ZMIRNE H3 Floor Heater User Manual
- June 16, 2024
- ZMIRNE
Table of Contents
User Manual Floor heater
Models：H3
Thank you for choosing our heater. Please read this user manual carefully before use and keep it for future reference
Product drawings and parameters
Product parameters：
| Product name | H3 Fan heater |
|---|---|
| Product Size | 148145401.5mm |
| Weight | About 2KG |
| Voltage | 120V（US）/230V(EU/UK） |
| Power | 1500W |
Second, important security instructions
Read and follow all safety information and instructions. For future reference.
When using electrical appliances, basic precautions should be followed at all
times to reduce the risk of fire, electric shock and personal injury,
including the following:
-
Please read all the instructions before using this heater.
-
The surface of the heater will become hot during use. To avoid burns, do not touch hot surfaces with bare hands. Use the handle when moving the device.
-
Do not place combustible materials such as furniture, pillows, bedding, paper, clothing, and curtains at least 3 feet (0.9 meters) from the front and top of the radiator, don’t approach the side of back.
-
This equipment is not intended for use by persons (including children) with physical, sensory or mental impairments or lack of experience and knowledge unless they are supervised or instructed in the use of the equipment by a person responsible for their safety.
-
Use as a toy is prohibited. Extra care must be taken when used by children. Children should be supervised to ensure that they do not play with the machine or remote control.
-
Do not use a damaged power cord or plug, or operate the heater after failure, drop, or damage in any way. The heater shall be returned to the authorized service for repair.
-
Do not use outdoors or on wet surfaces.
-
Do not touch the plug or any part of the machine with wet hands.
-
For use in dry locations only. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations.
Do not place the heater where it could fall into a tub or other container of water. Do not use or store in areas where it could get wet or near a bathtub, shower or pool. -
Do not run wiring under furniture or appliances. Route cords away from traffic areas and where they will not be tripped over.
-
To disconnect the heater, gently press the On/Off button to turn it off and allow it to cool before unplugging it from the outlet.
-
Do not insert or let foreign matter into any vent or exhaust, otherwise it may lead to electric shock, fire or damage to the heater.
-
To avoid possible fire, do not use with any openings or exhaust vents blocked and keep away from dust, lint, hair and any items that will reduce airflow. Do not put any objects into the air inlet or outlet as this may result in electric shock or fire or damage to the unit.
-
The heater has internal heating or arc or spark components. Do not use in areas where gasoline, paint, or flammable liquids are used or stored.
-
Use this heater only as described in this user’s guide. Any other use not recommended by the manufacturer may result in fire, electric shock, personal injury or other property damage.
-
To prevent to overload , make sure no other device is plugged into the same socket or another socket connected to the same circuit.
-
If the fit between the plug and the receptacle is loose or the plug becomes very hot, the receptacle may need to be replaced. Consult a qualified electrician to replace the receptacle.
-
It is normal for plugs and power cords to feel hot. The plug or power cord feels hot or deformed, possibly as a result of wear and tear on the power outlet. The worn socket should be replaced before further use of the heater. Inserting the heater into a worn socket may cause the power cord to overheat or catch fire.
-
The output of the heater may change and its temperature may become high enough to burn exposed skin. It is not recommended for people with reduced heat sensitivity or non-responsiveness to avoid burns.
-
Make sure the heater is located on a stable, secure surface to eliminate the possibility of tipping over.
-
Always plug the heater directly into a wall outlet. Do not use extension cords or repositionable power connectors (outlet/power strip) together.
-
make sure the plug is fully inserted into the proper socket. Remember that sockets deteriorate with age and continuous use: check the plug regularly for signs of overheating or distortion. Do not use a damaged outlet and call your electrician.
-
Check the unit or power cord for damage during shipping.
-
Do not attempt to modify or repair the product yourself. Doing so may void the warranty and result in damage or personal injury. Only service technicians should disassemble or repair this product.
-
Choking Hazard: the remote control contains a small battery. Keep the remote out of reach of children and do not swallow batteries. If you swallow a battery, seek medical attention immediately.
-
If the machine does not work properly, is hit hard, dropped, damaged, left outdoors or dropped in water, do not use and contact customer service support.
-
When cleaning, storing or not using, be sure to turn off the heater to cool it and unplug it from the Power Outlet.
Note: There may be a whiff of smoke or smell the first time the device is
run.
This indicates that there is a drop of oil on the heating coil during the
manufacturing process. It will evaporate quickly and should not happen again.
Danger: high temperatures may occur under unusual conditions. Do not
partially or completely cover or block the front or rear of this heater.
Operation and function
Product drawings:
1. Display screen
2. Infrared remote control receiving position
3. Adjust the wind direction knob up and down
4. Windscreen
5. Hot Zone| 6. Shake your head from side to side
7. Base
8. Press the button
9. Hand-held position| 10. Air Intake
11. Dust-proof net
12. Air intake button hand position
13. Power Cord
---|---|---
Operation and function：
| Click to power on/click to power off Long press for more than 2 seconds to
open/close the child lock
---|---
| Mode key: Short Press Loop HI-LO-ECO-cool breeze
| Click to decrease the temperature. Enter ECO mode directly when long
pressing this button
| Click to increase the temperature. Enter ECO mode directly when long
pressing this button
| Click to turn on/off the shaking head
| Click/long press to adjust timing time
Use methods:
Note before use:
Please check if all product parts are complete, if they are incomplete, to
avoid causing injury, please do not use them.
- Please be sure to use this product on a horizontal surface, imbalance will lead to the top of the product switch in an abnormal state, so that the product can not work after boot, therefore, please be sure to use the electric heater on the horizontal surface.
- Before using the remote control to control the product, please point the remote control at the heater to operate, keep a certain distance between the two, and ensure that there is no barrier between the remote control and the heater.
The plug is plugged into an outlet to supply power, the power switch on the heater base is turned on, the heater drips to indicate power on standby, and the LED screen lights up.
-
After power on, the display will enter standby mode and the icon will go off after power on.
When the power is turned on by clicking the On/Off button, the default is to start the high mode, the HI icon on the display lights up and the screen digits show the ambient temperature. Press the On/Off button again to turn off the heater, if the heater is running, it will take 30 seconds to dissipate the heat and the countdown time will be shown in the LED display. -
When the heater is working, press the M button repeatedly to switch modes, cycling between high grade (HI) – low grade (LO) – ECO ( ) – cold air grade (FA).
-
When the heater is working, click the + or – key will enter ECO mode directly. You can adjust the temperature you want by + -, the adjustment range is between 20℃ – 30℃ (68℉ – 86℉), then the LED screen ECO mode icon is on.
-
Click to turn on/off the shaking head located on the top of the product body Shaking head operation.
Click again on the shaking head located at the top of the product body. Press the key, the product body will start to swing left and right Key, the heater will stop swinging left and right.
-
Click/long press to adjust the timer key on the top of the product body or the timer and timer key on the remote control, timer start, timer range: 1-12H, cycle. Display the number 01-12 to set the timer after the icon is displayed. During setting timer, press and hold the number to jump quickly. Press and hold to cancel the timer when the timer setting is finished.
-
ECO energy-saving mode::
When the ECO mode is entered, the heater will automatically start heating or stop heating according to the set temperature, and the heater will automatically adjust the working mode between high (HI) and low (LO). When the ambient temperature reaches the set temperature, the heater stops working. When the ambient temperature falls below the set temperature, the heater will start again.
Remote Control:
Please note: For convenience, the product can be operated by the
corresponding button on the remote control.
Notes:
- When using the remote control, ensure that the heater is plugged into an energized electrical outlet and that the power switch on the base is turned on;
- Operate the key on the remote control, it will directly enter ECO mode. At this time,you can use the key to change low mode (Ll), high mode (Lo).
Other features:
Memory function
- If the power is not off, the heater will always remember your last setting (temperature and operating mode) when you turn it on again.
Auto screen off
- If nothing is done for 15 seconds, the LED screen will automatically turn off.
The LED screen can be activated again by any button/remote
24-hour automatic shutdown
- When the heater works continuously for 24 hours without any other operation, it will turn off automatically.
Remote control child lock
You can lock the heater directly with the key on the remote control, then all
the keys on the body are inoperable and the LED screen will show CL.
Tip-over protection
- When the heater is tipped over or tilted too far, the heater will automatically shut off and display fault code “P4” on the LED display with a beeping sound.
Place the heater back on a flat, level and stable surface and keep it upright.
Then turn it on again.
Overheat protection
- When the ambient temperature is above 50°C / 122°F, the heater will stop heating and trigger an overheat alarm with a fault code “FF” on the LED display and a beeping sound.When the ambient temperature drops below 50°C / 122°F, unplug the power supply and turn it back on.
Replace the battery of controller
- Remove the battery case cover in the direction indicated by the arrow.
- Replace with new coin cell batteries, make sure the “+” and “-” poles are correctly positioned.
- Reinstall the battery cover.
Attention:
- If you need to replace it, please replace it with a new battery of the same type.
- Take out the battery when you don’t use the remote control for a long time.
- Do not attempt to remove the battery.
- Please do not put the battery into the fire, the battery may explode or leak.
Cleaning and maintenance
It is recommended that the heater be cleaned at least once during the
operating season and prior to off-season storage to provide optimum
performance levels.
Before cleaning, be sure to disconnect the unit from the power supply by
turning it off and unplugging it from the electrical outlet.
- Press the on/off button on the top of the heater to turn it off and wait for the machine to cool down. Unplug the Power Plug and wait for the heater to cool down completely.
- Use only a soft cloth to gently wipe the outer surface of the heater.
- Do not use any detergent.
- Do not immerse the heater in water and do not allow water to drip into the motor housing. Make sure not to get the heating element and switch wet.
- After removing the rear cover of the heater, remove the dust screen and clean the dust with a soft brush or air gun, and make sure to dry it before putting it into the machine if it gets wet;
- When storing, you can cover the heater to prevent dust from entering. Store it in a cool, dry place and arrange the cable away from traffic areas so that it cannot be tripped over or damaged.
Warning
- Do not allow water to flow inside the heater, as this may result in fire or electric shock hazard.
- Any other service shall be performed by an authorized service representative.
Troulbe clearing
The following troubleshooting guidelines address the most common problems:
| Problem | Possible reasons | Solutions |
|---|---|---|
| Screen failure | Ff-overheat protection | |
| (ambient temperature above 50 ° C/122 ° F) | Unplug it from the Power Supply |
and turn it back on when the environment is normal (temperature drops to 122 °
F below 50 ° C) .
P 4-flip protection| Connect the plug to an energized electrical outlet.
Heater No start| The power cord was not inserted correctly.| Connect the plug
to an electrified power outlet.
Overheat protection activated.| Turn off the heater, unplug and let cool.
Check and remove any objects on or near the heater. Wait 5-10 minutes, then
reinsert the unit.
No power passes through the unit.| Make sure your circuit breakers or fuses
are working properly. Make sure your heater is placed on a flat surface.
Set temperature below room temperature.| Make sure the thermostat is set above
room temperature.
The heater stopped suddenly during the heating process| The ambient
temperature is over 50 ° C/122 ° F.| When the ambient temperature drops below
50 ° CI 122 ° F, UNPLUG IT from the Power Supply and turn it back on.
The heater tipped over.| Place it on a flat, level, and stable surface and
keep it upright. Then open it again.
1-year limited warranty:
Products delivered to you in a new state in the original packaging, under
normal use and service of the material and process defects warranty period of
one year, warranty period maintenance or replacement can not extend the
original warranty period, for products requiring a dated proof of purchase for
warranty service, a copy of your dated sales slip will satisfy this
requirement.
This warranty does not cover accessories or consumables that are not covered
by warranty or replacement, such as dust nets, back covers, etc. . This
limited warranty covers all defects encountered during normal use of the
product and does not apply to:
- Product loss or damage resulting from misuse, negligence, improper handling, improper packaging, alteration, accident, current fluctuation, improper use, failure to comply with operation or maintenance instructions, falls, scratches and wear as specified in safety instructions or other documents is considered to have resulted from misuse, misuse or failure to comply with Operation Requirements as specified in the user manual or other product documentation.
- Use of other parts or consumables (other than those sold) that may cause damage to the product.
- Products that have been disassembled or repaired without permission; for customer service and warranty, please contact us here