ICI Sound DetectAI Acoustic Image Management and Signal Analysis User Guide

: June 5, 2024
: ICI

Table of Contents

Package Contents
Set Up: Package
Battery Installation
Charging Instructions Battery
Memory
Set Up: Package
Charging Instructions Battery Pack
Memory
Declaimer
About ICI / Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ICI Sound DetectAI Acoustic Image Management and Signal Analysis User Guide

Package Contents

Sound DetectAI device
Battery Charger
Power Adapter
Battery x2\
USB Drive

ENSURE ALL SYSTEM EQUIPMENT AND COMPONENT ITEMS ARE PRESENT BEFORE CONTINUING.

THERE ARE MULTIPLE PACKAGE OPTIONS AVAILABLE. SEE PAGES 12-16 FOR INSTRUCTIONS FOR PACKAGE 2.

Sound DetectAI device
Battery cable
Battery Pack
Power Adapter
Power Cord
USB Drive

Set Up: Package

THE SETUP INSTRUCTIONS ONLY APPLY TO PACKAGE 1 SEEN.

The Sound DetectAI is used as a handheld device.
Power on device

POWER ON THE DEVICE BY PRESSING THE POWER BUTTON.
PRESS THE POWER BUTTON AGAIN TO POWER OFF THE DEVICE.

THE ACOUSTIC IMAGER NEEDS SUFFICIENT WARM-UP TIME FOR THE MOST ACCURATE MEASUREMENTS AND BEST IMAGE QUALITY. THIS TIME CAN OFTEN VARY BY NVIRONMENTAL
CONDITIONS. IT IS BEST TO WAIT A MINIMUM OF 10 MINUTES FOR THE DEVICE TO COMPLETELY WARM-UP.

Battery Installation

THE BATTERY CHARGING INSTRUCTION ONLY APPLY TO PACKAGE 1 SEEN .

MAKE SURE TO HOLD THE CAMERA FIRMLY IN BOTH HANDS WHEN REMOVING OR REPLACING BATTERY OR ATTACHING OR REMOVING THE BATTERY BAY COVER.

Hold the camera firmly in both hands placing a thumb on the grip line.
Press the grip line firmly to create a gap.
Keep pressing the grip line and pull battery bay cover up and away to remove the battery bay cover.
Ensure metal contacts are aligned; then, push battery into battery bay.

DO NOT FORCE THE BATTERY INTO THE BATTERY BAY. IF USER FEELS SIGNIFICANT RESISTANCE REMOVE THE BATTERY AND ENSURE METAL CONTACTS ARE ALIGNED BEFORE TRYING TO PLACE BATTERY INTO THE BATTERY BAY.

MAKE SURE TO HOLD THE CAMERA FIRMLY IN BOTH HANDS WHEN REMOVING OR EPLACING BATTERY OR ATTACHING OR REMOVING THE BATTERY BAY COVER.

To replace a battery held in the battery pull the battery tab.
Pressing the grip line, align the bottom of the battery cover inside the slot of the battery bay; then, press the cover toward the device.
Close gap by releasing the battery bay cover.

ENSURE BATTERY COVER IS PROPERLY ATTACHED. IMPROPER ATTACHMENT OF BATTERY COVER MAY EXPOSE THE BATTERY AND INTERNAL ELECTRONICS TO ELEMENTAL DAMAGE.

Charging Instructions Battery

THE BATTERY CHARGING INSTRUCTIONS ONLY APPLY TO PACKAGE 1 SEEN .

THE BATTERY CANNOT BE CHARGED INSIDE THE DEVICE. REMOVE THE BATTERY IN ORDER TO CHARGE IT.

Plug the power adapter cord into the battery charger
Align the battery, and insert the battery into battery charger
Plug power adapter into a 110/120V electrical outlet.

THE BATTERY CHARGING INSTRUCTIONS ONLY APPLY TO PACKAGE 1 SEEN.

IT TAKES 4-6 HOURS TO CHARGE AN EMPTY BATTERY TO FULL.

WHEN THE STATUS LED OF THE CHARGER IS RED THE BATTERY IS BEING CHARGED. THE CHARGER LED TURNS GREEN WHEN CHARGING IS COMPLETE.

ENSURE THE BATTERY IS NEAR ROOM TEMPERATURE BEFORE CHARGING. DO NOT CHARGE THE BATTERY IN EXTREMELY HOT OR COLD AREAS. THE BATTERY CAPACITY MAY BE DECREASED IF CHARGED IN AN EXTREME TEMPERATURE ENVIRONMENT.

DO NOT STORE THE DEVICE WITH THE BATTERY INSTALLED TO PREVENT DAMAGE TO THE BATTERY OR THE DEVICE. REMOVE THE BATTERY FROM THE DEVICE BEFORE STORING.

IF YOU DO NOT USE THE IMAGER FOR A LONG PERIOD OF TIME, PUT THE DEVICE IN A COOL AND DRY ENVIRONMENT. THE BATTERY WILL DISCHARGE OVER TIME; THEREFORE, THE IMAGER SHOULD BE CHARGED OCCASIONALLY TO PREVENT DAMAGE TO THE BATTERY OR THE DEVICE.

Memory

THE MEMORY INSTRUCTIONS APPLY TO BOTH PACKAGE 1 AND PACKAGE 2; SEE PAGES 3-4 FOR PACKAGES.

Align the USB drive and insert it into the top of the device.

DO NOT FORCE THE USB DRIVE INTO THE SLOT. THE SIDE OF THE CARD WITH CONTACT PINS MUST BE INSERTED FIRST. IF THERE IS RESISTANCE FLIP THE CARD AROUND AND TRY AGAIN. TO EJECT THE MEMORY POWER OFF THE DEVICE; THEN, PULL THE CARD FROM THE MEMORY SLOT.

Set Up: Package

THE SETUP INSTRUCTIONS ONLY APPLY TO PACKAGE 2 SEEN ON.

The Sound DetectAI is used as a handheld device.
Align the battery cable; then, plug the battery cable into the battery pack.

HE ACOUSTIC IMAGER NEEDS SUFFICIENT WARM-UP TIME FOR THE MOST ACCURATE MEASUREMENTS AND BEST IMAGE QUALITY. THIS TIME CAN OFTEN VARY BY NVIRONMENTAL CONDITIONS. IT IS BEST TO WAIT A MINIMUM OF 10 MINUTES FOR THE DEVICE TO COMPLETELY WARM-UP.

Align the red orientation marking on the battery cable to the red marking on the device; then, plug the battery cable into the device until a click is heard.

POWER IS SUPPLIED TO THE DEVICE THE MOMENT IT IS PLUGGED INTO THE BATTERY PACK.

THE SYSTEM STARTS IN APPROXIMATELY 10-15 SECONDS. WAIT UNTIL THE USER INTERFACE LOADS BEFORE ATTEMPTING AN ACOUSTIC INSPECTION.

TO POWER OFF THE DEVICE DISCONNECT THE DEVICE FROM THE BATTERY PACK. TO DISCONNECT THE BATTERY CABLE, HOLD THE BATTERY CABLE BY THE LOCK RING AND PULL. THE LOCK RING WILL SLIDE UNTIL IT RELEASES THE CONNECTION.

THE DEVICE HAS AN INTERNAL BACKUP BATTERY WHICH IS CHARGED BY THE BATTERY PACK WHILE IN USE. IT IS RECOMMENDED THE DEVICE STAY POWERED BY THE BATTERY PACK AT LEAST 45 MINUTES IN ORDER TO FULLY CHARGE THE INTERNAL BACKUP BATTERY.

Charging Instructions Battery Pack

THE BATTERY PACK INSTRUCTIONS ONLY APPLY TO PACKAGE 2

Plug the power cord into the power adapter.
Plug the jack end of the power adapter into the battery pack.
Plug power adapter into a110/120V electrical outlet.

WHEN THE BATTERY PACK IS FULL, LIGHTS ON THE SIDE OF THE DEVICE LIGHT UP.

THE BATTERY PACK INSTRUCTIONS ONLY APPLY TO PACKAGE 2

IT TAKES 4-6 HOURS TO CHARGE AN EMPTY BATTERY PACK TO FULL.

WHEN THE STATUS LED OF THE CHARGER IS RED OR YELLOW THE BATTERY PACK IS BEING CHARGED. WHEN THE STATUS LED OF THE BATTERY PACK IS GREEN THE CHARGE IS COMPLETE. THE STATUS LED IS GREEN WHILE THE CONNECTOR IS CONNECTED TO THE BATTERY AND WHEN THE CONNECTOR IS DISCONNECTED.

ENSURE THE BATTERY PACK IS NEAR ROOM TEMPERATURE BEFORE CHARGING. DO NOT CHARGE THE BATTERY PACK IN EXTREMELY HOT OR COLD AREAS. THE BATTERY PACK CAPACITY MAY BE DECREASED IF CHARGED IN AN EXTREME TEMPERATURE ENVIRONMENT.

DO NOT STORE THE DEVICE WITH THE BATTERY PACK ATTACHED TO PREVENT DAMAGE TO THE BATTERY PACK OR THE DEVICE. DETACH THE BATTERY PACK FROM THE DEVICE BEFORE STORING.

IF YOU DO NOT USE THE BATTERY PACK FOR A LONG PERIOD OF TIME, PUT THE BATTERY PACK IN A COOL AND DRY ENVIRONMENT. THE BATTERY PACK WILL DISCHARGE OVER TIME; THEREFORE, THE BATTERY PACK SHOULD BE CHARGED OCCASIONALLY TO PREVENT DAMAGE TO THE BATTERY PACK.

Memory

THE MEMORY INSTRUCTIONS APPLY TO BOTH PACKAGE 1 AND PACKAGE 2; SEE PAGES 3-4 FOR PACKAGES.

Align the USB drive and insert it into the top of the device.

DO NOT FORCE THE USB DRIVE INTO THE SLOT. THE SIDE OF THE CARD WITH CONTACT PINS MUST BE INSERTED FIRST. IF THERE IS RESISTANCE FLIP THE CARD AROUND AND TRY AGAIN. TO EJECT THE MEMORY POWER OFF THE DEVICE; THEN, PULL THE CARD FROM THE MEMORY SLOT.

Declaimer

THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE SPECIFICATIONS OF THE PRODUCT WITHOUT PRIOR NOTIFICATION. THE MANUFACTURER ALLOWS HIMSELF THE RIGHT TO MODIFY WITHOUT ANY PRELIMINARY OPINION THE TECHNICAL SPECIFICATIONS OF THE PRODUCT. THIS MANUAL MAY CONTAIN TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS.

NOTICE ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE ARE PROVIDED “AS IS” WITH ALL FAULTS. ICI DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR ICI REPRESENTATIVE FOR A COPY.

IN NO EVENT SHALL ICI BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF ICI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

About ICI / Contact

Infrared Cameras, Inc.
2105 W. Cardinal Dr.
Beaumont, TX 77705

Phone: 409-861-0788 |
Toll Free: 866-861-0788 |
International: 409-861-0788

General Inquiry: support@infraredcameras.com
Website: www.infraredcameras.com

You may reach a representative by phone or email Mon – Fri 8:00AM – 5:00PM CST.

ICI manufactures complete systems and software. We can provide complete engineering, software, and OEM solutions. Our Fortune 500 clients rely on us for infrared equipment and thermography training (which we offer through the Infrared Training Institute).

In addition to providing custom germanium, silica, and sapphire optics, we also build windows for enclosures, as well as custom pan and tilt units. We can even provide customizable explosion-proof systems.

and temperature measurement instruments to provide solutions to: managers, engineers, scientists, inspectors and operators in space, power companies, medical, pulp and paper, food industry, research and development, and various process industries. You can see our products and services used in industrial, commercial, and government applications worldwide. Originally named Texas Infrared (still DBA), Infrared Cameras, Inc. has been in business since March, 1995

Thank you for your dedicated and continued support.

Printed in the United States of America.

2105 W. Cardinal Dr.
Beaumont, TX 77705
866-861-0788
www.infraredcameras.com

Revision: 06.2022-002