ICI CF-818 Hotspot IR Non-Contact Thermometer User Guide
- June 6, 2024
- ICI
Table of Contents
ICI CF-818 Hotspot IR Non-Contact Thermometer
©Copyright 2021, Infrared Cameras, Inc. – All rights reserved. The contents of
this document may not be reproduced in whole or in parts without the written
consent of the copyright owner.
Printed in the United States of America.
2105 W. Cardinal Dr.
Beaumont, TX 77705
866-861-0788
www.infraredcameras.com
Revision: 3.2021-001
THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE SPECIFICATIONS OF THE PRODUCT
WITHOUT PRIOR NOTIFICATION. THE MANUFACTURER ALLOWS HIMSELF THE RIGHT TO
MODIFY WITHOUT ANY PRELIMINARY OPINION THE TECHNICAL SPECIFICATIONS OF THE
PRODUCT. THIS MANUAL MAY CONTAIN TECHNICAL INACCURACIES OR TYPOGRAPHICAL
ERRORS.
NOTICE ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE ARE PROVIDED “AS IS” WITH ALL FAULTS. ICI DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR ICI REPRESENTATIVE FOR A COPY.
IN NO EVENT SHALL ICI BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF ICI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Package Includes
ENSURE ALL SYSTEM EQUIPMENT AND COMPONENT ITEMS ARE PRESENT BEFORE BEGINNING SCREENING
Set Up
SELECT AN APPROPRIATE AREA FREE OF IMMEDIATE AIRFLOW FROM DOORWAYS AND AIR CONDITIONING/VENTILATION SYSTEMS. THE SELECTED AREA SHOULD HAVE A STABLE AMBIENT TEMPERATURE BETWEEN 20 °C AND 24 °C AND RELATIVE HUMIDITY RANGE FROM 10% TO 50%.
-
Remove screen protector from HotSpot IR thermometer.
-
Press down and forward on the battery bay door to open.
-
Insert AA Batteries into HotSpot IR battery bay.
-
Close battery bay door.
-
Secure battery bay with screw.
-
Power on device by pulling trigger. Device will auto shut-off when not in use.
IF
THE DEVICE IS NOT USED FOR A LONG TIME, THE DEVICE WILL DELAY TURNING ON A FEW
SECONDS IN ORDER TO FIRST TEST THE ROOM TEMPERATURE. -
Aim toward a person’s inner canthus keeping 5 to 15 cm (2” to 5.9”) distance between the thermometer and the person, press the measuring key, and the temperature will display immediately (see the Figure 1 below for the positioning).
-
When the room temperature is significant difference, or there is perspiration on the forehead, you can take the temperature behind the ear lobe (see the Figure 2 below for the positioning).
CRITICAL INFORMATION
- The technology should be used to measure only one subject’s temperature at a time.
- Measurements should not be solely, or primarily, relied upon to diagnose or exclude a diagnosis of any disease.
- Elevated body temperature should be confirmed with secondary evaluation methods (e.g., an NCIT or clinical grade contact thermometer).
- Signage should instruct for the removal of glasses, headwear, and masks.
- Read the current government guidance regarding the use of telethermographic systems for skin temperature measurements. Additional information can be found by reading IEC 80601-2-59:2017 Medical electrical equipment — Part 2-59:
- Particular requirements for the basic safety and essential performance of screening thermographs for human febrile temperature screening and ISO/TR 13154:2017 Medical electrical equipment
- Deployment, implementation and operational guidelines for identifying febrile humans using a screening thermograph.
ABOUT ICI/CONTACT
Infrared Cameras, Inc.
2105 W. Cardinal Dr.
Beaumont, TX 77705
Phone: 409-861-0788
Toll Free: 866-861-0788
International: 409-861-0788
General Inquiry:
support@infraredcameras.com
Website: www.infraredcameras.com
You may reach a representative by phone or email.
Hours: Monday – Friday 8:00AM – 5:00PM CST.
ICI manufactures complete systems and software. We can provide complete
engineering, software, and OEM solutions. Our Fortune 500 clients rely on us
for infrared equipment and thermography training (which we offer through the
Infrared Training Institute).
In addition to providing custom germanium, silica, and sapphire optics, we
also build windows for enclosures, as well as custom pan and tilt units. We
can even provide customizable explosion-proof systems.
Our knowledge and experience stems from years of using infrared imaging and
temperature measurement instruments to provide solutions to: managers,
engineers, scientists, inspectors and operators in space, power companies,
medical, pulp and paper, food industry, research and development, and various
process industries. You can see our products and services used in industrial,
commercial, and government applications worldwide. Originally named Texas
Infrared (still DBA), Infrared Cameras, Inc. has been in business since March,
1995.
Thank you for your dedicated and continued support.
References
- Infrared Cameras, Service & Software | ICI Thermal Cameras
- Infrared Cameras, Service & Software | ICI Thermal Cameras
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>