ROUGH COUNTRY 10918 Skid Plate Mounting Kit Installation Guide
- September 3, 2024
- Rough Country
Table of Contents
ROUGH COUNTRY 10918 Skid Plate Mounting Kit
Product Information
Specifications:
- Product: TOYOTA 2010-20 4 Runner Skid Plate Spacer
- Kit Contents:
- 5/8 Spacers x6
- Tools Needed:
- 17mm Wrench or Socket
- Hardware Included:
- 10mm x 45mm Bolt x2
- 10mm x 65mm Bolt x2
- 10mm Flat Washers x4
- Clear Retainer x4
Installation Instructions:
- Install one of the 10mm x 65mm bolts into the front hole of the skid plate using one of the 10mm flat washers.
- Place two of the supplied 5/8 thick spacers onto the bolt and secure using the clear retainer. Repeat on the opposite front hole.
- Install one of the 10mm x 45mm bolts into the rear hole of the skid plate. Place one spacer onto the bolt and secure using one clear retainer. Repeat on the opposite rear hole.
- Place the skid plate on the vehicle and thread the bolts into the mounting holes.
- Tighten the four bolts installed into the skid plate using a 17mm socket.
FAQ:
-
Q: What torque specs should I use for tightening the bolts?
A: Refer to the provided torque specs chart in the manual for Grade 5, Grade 8, Class 8.8, and Class 10.9 bolts based on their sizes. -
Q: Do I need any additional tools for installation?
A: No, a 17mm wrench or socket is sufficient for installing the skid plate spacer kit.
Thank you for choosing Rough Country for all your vehicle needs.
- Please read the instructions before beginning installation. Check the kit hardware against the kit contents shown below. Be sure you have all the needed parts and know where they go.
- If a question exists, please call us at @1-800-222-7023. We will be happy to answer any questions concerning this product. Check all fasteners for proper torque. Check to ensure adequate clearance between all components.
- Periodically check all hardware for tightness.
Kit Contents
- 5/8” Spacers x6
Tools Needed
- 17mm Wrench or Socket
Hardware Included
- 10mm x 45mm Bolt x2
- 10mm x 65mm Bolt x2
- 10mm Flat Washers x4
- Clear Retainer x4
Torque Specs
| Size | Grade 5 | Grade 8 | Size | Class 8.8 | Class 10.9 |
|---|---|---|---|---|---|
| 5/16” | 15 ft/lbs | 20ft/lbs | 6MM | 5ft/lbs | 9ft/lbs |
| 3/8” | 30 ft/lbs | 35ft/lbs | 8MM | 18ft/lbs | 23ft/lbs |
| 7/16” | 45 ft/lbs | 60ft/lbs | 10MM | 32ft/lbs | 45ft/lbs |
| 1/2” | 65 ft/lbs | 90ft/lbs | 12MM | 55ft/lbs | 75ft/lbs |
| 9/16” | 95 ft/lbs | 130ft/lbs | 14MM | 85ft/lbs | 120ft/lbs |
| 5/8” | 135ft/lbs | 175ft/lbs | 16MM | 130ft/lbs | 165ft/lbs |
| 3/4” | 185ft/lbs | 280ft/lbs | 18MM | 170ft/lbs | 240ft/lbs |
INSTALLATION INSTRUCTIONS
- Install (1) on the 10mm x 65mm bolts into the front hole of the skid plate using (1) of the 10mm flat washers. See Photo 1.
- Place (2) of the supplied 5/8” thick spacers onto the bolt and secure using the clear retainer. See Photo 2.
- Repeat steps 1 and 2 on the opposite front hole of the skid plate.
- Install (1) of the 10mm x 45mm bolts into the rear hole of the skid plate. Then place (1) spacer onto the bolt and secure using (1) a clear retainer. See Photo 3.
- Repeat step 3 on the opposite rear hole of the skid plate.
- Place the skid plate on the vehicle and thread the bolts into the mounting holes. See Photo 4.
- Tighten the (4) bolts installed into the skid plate using a 17mm socket. See Photos 5 and 6.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>