Mgctech CB-T20 Wireless Charger User Manual
- September 7, 2024
- MGCTECH
Table of Contents
Mgctech CB-T20 Wireless Charger
Product Information
Specifications:
- Model: XYZ-2000
- Power: 1200W
- Capacity: 2 liters
- Material: Stainless steel
- Dimensions: 10″ x 12″ x 8″
Product Usage Instructions
-
Initial Setup:
Before using the XYZ-2000, ensure that all parts are clean and dry. Place the appliance on a flat, stable surface near a power outlet. -
Filling the Tank:
Open the lid of the tank and fill it with water up to the maximum level indicated. Do not exceed the maximum capacity to avoid spillage. -
Powering On:
Connect the power cord to a suitable power source and press the power button. The device will start heating the water. -
Selecting Temperature:
Use the temperature control knob to set your desired temperature. Wait for the water to reach the set temperature before use. -
Usage:
Once the water reaches the desired temperature, you can use it for various purposes such as making tea, coffee, or instant noodles.
Frequently Asked Questions
Q: Can I use this product to boil milk?
A: It is not recommended to boil milk directly in the XYZ-2000 as it may lead to spillage and difficulty in cleaning.
Q: How often should I clean the appliance?
A: It is advisable to clean the tank and other parts of the appliance after every use to maintain hygiene and prevent any residue buildup.
Q: Is it safe to leave the appliance unattended while in use?
A: It is not recommended to leave the appliance unattended while in use for safety reasons. Always switch off and unplug when not in use.
Product Introduction
This is a multifunctional desktop magnetic 3 in 1 auto rotation wireless charger, which can wirelessly charge mobile phones, headphones, and watches at the same time by power supply. Bid farewell to wired shackles and start a wireless experience.
Product Usage Guide
- Please connect the product through the Type-C quick charging cable to the QC or PD above power adapter, to ensure that it supports fast wireless charging.
- Built-in stepper motor and touch button to support wireless charger automatic rotation function, to compatible with different sizes of qi-enabled smartphones.
- Press and pop up the Watch charging stand, and place the Apple Watch to start wireless charging with 2.5W output.
- Press and pop up the earphone charging stand, and place the earphone case to start wireless charging with 2.5W output.
- Touch-sensitive design that allows for the automatic rotation of your smartphone with different viewing angles. Please do not rotate it by hand to avoid of damage to the product. Please reconnect the power supply and touch the button to adjust it to the correct position.)
Product Parts Description
- Touch button for rotation
- Charging area for phone
- Charging area for earphones
- Charging area for watch
- Indicator Light
- Type-C input port
Specifications
- Input: DC 5V/3A, 9V/3A
- Phone Output: 5W, 10W, 15W
- Product Standard: Qi
- Earphone Output: 2.5W
- Watch Output: 2.5W
- Charging Distance: ≤10mm
- Charging Efficiency: ≤80%
- Product Dimension: 6666105mm
- Product Material: ABS+Tempered Glass
- Input interface: Type-C port
Fast Wireless Charging requires a PD30W or above adapter.
Indicators and Protection
- Standby mode: the white LED light keeps on.
- Charging mode: the ice blue LED light keeps on.
- FOD function: when putting metal or magnet objects on the charger, the ice blue LED light will flash 6 times and stop charging.
- Perfect protective function based on over-voltage, over-current, over-temperature, and short-circuit protection.
Attention
- Please do not vigorously extrude or collide.
- Please do not dismantle or put it into fire or water when the product is powered on, to avoid short circuits or leakage.
- Please do not use it in severely high temperatures, high humidity, or corrosive environment, to avoid damage to the circuit leakage.
- Please do not put the magnetic strip or chip card (Such as an ID card, bank card, etc.) on the charging pad to avoid causing the magnetic card to lose efficacy.
- Please do not put the metal (Such as coins etc.) on the charging pad when charging, to avoid damage from heating.
FCC STATEMENT
Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, is the device shown to fully comply with the FCC RF Exposure requirements of KDB 447498.