ICI GAS DETECTIR Series Gas Leak Detection Camera User Guide
- June 6, 2024
- ICI
Table of Contents
GAS DETECTOR Series Gas Leak Detection Camera
User Guide
ICI cameras fall under US Federal Law and Export Control.
2105 W. Cardinal Dr. Beaumont, TX 77705
Phone: 409-861-0788
Toll-Free: 866-861-0788
infraredcameras.com
support@infraredcameras.com
We Are IR ™
©Copyright 2022, Infrared Cameras, Inc. – All rights reserved. The contents of
this document may not be reproduced in whole or in parts without the written
consent of the copyright owner.
Printed in the United States of America.
2105 W. Cardinal Dr.
Beaumont, TX 77705
866-861-0788
www.infraredcameras.com
Revision: 02.2022-001
THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE SPECIFICATIONS OF THE PRODUCT
WITHOUT PRIOR NOTIFICATION. THE MANUFACTURER ALLOWS HIMSELF THE RIGHT TO
MODIFY WITHOUT ANY PRELIMINARY OPINION THE TECHNICAL SPECIFICATIONS OF THE
PRODUCT. THIS MANUAL MAY CONTAIN TECHNICAL INACCURACIES OR TYPOGRAPHICAL
ERRORS.
NOTICE ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE
BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE ARE
PROVIDED “AS IS” WITH ALL FAULTS. ICI DISCLAIMS ALL WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR
A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCTS ARE
SET FORTH IN THE INFORMATION
PACKET THAT SHIPPED WITH THE PRODUCT AND IS INCORPORATED HEREIN BY THIS
REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED
WARRANTY, CONTACT YOUR ICI REPRESENTATIVE FOR A COPY.
IN NO EVENT SHALL ICI BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR
INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR
DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF
ICI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Package Includes
ENSURE ALL SYSTEM EQUIPMENT AND COMPONENT ITEMS ARE PRESENT BEFORE BEGINNING INSTALLATION
Set Up
A. The camera can be used as a handheld device.
or
Mount the fully charged device to a tripod using the ¼”-20 mount located on
the body.
MAKE SURE TRIPODS DO NOT BLOCK THE DIRECT PATH OF THROUGH TRAFFIC TO ENSURE THE EQUIPMENT WILL NOT BE MOVED OR KNOCKED DOWN. USING A DIVIDING BARRIER WILL HELP KEEP TRIPODS SEPARATE FROM THE PATH.
TURN ON THE CAMERA BY PRESSING AND HOLDING THE POWER BUTTON FOR AT LEAST THREE
SECONDS.
THE INTERNAL SOFTWARE MAY TAKE UP TO 5 MINUTES TO LAUNCH. DO NOT POWER OFF THE
DEVICE OR PRESS BUTTONS WHILE SOFTWARE IS LAUNCHING. PRESSING BUTTONS OR
TURNING OFF THE DEVICE MAY CORRUPT THE FILE SYSTEMS.
B.Power on device.
PRESS AND HOLD THE POWER BUTTON FOR MORE THAN 5 SECONDS TO SHUT DOWN THE
CAMERA.
THE THERMAL IMAGER NEEDS SUFFICIENT WARM-UP TIME FOR THE MOST ACCURATE
TEMPERATURE MEASUREMENTS AND BEST IMAGE QUALITY. THIS TIME CAN OFTEN VARY BY
ENVIRONMENTAL CONDITIONS. IT IS BEST TO WAIT A MINIMUM OF 10 MINUTES AFTER THE
SOFTWARE HAS FULLY LAUNCHED BEFORE MEASURING TEMPERATURES.
Battery Installation
SET THE THERMAL DEVICE UPRIGHT ON A LARGE FLAT SURFACE WHEN REMOVING OR REPLACING THE BATTERY.
A. Ensure metal contacts are aligned; then, push the battery into the
battery bay until the battery is fully seated in the battery bay. User should
hear a click sound.
B. Pinch the battery bay buckles simultaneously. Battery will be released
from the battery bay.
C. Pull battery from battery bay.
DO NOT FORCE THE BATTERY INTO THE BATTERY BAY. IF USER FEELS SIGNIFICANT
RESISTANCE REMOVE THE BATTERY AND ENSURE METAL CONTACTS ARE ALIGNED BEFORE
TRYING TO PLACE BATTERY INTO THE BATTERY BAY.
ENSURE BATTERY IS INSERTED PROPERLY. IMPROPER INSERTION OF BATTERY MAY EXPOSE
THE BATTERY AND INTERNAL ELECTRONICS TO ELEMENTAL DAMAGE.
Charging Instructions: Option 1
A. While a battery is inside the device, align the power adapter prongs;
then, plug the power adapter cable into the device.
B. Plug the power adapter cord into the power adapter.
D. Plug power cord into a 110/120V electrical outlet.
CHARGE THE BATTERY FOR A MINIMUM OF 3 HOURS BEFORE USING THE DEVICE.
ICI DOES NOT RECOMMEND CHARGING THE DEVICE WHILE IT IS ON A TRIPOD. LAY DEVICE
FACE DOWN ON A FLAT AND STABLE
DESK OR TABLE WHILE CHARGING.
ENSURE THE IMAGER IS NEAR ROOM TEMPERATURE BEFORE CHARGING THE DEVICE. DO NOT
CHARGE IN EXTREMELY HOT OR
COLD AREAS. THE BATTERY CAPACITY MAY BE DECREASED IF CHARGED IN AN EXTREME
TEMPERATURE ENVIRONMENT.
Charging Instructions: Option 2
REMOVE THE BATTERIES FROM THE DEVICE BEFORE CONTINUING WITH THIS METHOD OF CHARGING.
A. Ensure metal contacts are aligned; then, insert batteries into the
battery charging base.
B. Plug
charger cable into the battery charging base.
C. Plug power cord into a 110/120V electrical outlet.
IF YOU DO NOT USE THE IMAGER FOR A LONG PERIOD OF TIME, PUT THE DEVICE IN A COOL AND DRY ENVIRONMENT. THE BATTERY WILL DISCHARGE OVER TIME; THEREFORE, THE IMAGER SHOULD BE CHARGED OCCASIONALLY TO PREVENT DAMAGE TO THE BATTERY OR THE DEVICE.
Memory Card
SET THE THERMAL DEVICE UPRIGHT ON A LARGE FLAT SURFACE WHEN REMOVING OR REPLACING THE BATTERY.
A. Slide the connector bay latch lock and open the connector bay latch door.
B. Slide the battery bay cover latch.
C. Close the battery bay lock. User should hear a click sound.
DO NOT FORCE SD CARD INTO THE SLOT. THE SIDE OF THE CARD WITH CONTACT PINS MUST BE INSERTED FIRST. IF THERE IS RESISTANCE FLIP THE CARD AROUND AND TRY AGAIN.
About ICI / Contact
Infrared Cameras, Inc.
2105 W. Cardinal Dr.
Beaumont, TX 77705
Phone: 409-861-0788 | Toll Free:
866-861-0788 | International:
409-861-0788
General Inquiry:
support@infraredcameras.com
Website: www.infraredcameras.com
You may reach a representative by phone or email Mon – Fri 8:00AM – 5:00PM
CST.
ICI manufactures complete systems and software. We can provide complete
engineering, software, and OEM solutions. Our Fortune 500 clients rely on us
for infrared equipment and thermography training (which we offer through the
Infrared Training Institute).
In addition to providing custom germanium, silica, and sapphire optics, we
also build windows for enclosures, as well as custom pan and tilt units. We
can even provide customizable explosion-proof systems.
Our knowledge and experience stems from years of using infrared imaging and
temperature measurement instruments to provide solutions to: managers,
engineers, scientists, inspectors and operators in space, power companies,
medical, pulp and paper, food industry, research and development, and various
process industries. You can see our products and services used in industrial,
commercial, and government applications worldwide. Originally named Texas
Infrared (still DBA), Infrared Cameras, Inc. has been in business since March,
1995.
Thank you for your dedicated and continued support.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>