Mgctech CB-T10 Wireless Charger User Manual
- September 6, 2024
- MGCTECH
Table of Contents
Mgctech CB-T10 Wireless Charger
Product Introduction
This is a multifunctional desktop magnetic 3 in 1 auto rotation wireless charger, which can wirelessly charge mobile phones, headphones, and watches at the same time by power supply.Bid farewell wired shackles and start wireless experience.
Product Usage Guide
- Please connect the product through the Type-C quick charging cable to the QC or PD above power adapter.to ensure that it supports fast wireless charging.
- Built-in stepper motor and touch button to support wireless charger automatic rotation function, to compatible with different size of qi-enabled smart phonts.
- Press and popup the iWatch charging stand, place the Apple Watch to start wireless charging with 2.SW output.
- Press and popup the earphone charging stand, place the earphone case to start wireless charging with 2.SW output.
- Touch-sensitive design that allows for the automatic rotation of your smartphone with different viewing angle.(Please do not rotate it by hands to avoid of damage the product. Please reconnect the power supply and touch button to adjust it to the correct position .)
Product Parts Description
- Touch button for rotation
- Charging area for phone
- Charging area for earphone
- Charging area for watch
- Indicator Light
- Type-C input port
Specifications
- Input : DC 5V/3A, 9V/3A
- Phone Output : 5W, 10W, 15W
- Product Standard : Qi
- Earphone Output : 2.5W
- Watch Output : 2.5W
- Charging Distance : E10mm
- Charging Efficiency : <80%
- Product Dimension : 76•76•109mm
- Product Material : Aluminum Alloy + Tempered Glass
- Input interface : Type-C port
Indicators And Protection
- Standby mode: the white LED light keeps on.
- Charging mode: the ice blue LED light keeps on.
- FOD function: when put metal or magnet objects on the charger, the ice blue LED light will flash’s 6 times and stops charging.
- Perfect protective function based on over-voltage, over-current, over-temperature and short-circuit protection.
Attention
- Please do not vigorously extrude or collide.
- Please do not dismantle or put it into fire or water when the product is power on,to avoid short circuit or leakage.
- Please do not use it in severely high temperature,high humidity or corrosive environment,to avoid damage to the circuit leakage.
- Please do not put the magnetic strip or chip card (Such as ID card, bankcard etc.)on the charging pad to avoid to cause magnetic card lose efficacy.
- Please do not put the metal (Such as coin etc.) on the charging pad when charging.to avoid damage from heating.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radiofrequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>