TigerTough W0523021 40/20/40 Seat Cover Installation Guide

TigerTough W0523021 40/20/40 Seat Cover

Product Specifications

• Part Number: W0523021
• Product Type: 40/20/40 Seat Cover
• Pieces:
  • (1) Driver Back
  • (1) Driver Bottom
  • (1) Passenger Back
  • (1) Passenger Bottom
  • (1) Console Back
  • (1) Console Bottom
  • (2) Seat Headrests
  • (1) Console Headrest
  • (2) Stringlocks

Product Usage Instructions

General Care Instructions:

1. In most cases, dirt, debris, spills, and pet hair can be removed by wiping with a damp cloth.
2. Seat covers can be removed and machine washed on a low-temperature setting using mild detergent. Drip dry or machine tumble dry on a no heat cycle. Straps should be coiled and secured with rubber bands for machine washing and drying.
3. Soil may be removed with spray cleaner or detergent and water.
4. Oil or grease stains should first be treated with a dry cleaning solvent followed by a spray cleaner or detergent and water.
5. Do not use bleach.

Important: Airbag Compatibility

Your seat has seat side airbags. For maximum safety in the event of a crash, these airbags must not be restricted. Ensure that the tearaway flap (stitched with white thread) and the orange TigerTough tag are facing the door to allow the airbag to deploy.

Installation Instructions

Preparation:

• Unhook from seat bottom.
• Pull down to detach from seat bottom.
• Slide seat forward and raise to the highest position, if possible.
• Remove headrest by pressing in tabs at the base of headrest and pulling up.
• Pull yellow plug out of the bottom of the seat.
• Unhook elastic straps from under the seat bottom.

Install Seat Bottom Cover

• Put cover over seat bottom.
• Tuck outside of cover behind plastic trim. Tuck inside of cover between seat bottom and center console.
• Tuck outside string between seat bottom and trim. Inside string goes down and under the seat. Strings must run in front of rear seat mounts.
• Pull strings tight.
• Secure strings with StringLock.
• Push top flap between seat back and seat bottom. Slits in cover line up with wires in the seat back.
• Run front flap over seat adjustment levers, wires, and brackets.
• Pull front flap tight and fasten to Velcro on top flap.

The StringLock:

1. Run one string through the channel on the end of the StringLock.
2. Pull the string tight, pulling the StringLock towards one edge of the seat. Press the string into the clamp, locking it in place.

FAQ

Q: What should I do if my seat covers get damaged?

A: Your seat covers are covered by a two-year warranty. If your covers get damaged within this period due to normal use, contact us for repair or replacement options.

Q: Can I machine wash the seat covers?

A: Yes, you can machine wash the seat covers on a low-temperature setting using mild detergent. Follow the care instructions provided for best results.

case sensitive link
ttcovers.com/52321video

Basically, you break it, we buy it. Seriously.

Your new seat covers are covered by a two-year, unconditional, no B.S. warranty.
That means that if you manage to abuse them to a point that they can’t perform like they’re supposed to within two years of when you bought them, we’ll make it right.
Depending on what is more practical, we’ll ei-ther repair or replace the damaged cover.

General care instructions

1. In most cases dirt, debris, spills and pet hair can be removed by wiping with a damp cloth.
2. Seat covers can be removed and machine washed on low temperature setting using mild detergent. Drip dry or machine tumble dry on a no heat cycle. Straps should be coiled and secured with rubber bands for machine washing and drying.
3. Soil may be removed with spray cleaner or detergent and water.
4. Oil or grease stains should first be treated with a dry cleaning solvent followed by a spray cleaner or detergent and water.
5. Do not use bleach.

IMPORTANT: AIRBAG COMPATABILITY
YOUR SEAT HAS SEAT SIDE AIRBAGS. For maximum safety in the event of a crash, these airbags MUST NOT be restricted.
Your cover has been engineered with a tearaway flap (stitched with white thread) that will allow the airbag to deploy. Ensure that this flap & the orange TigerTough tag are facing the door.
TigerTough is not responsable for any issues resulting from incorrectly installed seat covers.

Preparation

1. Slide seat forward and raise to highest position, if possible.
2. Remove headrest by pressing in tabs at base of headrest and pulling up
3. Pull yellow plug out of bottom of seat.
4. Unhook elastic straps from under seat bottom.

Install Seat Bottom Cover

1. Put cover over seat bottom.
2. Tuck outside of cover behind plastic trim. Tuck inside of cover between seat bottom and center console.
3. Tuck outside string between seat bottom and trim, where the back and bottom meet. Inside string goes down and under seat. Strings must run in front of rear seat mounts.
4. Pull strings tight.
5. Secure strings with StringLock. See next page for StringLock instructions.
6. Push top flap between seat back and seat bottom. Slits in cover line up with wires in seat back.
7. Run front flap over seat adjustment levers, wires, and brackets.
8. Pull front flap tight and fasten to Velcro on top flap.

THE STRINGLOCK

1. Run one string through the channel on the end of the StringLock.
2. Pull the string tight, pulling the StringLock towards one edge of the seat. Press the string into the clamp, locking it in place.
3. Run the second string through the StringLock just like the other one.
4. Pull the loose end of the second string until everthing is tight and lock it into place as well.

Install Seat Back Cover

1. Turn seat back cover 3/4 of the way inside out and pull over seat back.
2. Line holes in cover up with headrest holes and work holes around plastic trim.
3. Continue pulling the cover down over the seat, unrolling it as you go.
4. Push front flap between seat back and seat bottom.
5. Pull front flap tight and fasten to Velcro on seat back.
6. Long flap on rear of seat back fastens to Velcro on underside of seat bottom cover.

Install Headrest Cover

1. Put headrest back in seat by pressing plastic tabs and pushing down on headrest.
2. Pull cover over head rest with “loop” Velcro in front and “hook” Velcro in rear.
3. Fasten Velcro tabs together under headrest.

Install Center Console Back (No Storage)

1. Remove headrest by pressing tabs at base of headrest and pulling up.
2. Place cover over back, working holes around headrest trim.
3. Fasten Velcro flap around seat belt.
4. Fasten Velcro seam down rear of back.
5. Push front flap between seat back and bottom.
6. Pull flap tight and fasten to Velcro on back.

Install Center Console Bottom

1. Tip seat bottom up and pull cover over it.
2. Pull side flaps tight and fasten to factory upholstery under seat bottom.
3. Push top flap between seat back and seat bottom.
4. Pull flap tight and fasten to Velcro on bottom of cover.

Install Headrest Cover

1. Put headrest back in seat by pressing plastic tabs and pushing down on headrest.
2. Pull cover over headrest with “loop” Velcro in front and “hook” Velcro in rear.
3. Fasten Velcro tabs together under headrest.

References

• YouTube

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>