BEGA 50 143.2 Wall and Ceiling Light Instruction Manual

: August 30, 2024
: BEGA

Table of Contents

BEGA 50 143.2 Wall and Ceiling Light
Specifications
FAQs
DIMENSION
Instructions for use
Product Description
Overvoltage protection
Installation
Replacing the LED module
Cleaning Maintenance
CONTACT INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50 143.2 Wall and Ceiling Light

Specifications

Material: Aluminium luminaire with matt surface finish
Light cover: Light-diffusing synthetic material
Width: 6.5 mm
Connection terminal: 2.5@
LED power supply: 220-240 V x 0/50-60 Hz DC 176-276 V
DALI controllable with 1 address Basic insulation between mains and control cables
LED power reduced to 15% in DC operation

FAQs

Q: What should I do if the luminaire is not working?
- A: Check the power supply, and connections, and ensure proper installation by a qualified electrician. If issues persist, contact customer support.
Q: Can I use this luminaire outdoors?
- A: Refer to the product manual for suitability for outdoor use. Ensure proper weatherproofing if used outside.
Q: How do I control the brightness of the luminaire?
- A: Use the DALI control system with the specified address to adjust brightness levels.

DIMENSION

Ceiling and wall luminaire for indoor use

Instructions for use

Application

Ceiling and wall luminaire · indoor luminaire made of impact-resistant synthetic diffuser and aluminum housing.
Luminaire with free-radiating and uniform light distribution for linear illumination in the interior.

Product Description

Luminaire made of aluminum, matt surface finish
Light-diffusing synthetic luminaire cover 3 elongated fixing holes
Width 6.5mm
Connection terminal 2.5@
Earth conductor connection 2-pole connecting terminal for digital control
Complies with flicker requirements by IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit 220-240 V x 0/50-60 Hz DC 176-276 V
During DC operation the LED power is reduced to 15%
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
– Safety mark
– Conformity mark
Weight: 3.8 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage per DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp

Module connected wattage 52.2 W
Luminaire connected wattage 62 W
Rated temperature ta=25 °C
Ambient temperature ta max=35 °C

50 143.2K3

Module designation 6x LED-0694/930
Color temperature 3000 K
Color rendering index CRI >90
Module luminous flux 8310 lm
Luminaire luminous flux 6511 lm
Luminaire luminous efficiency 105 lm/W

50 143.2K4

Module designation 6x LED-0694/940
Color temperature 4000 K
Color rendering index CRI >90
Module luminous flux 8790 lm
Luminaire luminous flux 6724 lm
Luminaire luminous efficiency 108,5 lm/W

Please note: If the luminaire is to be mounted onto a metallic, electroconductive surface, it is mandatory to make sure that the mounting surface is connected conductive to the earth conductor of the luminaire!

Note:

If you a planning a linear arrangement of several luminaires, you must keep a minimum distance of 30mm between the luminaire caps for installation reasons.
The synthetic cover of the luminaire body can expand by max. 7mm when hot.

Installation

LED are high-quality electronic components!
- Please avoid touching the light output opening of the LED directly during installation or relamping.
- Remove the luminaire from the packaging and put it down on a soft surface with the rear of the housing open.
- Undo the hex socket screw on the side of the luminaire cap.
- Push the luminaire body on the housing to the side until the luminaire body can be removed freely.
- Make an earth conductor connection.
- Push silicone sleeves over the lines and make an electrical connection to the terminals.
- For digital control please use the connecting terminal DA, DA.
- In case this terminal is not used the luminaire will be operated at full light output.
- Secure the luminaire housing to the installation surface with the fixing materials provided or other suitable materials.
- For wall installation note the position of the application “arrow down”.
- Pick up the luminaire body and insert the retention bolt into the opening in the housing (keyhole).
- Before you connect the LED, first swing up the two locking levers of the LED connection terminal.
- Make the LED connection at the luminaire terminal – use long-nose pliers if necessary.
- Check that the poles are correct, black: “Driver -“, read: “Driver +”.
- Close the locking levers of the LED connection terminal.
- Push the luminaire body against the housing cap.
- Make sure not to damage the connection wires when pushing in.
- Tighten the hex socket screw on the side of the housing cap.

Replacing the LED module

The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module.
The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system. Undo the hex socket screw on the side of the luminaire cap. Push the luminaire body on the housing to the side and swing up the two locking levers of the LED connection terminal.
Disconnect the LED connection at the luminaire terminal. Push the luminaire body on the housing to the side until the luminaire body can be removed freely.
Unscrew the retention bolts (hexagon socket SW 3). Loosen the Pin-Torx countersunk screw (T 20). Slide the luminaire cover over the LED modules to the side.
Remove the LED module. Install the replacement LED module.
Please follow the installation instructions for the LED module.
The defective luminaire cover must be replaced. Reassemble the luminaire again in reverse order. Make sure not to damage the connection wires when pushing into the housing cap.