ICI TDL 300 Turntable Diode Laser User Guide
- June 6, 2024
- ICI
Table of Contents
ICI TDL 300 Turntable Diode Laser
Package Includes
ENSURE ALL SYSTEM EQUIPMENT AND COMPONENT ITEMS ARE PRESENT BEFORE BEGINNING INSTALLATION
Set-Up
- The camera is used as a handheld device.
- Power on device.
TURN ON THE DEVICE BY PRESSING AND HOLDING THE POWER BUTTON UNTIL YOU FEEL
THE VIBRATION; THEN, RELEASE THE POWER BUTTON.
TO POWER OFF THE DEVICE, FIRST DOUBLE-CLICK THE POWER BUTTON TO ENTER
STANDBY MODE; THEN, PRESS AND HOLD THE POWER BUTTON FOR 3 SECONDS.
Charging Instructions
- Align the metal prongs of the charging cable with the bottom of the device; then, touch the cable to the device. Magnets will hold the charging cable in place.
- Plug the USB end of the charging cable into the bottom of the power adapter.
IF THE CHARGING CABLE DOES NOT ATTACH TO THE DEVICE EASILY THE MAGNETS ARE
NOT ALIGNED PROPERLY. INVERT THE MAGNET ALIGNMENT AND TRY AGAIN.
WHEN THE CHARGING CABLE IS NOT PLACED ON THE MAGNETIC CHARGING SLOT CORRECTING
THE DEVICE WILL NOT CHARGE. THE LIGHT FLASHES RED WHEN THE CABLE IS PLACED
CORRECTLY AND THE DEVICE IS CHARGING. WHEN THE BATTERY IS FULLY CHARGED THE
LIGHT TURNS GREEN. A BATTERY ICON SHOWS THE LEVEL OF CHARGE ON THE SCREEN.
CHARGE THE BATTERY FOR A MINIMUM OF 3 HOURS BEFORE USING THE DEVICE.
- Plug power adapter into a 110/120V electrical outlet.
ENSURE THE IMAGER IS NEAR ROOM TEMPERATURE BEFORE CHARGING THE DEVICE. DO
NOT CHARGE IN EXTREMELY HOT OR COLD AREAS. THE BATTERY CAPACITY MAY BE
DECREASED IF CHARGED IN AN EXTREME TEMPERATURE ENVIRONMENT.
IF YOU DO NOT USE THE IMAGER FOR A LONG PERIOD OF TIME, PUT THE DEVICE IN A
COOL AND DRY ENVIRONMENT. THE BATTERY WILL DISCHARGE OVER TIME; THEREFORE, THE
IMAGER SHOULD BE CHARGED OCCASIONALLY TO PREVENT DAMAGE TO THE BATTERY OR THE
DEVICE.
Laser Sight
- Power on the laser sight by pressing the + button on the side of the laser sight.
- Power off the laser sight by pressing the unlabeled button on the side of the laser sight.
- After powering on the device, use a standard flat head screwdriver (not included) to make adjustments to the adjustment screws on the upper and right sides of the laser sight to keep it in alignment with the aiming laser.
AFTER POWERING ON THE DEVICE, MAKE SURE TO ADJUST THE LASER SIGHT TO MATCH TO THE AIMING LASER. WHEN THE DETECTOR IS NOT IN USE, MAKE SURE THE LASER SIGHT IS ALSO TURNED OFF TO EXTEND THE BATTERY LIFE. TO PREVENT EYE DAMAGE AND PERSONAL INJURY, DO NOT LOOK DIRECTLY INTO THE LASER. DO NOT POINT THE LASER DIRECTLY AT PEOPLE OR ANIMALS OR INDIRECTLY OFF REFLECTIVE SURFACES.
Laser Sight Battery Replacement
MAKE SURE THE DEVICE IS ON A FLAT STABLE SURFACE WHEN REMOVING OR REPLACING THE BATTERY.
- Use a hex key (included) to remove the two battery bay bolts.
- Remove battery from battery bay.
- Place a brand new, unused battery in the battery bay.
- Use a hex key (included) to replace the two battery bay bolts.
DO NOT FORCE THE BATTERY INTO THE BATTERY BAY. IF THE USER FEELS
SIGNIFICANT RESISTANCE REMOVE THE BATTERY AND ENSURE IT IS PROPERLY ALIGNED
BEFORE TRYING TO PLACE THE BATTERY INTO THE BATTERY BAY.
ENSURE THE BATTERY COVER IS PROPERLY CLOSED. IMPROPER CLOSURE OF BATTERY COVER
MAY EXPOSE THE BATTERY AND INTERNAL ELECTRONICS TO ELEMENTAL DAMAGE.
About ICI Contact
- Infrared Cameras, Inc.
- 2105 W. Cardinal Dr.
- Beaumont, TX 77705
- Phone: 409-861-0788 | Toll Free: 866-861-0788 | International: 409-861-0788
- General Inquiry: support@infraredcameras.com Website: www.infraredcameras.com
You may reach a representative by phone or email Mon – Fri 8:00 AM – 5:00 PM CST. ICI manufactures complete systems and software. We can provide complete engineering, software, and OEM solutions. Our Fortune 500 clients rely on us for infrared equipment and thermography training (which we offer through the Infrared Training Institute). In addition to providing custom germanium, silica, and sapphire optics, we also build windows for enclosures, as well as custom pan and tilt units. We can even provide customizable explosion-proof systems. Our knowledge and experience stems from years of using infrared imaging and temperature measurement instruments to provide solutions to managers, engineers, scientists, inspectors, and operators in space, power companies, medical, pulp and paper, food industry, research and development, and various process industries. You can see our products and services used in industrial, commercial, and government applications worldwide. Originally named Texas Infrared (still DBA), Infrared Cameras, Inc. has been in business since March 1995. Thank you for your dedicated and continued support.
References
- Infrared Cameras, Service & Software | ICI Thermal Cameras
- Infrared Cameras, Service & Software | ICI Thermal Cameras
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>