mgctech IC-10CQ Wireless Charger User Manual
- July 22, 2024
- MGCTECH
Table of Contents
mgctech IC-10CQ Wireless Charger
FAQ
- Q: What should I do if the green light does not turn on when connected to power?
- A: Check if the power source is working correctly and ensure a proper connection between the charger and the power supply.
- Q: Can I use any adapter for fast wireless charging?
- A: Fast wireless charging requires QC or PD adapters for optimal performance. Make sure to use a compatible adapter for fast charging.
- Q: How do I know if my phone is wirelessly charging?
- A: When the phone is placed on the charger and charging begins, the ice blue light will start flashing to indicate the charging process.
Product Features
- Built-in magnet and wireless charging transmitter coil, placing the magnetic phone will automatically adsorption and start wireless charging.
- Standby mode: The RGB light runnning three laps and it keeps green.
- Charging mode: the ice blue breathing light keeps flashing.
- FOD function: when put metal or magnet objects on the charger, the ice blue light will flash for reminding the wireless charging stops working
- Perfect protective function based on over-voltage, over-current, over-temperature and short-circuit protection.
Specifications
- Input: DC 9V/2.5A,5V/2A
- Output: 15W/5W
- Product Standard: Qi2
- Charging Distance: 10mm
- Charging Efficiency: 80%
- Product Dimension: 5830.258mm
- Product Material: ABS+Glass+Zinc Alloy
Overview
Fast wireless charging
- Fast wireless charging requires QC or PD adapters.
Product Operating Guide
- Please make sure the product connect to the power before using.
- The green light keeps on if connected with power.
- The ice blue light will flashes and the product stop charging when the current is too large or there is foreign object. Do not wireless charging the phone if similar situation happened.
- Please purchase the wireless receiver module or case separately (Not included in the product) if your phone do not support wireless charging.
Attention
- Please do not vigorously extrude or collide.
- Please do not dismantle or put it into fire or water when the product is power on,to avoid short circuit or leakage.
- Please do not use it in severely high temperature, high humidity or corrosive environments, to avoid damage to the circuit leakage.
- Please do not put the magnetic strip or chip card (Such as ID card,bankcard etc.)on the charging pad to avoid to cause magnetic card lose efficacy.
- Please do not put the metal (Such as coin etc.) on the charging pad when charging,to avoid damage from heating.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>