Cloudy Bay LJD006GBBLWH-XX 6 Inch BLE LED Gimbal Recessed Down Light Installation Guide

Cloudy Bay LJD006GBBLWH-XX 6 Inch BLE LED Gimbal Recessed Down Light

Specifications

Installation Overview

1. Turn off power at the source.
2. Make a hole in the ceiling with a template in the package.
3. Carefully remove the knock-out with a screwdriver or punch.
4. Open the connector’s box cover. Feed the supply wire into the knockout hole using the connector and make all connections inside the junction box using the EZ connectors (see picture below). Connect the 120V line wire to the black wire. Connect the neutral wire to the white wire. Connect a bare copper wire to the grounding terminal of the outlet box. Put on the junction box cover.
5. Use it as an air-tight recessed downlight, MIN height above the ceiling is 2 inches. Put in the Connector and female connector, raise the springs to a vertical position and push the light kit into the hole until it stays. Fit in the ceiling. Push the light kit on one side to change the angle and illuminate the target area.
6. Hold the trim and push the recessed down upwards until it separates from the light kit, move the cable away from the rubber ring, and if necessary, cut a hole in the rubber ring so that the cable can go out.
7. Use it as a Non-airtight recessed downlight, above ceiling height can range from 1-3/8 inch to 2 inches. Tester: use a manual to set up those lights

FAQ

• How do I contact customer service if I have a problem with the product?
• Please contact us through email at smart@cloudybaylighting.com or call Toll-Free Phone Number: 1(877)-870-5171.
• Is there any warranty on this product?
• Yes, there is a 3-Year Limited Warranty. For details, refer to the warranty section of the installation instructions.
• What should I do if the light fixture shows any visible defect?
• Immediately discontinue use and contact customer service for a replacement or refund.
• Can I control the light manually through the ON/OFF wall switch?
• Yes, but ensure each turn-on is more than 10 seconds to prevent accidental pairing. If the light blinks due to wrong operation, let it blink for 10 seconds, then turn off
• and back on the wall switch to recover to paired status.
• What should I check if there is no voltage or if the light is not working correctly?
• Check that the circuit is not powered, ensure the junction box is grounded properly, and verify that the wire connection between the junction box and light kit is correct. For more information, please refer to the user manual and voice control guide provided with the product.

Thank you for purchasing CloudyBay Smart LED Lighting Fixtures.

BLUETOOTH SMART LED RECESSED GIMBAL DOWNLIGHT

GENERAL: All electrical connections must be by local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections, contact and obtain the services of a qualified electrician. Use UL or IEC-approved wire only for input/output connections.
Remove fixture and mounting components from the box, and make sure that no parts are missing, by referencing the illustration in the illustration instructions.

• Turn power off before installation, inspection, or removal.
• Use all necessary precautions while performing this procedure.
• Consult a qualified electrician to ensure the correct branch circuit conductor. Min 90°C supply conductors.
• Properly ground electrical enclosure. THE OUTLET BOX MUST BE PROPERLY GROUNDED.
• DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS, OTHERWISE SAFETY WILL BE COMPROMISED.
• Contact us through smart@cloudybaylighting.com.

TROUBLESHOOTING

• Check that the line voltage is correct.
• If there is no voltage, then check all connections.
• Check that the junction box is grounded properly.
• If the light kit does not light:
• Check the wire connection between the junction box and the light kit is correct

PRODUCT CARE After Sales Service

1. Please discontinue using the product right away if the product shows any visible defect and contact customer service.
2. If there is any problem with our lights for non-human reasons, please contact customer service, and we will send you brand-new replacements without the need to return goods or a full refund.
3. If you are not completely satisfied with the product after installation but prefer not to disassemble it, contact us right away, and we will provide comparable compensation.

WARRANTY

3-Year Limited Warranty
LIMITED WARRANTY: This fixture is warranted to be free from defects in workmanship and material for up to 3 years. Based upon reasonable household usage, when used by package and included instructions. If this fixture does not last for the period guaranteed, the manufacturer will send you a replacement fixture upon receipt of the returned fixture, register receipt, and proof of purchase. To contact us, please email us at smart@cloudybaylighting.com to find out how to return the fixture. We are committed to making high-quality products. Returning the fixture will help us monitor and further improve product quality. This replacement is the sole remedy available, and LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED.

PACKAGE CONTENTS

• smart@cloudybaylighting.com.
• info@cloudybaylighting.com.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

INSTALLATION INSTRUCTIONS

INSTALLATION OVERVIEW

1. Turn off power at the source.

2. Make a hole in the ceiling with a template in the package.

3. Carefully remove the knock-out with a screwdriver or punch.

4. Open the connector’s box cover. Feed the supply wire into the knockout hole using the connector and make all connections inside the junction box using the EZ connectors (see picture below). Connect the 120V line wire to the black wire. Connect the neutral wire to the white wire. Connect a bare copper wire to the grounding terminal of the outlet box. Put on the junction box cover.

5. Use it as an airtight recessed downlight, MIN height above the ceiling is 2inch
   Put on the Connector and female connector, raise the springs to a vertical position and push the light kit into the hole until it stays flat in the ceiling. Push the light kit on one side to change the angle and illuminate the target area.

6. Hold the trim and pull the round cover upwards until it separates from the light kit, move the cable away from the rubber ring, and if necessary, cut a hole in the rubber ring so that the cable can go out.

7. Use it as a Non-airtight recessed downlight, above ceiling height can range from 1-3/8inch to 2inch.

8. See the user manual to set up those lights.

Note: This product is a smart light, using Direct Digital Controls rather than triac dimming. Here are two dimming way for your reference:

1. Download Cloudy Bay’s APP, go to the product group or single product page, and adjust the brightness and CCT of white light or colour light on the control panel; you can also go to the home page, dick product group or single product’s common function, adjust brightness and colour temperature.
2. Control with a smart voice device such as Google Assistant or Amazon Alexa if you have installed it successfully.

CONTACT

QUESTIONS? COMMENTS? SUGGESTIONS? COMPLAINTS?

• Please contact us through
• Toll-Free Phone Number: (1) 877-870-5171
• smart@cloudybaylighting.com.
• or info@cloudybaylighting.com.
• We will do our best to make it right for you. Thank you very much!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>