OUT)
P6
P9 Audio in (AUDIO IN)
P7
P8 P9
PIGTAIL CABLES VARY BASED ON THE PRODUCT MODEL.
6
D.
The camera can be connected with an alarm signal (0 ~ DC5V) input and switch
output (no voltage).
AN EXTERNAL POWER SUPPLY IS REQUIRED WHEN CONNECTING THE ALARM APPARATUS.
E.
Use the waterproof tape to tightly wrap the wiring terminal and nearby cables.
Continue
wrapping until the wiring terminal and surrounding cables are fully covered
with
the waterproof tape.
7
F.
Thread the network cable through the fastening nut and then through the main
body of
the waterproof cover.
G.
Break the waterproof rubber ring and place it on the network cable between the
main body of the waterproof cover
and the fastening nut.
H.
Insert the O-shaped rubber ring into the network port, then insert the
network cable into the network port.
8
I.
Align the notch of the network port with the buckle of the main body of the
waterproof cover, put the main body of the waterproof cover into the end of
the network port, and tighten it clockwise.
J.
Insert the waterproof rubber ring into the main body of the waterproof cover;
then,
turn the fastening nut clockwise and press the waterproof rubber ring tightly.
K.
After installation, apply anti-corrosion paint to all fixed screws and nuts
until it overflows, ensuring that the screw heads
are completely covered.
9
Software
Software arrives installed on computers and tablets purchased from ICI as
complete systems and it will launch automatically on startup. A copy of the
software is provided on the Software USB Drive. Documentation can be found
online on the IR Flash Pro web page under the Downloads section or at this
address:
https://infraredcameras.com/ir-flash-pro-manual/
Recommended System Requirements
· Processor: i5 Quad Core or above · RAM: 4 GB or above · OS: Windows 8/8.1/10
· Hard Drive: 256 GB or above · Resolution: 1920 x 1080
Use the following steps if installing IR Flash Pro on a user computer:
A.
B.
Install IR Flash software using the software USB drive. Refer to the IR Flash User Manual for instructions.
Once installed, launch IR Flash software by double-clicking the
associated desktop icon.
10
About ICI / Contact
Infrared Cameras, Inc. 2105 W. Cardinal Dr. Beaumont, TX 77705
Phone: 409-861-0788 | Toll Free:
866-861-0788 | International:
409-861-0788
General Inquiry: support@infraredcameras.com Website: www.infraredcameras.com
You may reach a representative by phone or email Mon Fri 8:00AM – 5:00PM
CST. ICI manufactures complete systems and software. We can provide complete
engineering, software, and OEM solutions. Our Fortune 500 clients rely on us
for infrared equipment and thermography training (which we offer through the
Infrared Training Institute). In addition to providing custom germanium,
silica, and sapphire optics, we also build windows for enclosures, as well as
custom pan and tilt units. We can even provide customizable explosion-proof
systems. Our knowledge and experience stems from years of using infrared
imaging and temperature measurement instruments to provide solutions to:
managers, engineers, scientists, inspectors and operators in space, power
companies, medical, pulp and paper, food industry, research and development,
and various process industries. You can see our products and services used in
industrial, commercial, and government applications worldwide. Originally
named Texas Infrared (still DBA), Infrared Cameras, Inc. has been in business
since March, 1995. Thank you for your dedicated and continued support.
11
References
- Infrared Cameras, Service & Software | ICI Thermal Cameras
- Infrared Cameras, Service & Software | ICI Thermal Cameras
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>