ROUGH COUNTRY 50016 2 Inch Leveling Kit Instruction Manual

ROUGH COUNTRY 50016 2 Inch Leveling Kit

Product Information

Specifications:

• Model : 921500160
• Product : FORD 2024 Ranger Raptor 2 Leveling Kit
• Compatibility : Developed for a 305/70R17 tire on the factory 17-wheel

Product Usage Instructions

Tools Needed:

• Players
• 8mm Socket or Wrench
• 10mm Socket or Wrench
• 15mm Socket or Wrench
• 16mm Socket or Wrench
• 18mm Socket or Wrench
• 21mm Socket or Wrench
• 1 1/16 Wrench
• 6mm Allen Wrench
• Hammer

Front Installation Instructions:

1. Chock the rear wheels and lift the front of the vehicle using a floor jack. Place the vehicle on jack stands and remove the front wheels.
2. Remove the tie rod end nut using a 21mm wrench. Retain hardware for reuse.
3. Remove the ABS wire on the knuckle using a 10mm wrench. Retain hardware for reuse.

Thank you for choosing Rough Country for your suspension needs.
Rough Country recommends a certified technician install this system. In addition to these instructions, professional knowledge of disassembly/reassembly procedures as well as post-installation checks must be known. Attempts to install this system without this knowledge and expertise may jeopardize the integrity and/or operating safety of the vehicle.

Please read all the instructions before beginning the installation. Check the kit hardware against the parts list. Be sure you have all the needed parts and understand where they go. Also please review the tools needed list and make sure you have the needed tools.

PRODUCT USE INFORMATION

WARNING :

• As a general rule, the taller a vehicle is the easier it will roll. We strongly recommend seat belts and shoulder harnesses should be worn at all times. Avoid situations where a side rollover may occur.
• Braking performance and capabilities are decreased when significantly larger/heaver tires and wheels are used. Take this into consideration while driving. Also, speedometer recalibration is necessary when larger tires are installed.
• Do not add, alter, or fabricate any factory or after-market parts that increase vehicle height over the intended height of the Rough Country product purchased. Mixing component brands, lifts, and/or combining body lifts with suspension lifts voids all warranties. Rough Country makes no claims regarding lifting devices and excludes any implied claims. We will not be responsible for any product that is altered.
• If you desire a different look or if the vehicle has a toolbox or added weight in the rear, please consult with your sales representative about block /u-bolt options.

This 2” kit was developed for a 305/70R17 tire on the factory 17” wheel.

NOTICE TO DEALER AND VEHICLE OWNER
Any vehicle equipped with any Rough Country product must have the “Warning to Driver” decal installed on the sun visor or dash. The decal is to act as a constant reminder for whoever is operating the vehicle of its unique handling characteristics.

INSTALLING DEALER— It is your responsibility to install the warning decal and to forward these installation in-structions on too the vehicle owner for review and to be kept in the vehicle for its service life.

Torque Specs

• Size Grade 5 Grade 8 Size Class 8.8 Class 10.9
• 5/16” 15 ft/lbs 20ft/lbs 6MM 5ft/lbs 9ft/lbs
• 3/8” 30 ft/lbs 35ft/lbs 8MM 18ft/lbs 23ft/lbs
• 7/16” 45 ft/lbs 60ft/lbs 10MM 32ft/lbs 45ft/lbs
• 1/2” 65 ft/lbs 90ft/lbs 12MM 55ft/lbs 75ft/lbs
• 9/16” 95 ft/lbs 130ft/lbs 14MM 85ft/lbs 120ft/lbs
• 5/8” 135ft/lbs 175ft/lbs 16MM 130ft/lbs 165ft/lbs
• 3/4” 185ft/lbs 280ft/lbs 18MM 170ft/lbs 240ft/lbs

Kit Contents

10MMHEXBAG

• 6 – 10mm x 50mm Bolt
• 6 – 10mm Serrated Flange Nut
  • 2 – 2” Leveling Spacer

Tools Needed :

• Players
  • 8mm Socket or Wrench
  • 10mm Socket or Wrench
  • 15mm Socket or Wrench
  • 16mm Socket or Wrench
  • 18mm Socket or Wrench
  • 21mm Socket or Wrench
• 1 1/16” Wrench
• 6mm Allen Wrench
• Hammer

FRONT INSTALLATION INSTRUCTIONS

1. Chock the rear wheels and use a floor jack to lift the front of the vehicle. Place the vehicle on jack stands and remove the front wheels.
2. Use a 21mm wrench to remove the tie rod end nut. Retain hardware for reuse. See Photo 1.
3. Use a 10mm wrench to remove the ABS wire on the knuckle. Retain hardware for reuse. See Photo 2.
4. Use an 8mm wrench to remove the bolt holding the sensor arm bracket to the upper control arm. Retain hardware for reuse. See Photo 3.
5. Use an 18mm wrench with a 6mm Allen to remove the sway-bar link from the knuckle. Retain hardware for reuse. See Photo 4.
6. Loosen, but do not remove the upper ball joint nut with an 18mm wrench. See Photo 5.
7. Use a hammer to strike the knuckle where the upper ball joint is to release the taper. Use the 18mm wrench to finish removing the upper ball joint nut. See Photo 6.
8. Unplug the strut connections. See Photo 7.
9. Undo the clips holding the black wire. See Photo 8.
10. Remove the lower strut hardware using a 1 1/16” socket. Retain hardware for reuse. See Photo 9.
11. Use a 15mm wrench to remove the three upper strut nuts. Remove the front strut from the vehicle. Retain hardware for reuse. See Photo 10.
12. Use a set of pliers to remove the roll pin on the strut top hat. See Photo 11.
13.  Place the strut in a strut compressor and clock the strut top hat 180 degrees. Install the strut spacer onto the strut using the factory hardware. Tighten with a 15mm wrench. See Photo 12.
14. Install the strut using the supplied 10mm serrated flange nuts. Tighten with a 16mm wrench.
15. Reinstall components using the factory hardware in reverse order of disassembly.
16. Reinstall the wheels and lower the vehicle to the ground.

POST INSTALLATION INSTRUCTIONS

1. Check all fasteners for proper torque. Check to ensure adequate clearance between all rotating, mobile, fixed, and heated members. Verify clearance between exhaust and brake lines, fuel lines, fuel tank, floorboards, and wiring harness.
2. Perform a steering sweep to ensure front brake hoses have adequate slack and do not contact any rotating, mobile, or heated members. Inspect rear brake hoses at full extension for adequate slack. Failure to perform hose check/replacement may result in component failure.
3. On some vehicles, the front lower skirting will need to be trimmed if using certain wheel/tire combinations and with heavy offset wheels. Trim only as needed.
4. Activate ate four-wheel drive system and check the front hubs for engagement.
5. Have a qualified alignment center align the vehicle immediately. Realign to factory specifications.
6. Perform headlight check and adjustment to proper settings.
7. Check and retighten wheels at 50 miles and again at 500 miles
8. All kit components must be retightened at 500 miles and then every 300 miles after installation. Periodically check all hardware for tightness.
9. Install the “Warning to Driver” decal on the sun visor.

NOTE : Installation of larger tires will require speedometer recalibration.

By purchasing any item sold by Rough Country, LLC, the buyer expressly warrants that he/she complies with all applicable, State, and Local laws and regulations regarding the purchase, ownership, and use of the item. It shall be the buyer’s responsibility to comply with all Federal, State, and Local laws governing the sales of any items listed, illustrated, or sold. The buyer expressly agrees to indemnify and hold harmless Rough Country, LLC for all claims resulting directly or indirectly from the purchase, ownership, or use of the items.

FAQ

Q: What tire size is this leveling kit compatible with?
A: This kit was developed for a 305/70R17 tire on the factory 17-wheel

Q: What tools are needed for installation?
A: Tools required include plyers, various socket wrench sizes (8mm, 10mm, 15mm, 16mm, 18mm, 21mm), a 1 1/16 wrench, a 6mm Allen wrench, and a hammer.

Q: What torque specifications should be followed during installation?
A: Refer to the provided torque specs table for the appropriate values based on the bolt size and grade.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>