Shenzhen Mgctech FDC-10 Wireless Charger User Manual
- June 6, 2024
- Shenzhen Mgctech
Table of Contents
Mgctech FDC-10 Wireless Charger
User Manual
Product Features
- One-click automatic rotation function. The wireless charger defaults to the horizontal direction. Click the button on the right back to automatically rotate to 90 degrees in the vertical direction. Click the button again to rotate back to the horizontal direction.
- Built-in two coils, adjustable bottom feet, it supports wireless charging of various large-size phones.
- The touch button (with a charging indicator) at the bottom right side controls the opening and clamping of the two clips. Anti-slip silicone on both bottom feet and two clips, Type-C charging port.
- Built-in stepper motor, it works with low noise.
- NPO capacitors, lower charging temperature, and high charging efficiency.
- Standby mode: the LED indicator at the bottom keeps green
- Charging mode: the LED indicator light at the bottom keeps blue, it turns green once remove the receiver.
- FOD function: when put metal or magnet objects on the charger, the blue and green LED indicator light flash 6 times for reminding.
- Perfect protective function based on over-voltage, over-current, over-temperature, and short-circuit protection.
Specification
Input | DC 12V/1.5A,9V/1.67A,5V/2A |
---|---|
Output | 15W/10W/7.5W/5W |
Product Standard | Qi |
Charging Distance | <10mm |
Charging Efficiency | <80% |
Product Dimension | t1527665.3mm |
Product Material | ABS+Tempered Glass |
Fast wireless charging requires a quick 18W or 18W above adapter.
Product Parts Description 1
Product Parts Description 2
Product Operating Guide
- Please make sure the product connects to the power before use.
- The green LED indicator light is on if connected with power.
- The LED indicator light will flash and the product stops charging when the current is too large or there is a foreign object. Do not wirelessly charge the phone if a similar situation happened.
- Touch the smart button at the bottom to open the arms and place the phone on the charger, then the phone will start wireless charging and the arms lock automatically. Only need to touch the smart button at the bottom to release your arms if you want to take out the phone.
- Please purchase the wireless receiver module or case separately (Not included in the product) if your phone does not support wireless charging.
Attention
- Please do not vigorously extrude or collide.
- Please do not dismantle or put it into fire or water when the product is power on, to avoid short circuit or leakage.
- Please do not use it in severely high temperatures, high humidity, or corrosive environment, to avoid damage to the circuit leakage.
- Please do not put the magnetic stripe or chip card (Such as ID card, bank card, etc.)on the charging pad to avoid causing the magnetic card to lose efficacy.
- Please do not put the metal (Such as coin etc.) on the charging pad when charging, to avoid damage from heating.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance between 20cm of the radiator your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>