FS FALLSAFE FS241.02 Work Positioning Belts and Sit Harness Instruction Manual
- June 9, 2024
- FS FALLSAFE
Table of Contents
FS241.02 Work Positioning Belts and Sit Harness
Instruction Manual
INSTRUCTION MANUAL
WORK POSITIONING BELTS AND
SIT HARNESS – According to the Regulation (EU) 2016/425
FS241.02 Work Positioning Belts and Sit Harness
**ADDITIONAL INFORMATION
**
MARKING/ LABELS
EQUIPMENT RECORD
ALL PERIODIC EXAMINATIONS SHOULD BE RECORDED BY THE COMPETENT PERSON. THIS RECORD SHOULD BE KEPT WITH THE EQUIPMENT DURING THE WHOLE LIFE TIME.
1 – PRODUCT| 2 – REF. NUMBER (SEE THE EQUIPMENT LABEL)| 3 – SERIAL NUMBER (SEE
THE EQUIPMENT LABEL)| 4 – MANUFACTURING DATE (SEE THE EQUIPMENT LABEL)
5 – PURCHASE DATE| 6 – DATE OF THE FIRST USE
7 – OTHER RELEVANT INFORMATION
PERIODIC EXAMINATION AND REPAIR HISTORY
8 – DATE| 9 – REASON FOR ENTRY (PERIODIC EXAMINATION OR REPAIR)| 10 – DEFECTS,
REPAIRS, ETC.| 11 – NAME & SIGNATURE| 12 – NEXT PERIODIC EXAMINATION (DUE
DATE)
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | | | |
NOMENCLATURE/ FIELD OF APPLICATION
LISTED ORGANIZATION FOR: (EU) 2016/425 | ISO 9001:2015
SGS FIMOKO OY, P.O. Box 30 (Enshrinement 3) 00211 Helsinki – Finland
NOTIFIED BODY: CE 0598
NOTIFIED BODY
LISTED ORGANISATION FOR CE TYPE APPROVAL:
SGS United Kingdom Ltd, Weston-Super-Mare, BS22 6WA, UK
NOTIFIED BODY: CE0120
NOTIFIED BODY
LISTED ORGANISATION FOR EU TYPE APPROVAL:
VVUÚ. a.s, Heartsick 1337/7 – 716 07 Ostrava – Radiance, Czech Republic
NOTIFIED BODY: CE1019
BELT SIZE CHART
| S/M | 75 – 115 CM |
|---|---|
| L/XL | 90 – 135 CM |
| XXL | 105 – 150 CM |
| Universal | 75 – 135 CM |
DONNING AND SETUP
SPECIFIC INSTRUCTIONS
INSTRUCTION MANUAL
WARNING: READ ALL INFORMATION CONTAINED IN THE TWO INSTRUCTIONS: GENERAL
AND SPECIFIC.
Before using the Personal Protection Equipment (PPE) you must read carefully
and understand the safety information described on general instruction and the
specific equipment instructions. ATTENTION!!! If you have any doubt about the
product, if you need others language version of the instructions for use,
declarations of conformity or any question about the PPE, please contact us:
www.fallsafe-online.com.
WARNING: The manufacturer and the seller decline any responsibility in
case of incorrect use, improper application or modifications/ reparations by
persons not authorized by FALL SAFE®. First, adjust the positioning lanyards
and then attach the connector of the end of the lanyards to the positioning
side D-ring of your harness. Pass the rope through a reliable anchor point
EN795. Attach the connector on the other lanyard end to the positioning
D-ring. You can attach the positioning lanyard to a ring anchor point.
WARNING: The rope must be taut to prevent accidents. Never connect the
lanyards directly to a structure (cable, bar, etc.) having a slope greater
than 15° because the fall length may then exceed 0.6m. Make sure that the
lanyards it´s taut.
WARNING: Karabiners must always be used with the gate closed and locked.
Systematically verify that the gate is securely locked by pressing it with
your hand. Avoid contact with sharp or abrasive surfaces and objects. The
FS241.0X product series only be used by trained and/ or otherwise competent
persons or the user should be under the direct supervision of a trained and/
or otherwise competent person. Before using the sit harness FS241.0X, the user
should carry out a suspension test in a safe place to ensure that the harness
is the correct size, has sufficient adjustment and is of an acceptable comfort
level for the intended use. Attention: Always check the buckles or adjusting
devices during the use. Always check whole harness regularly for any damage
during use and the necessity to withdraw it from use if any damage or defect
is found. Attention! The use of a single harness of type D not coupled with a
harness of type C can lead to risks of injuries. The harness can be used in
mountaineering activities, for the be-lay techniques, abseiling and via
ferrata routes, etc. Attention! Before each use, pre-arrange a suitable rescue
plan that could be executed in a safe and efficient way. The FS241.01/03 +
FS241.02/04 is intended for mountaineering, including climbing. The FS241.01
and the FS241.03, without the legs (FS241.02 and FS241.04) it´s only to work
position. How to dress: firs open the belt Pro Style buckle and pass your legs
into the FS241.02/ 04 webbing (E1) making if necessary the adjustment
according the image B1/B2. Close/ connect (E2) the buckle Pro Style and made
the adjustment according the pictures “B” – Pro Style. For best fit you can
adjust (B1/ B2) the 3 bars buckle (E3) at the belt side. The rope attachment
point it´s identified in the pictures E6 and can be connected (preferential)
using a karabiner EN362 or made this union by a knot (figure of eight – E5).
To assembly the legs you must pass the 20mm webbing loop into the belt
according the picture “E”.
Attention: always check and read the others instructions relative to the
equipment intended to be used principally when it’s damp and ice conditions.
The FS267 arborist harness only be used by trained and/ or otherwise competent
persons or the user should be under the direct supervision of a trained and/
or otherwise competent person. Before using the FS236, the user should carry
out a suspension test in a safe place to ensure that the harness is the
correct size, has sufficient adjustment and is of an acceptable comfort level
for the intended use. Attention: Always check the buckles or adjusting devices
during the use. Always check whole harness regularly for any damage during use
and the necessity to withdraw it from use if any damage or defect is found.
Attention! The use of a single harness of type D not coupled with a harness of
type C can lead to risks of injuries. Attention! Before each use, pre-arrange
a suitable rescue plan that could be executed in a safe and efficient way. How
to dress: firs open the belt IZY quick buckle and pass your legs into the
padding legs (F1). Close/ connect (F2) the IZY quick buckle on the waist strap
and made the adjustment according the pictures “B – IZY quick buckle”. For
best fit you can adjust the Velcro® parts (F3) at the webbing legs. Connect
the small IZY quick buckle (F4), following the instruction in the pictogram “B
– IZY quick buckle” and pull the webbing according you angle necessity to use
to the propose. Note that the bridge angle it´s different if this strap it´s
more or less adjusted (F5). For the bridge adjust it´s necessary regulation on
the lateral 3 bars buckle (F6/ F7). The pictogram F7 represent the connections
points for positioning and suspension. The rope bridge (F8) can be replaced by
a competent person making an stopper knot. Stopper Knot Tying Instructions: F9
– Form a small loop at the end of a line by running tag end over standing
line. F10 – Tie an overhand knot around standing line. F11 – Pull overhand
knot tight and feed tag end through noose (loop) end. F12 – Pull tag end all
the way through and slide knot down tight. F13 – Pull both ends
tight.Attention: always check and read the others instructions relative to the
equipment intended to be used principally when it’s damp and ice conditions.
ADDITIONAL INFORMATION
AI1 – Acceptable Temperature; AI2 – Storage; AI3 – Annual Inspection; AI4 –
Cleaning; AI5 -Drying; AI6 – Hazards; AI7 – Risk of death; AI8 – Attention;
AI9 – Right; AI10 – Wrong; AI11 – Check.
MARKING/ LABLES
ML1 – Brand name; ML2 – Manufacture date; ML3 – Serial number; ML4 – Product
reference; ML5 – Size/ Length; ML6 – European Standard; ML7 – European
Standard; ML8 – Additional information; ML9 – CE Marking – complies with (EU)
2016/425; ML10 – Notified body – which carries out product quality management;
ML11 – Instruction icon; ML12 – Manufacture address; ML13 – Maximum load;
ML14 – Fasten icon; ML(H) – QR Code;
EQUIPMENT RECORD
1-Product; 2-Reference Number; 3-Serial Number; 4-Manufacturing Date;
5-Purchase Date; 6-Date of first use; 7-Other relevant information; 8-Date;
9-Reason for entry; 10- Defects,Repairs,Etc; 11-Name & Signature; 12-Next
periodic examination
NOMENCLATURE/FIELD OF APPLICATION
The waist belt is approved for the user, including tools and equipment
weighing up to 140 kg. This device is not suitable for fall protection and
that the waist belt should not be used if there is a foreseeable risk of
hanging up the user or exposure to unwanted tension. When using a positioning
system, the user usually relies on support, so it is necessary to consider
the need to use a backup as a fall arrest system. For safety, it is essential
to use an anchorage point located at or above belt level. With the waist belt,
it is necessary to regularly check the fastening and adjusting elements
during use. Prior to first use, perform a comfort and adjustability test in a
safe place to ensure that the seat harness is the correct size, has
sufficient adjustment, and has an acceptable level of comfort for the intended
use. Warning: for your safety, we recommend that you always take a safe step,
such as the FS800-SP2, to ensure the effects of suspension trauma when using
the FS241 or FS267 series.
NFA1 – Work positioning steel D-ring – EN358 (DO NOT USE FOR FALL ARREST);
NFA2 – Steel buckles – 3 Bars; NFA3 – Work positioning aluminium D-ring –
EN358 (DO NOT USE FOR FALL ARREST); NFA4 – Webbing keepers; NFA5 – Aluminium
IZY buckle; NFA6 – Steel ring/ webbing for attach tools and/ or bag (MAXIMUM
LOAD 15 KG); NFA7 – Work positioning loop webbing – EN358 (DO NOT USE FOR FALL
ARREST); NFA8 – Aluminium O-ring – EN12277 (DO NOT USE
FOR FALL ARREST); NFA9 – Aluminium buckle with D-ring Pro Style; NFA10 –
Polyester webbing; NFA11 – Polyamide rope Ø 10.5mm; NFA12 – Aluminium anchor
plate; NFA13 – Steel Deluxe buckle; NFA14 – Aluminium O-ring (DO NOT USE FOR
FALL ARREST)
DONNING AND SETUP
DS(A) – Pass the belt around your waist; DS(B) – Connect the buckle of the
belt; DS(C) – Make sure the buckle is well connected; DS(D) – Pull the webbing
strap in order to adjust the work positioning belt to a perfect fit.
Positioning use
DS1 – Adjust the positioning lanyard; DS2 – Attach the connector to the
positioning D-ring; DS3 – Pass the rope through a safe anchor; make sure that
the lanyard is taut; DS4 – Attach the connector to the positioning D-ring;
Restriction use
DS5 – Attach the connector on the other lanyard extremity to the positioning
D-ring; DS6 – Alternatively attach the positioning lanyard to a fixed anchor
point.
50-7046-G_STD2023_R0
EN795:2012-B
FALL SAFE ONLINE, LDA
Zona Industrial da Variola, Rue B – Lotte 54
4480-620 Vila do Conde
Portugal, EU
www.fallsafe-online.com
E-mail: support@fallsafe-online.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>