PETLIBRO PLCT002 Infinity DIY Cat Tree User Manual
- June 9, 2024
- PETLIBRO
Table of Contents
Infinity DIY Cat Tree
User Manual
Model: PLCT002
This product is for indoor use only. Read and save the instructions.
COMPONENTS
Before assembly, be sure to identify and sort all components shown below.
PLATFORM AND BASE
CUSHIONS
SUPPORT PARTS
OTHERS
ACCESSORIES
ATTENTION
Side A faces up when assembling the platform.
Place the side A of the base face down, then install the anti-slip pad as
shown in the picture.
WARNINGS & CAUTIONS
Please read and follow all warnings and instructions to avoid pet injury or property damages.
- Place your cat tree indoors, away from direct sunlight or damp areas.
- Keep all tools and instructions in a safe place for future reference.
- This cat tree is intended for cat use only, please keep children away.
- Keep all small parts away from children and pets to avoid choking hazards.
- Never climb, rock, shake, step or hong on the cot tree.
- Cot trees should be placed on a flat, level surface for stability.
- Check your cat tree often for loose screws or parts that might need re-tightening.
- Do not place heavy items on the product.
- Do not sit or stand on the product.
- Inspect product for damage and discard if any part gets worn or damaged.
- Wrong assembly may cause the product lo fall over and cause injury.
- For safety, please wear gloves when handling tools and during installation.
- Single-layer weight capacity : 10kg/22lbs.
- Total weight capacity: 50kg/110lbs.
BASIC METHODS
Assemble Two Scratching Posts/Wooden Poles
- Twist a third of the bolt into the lower scratching post/wooden pole.
- Twist the upper scratching post/wooden pole into the bolt until it can’t move.
Assemble the Platform and Scratching Posts/Wooden Poles| Assemble the Base and
Scratching Posts/ Wooden Poles| Assemble the Top Perch and Scratching Posts/
Wooden Poles
---|---|---
• Side A faces up.
1.Twist a third of the bolt into the lower scratching post/wooden Pale.
2.Pass the bolt through the hale.
3.7wist another scratching post/wooden pole into the bolt until it can’t
move.| • Side A faces down.
Hold the scratching post/wooden pole and lighten the 50mm long screw from the
bottom with the hex wrench.| • Side A faces up.
Hold the scratching post/wooden pole and tighten the 50mm long screw from
above with the hex wrench.
Assemble the Cushion and Platform
-
Remove the sticker paper under the cushion.
-
Put the cushion on the platform and press firmly to stick tightly. As the picture shows.
Assemble the Cushion and Top Perch
-
Remove the sticker paper under the cushion.
-
Put the cushion on the top perch and press firmly to stick tightly. As the picture shows
Assemble the Tunnel and Platform| Hang the Toy Ball| How to Use the 16mm
Wooden Block
---|---|---
• Side A faces up.
I Poss the 30mm long screw through the board and tunnel.
2. Use a 13mm open ended spanner to tighten the nut inside the tunnel.
3. Hold the nut, and tighten the screw with the hex wrench.
Note: To prevent cats hitting their heads while playing, please use the
30mm long screw.| Poss the rope of fluff ball through the hole al the end of
the top perch cushion and tie a knot as shown in the picture.| I. Align the
l6mm wooden block with the wooden pole first, then align
its hole with the hole on the platform.
2.Hold the wooden pole, and tighten the 50mm long screw from above with the
hex wrench.
How to Use the PVC Sticker
After assembly, use the PVC sticker to cover the screw hole.
WRONG ASSEMBLY
WARNING Wrong assembly cause the product to fall over and cause injury.
Do
not use the scratching post or wooden stick to support the top perch or
platform only on one side.
CLEANING INSTRUCTIONS
Clean the Felt Bag
Caution: To avoid damage to the fabric
Do not machine wash the felt bog.
Do not use brush to wash the felt bog.
Never place it in a dryer.
Never expose it to direct sunlight.
Never use any other direct heat source (such as a hairdryer) to dry it.
Do not use bleach.
l .Unzip and remove the felt bag.|
2.Submerge the felt bog in cold water, odd some mild detergent safe to use on
felt.| .Soak the felt bog in water for a few minutes. Gently hand-wash the
felt bog.
4.Rinse and repeat until water is clean.| 5.Absorb the remaining water with a dry cloth.| 6.Let it air dry.
Clean the Boards, Scratching Posts, and Wooden Poles
*Caution: Do not wash in water
To remove hair and dust, use a vacuum cleaner.
I .Moisten a soft cloth with soapy water.| 2.Spot clean the stains and soiled areas with a damp cloth.| 3.Air dry the wet area completely.
WARRANTY
- 12-month warranty
- Life-time support
Please contact our customer service at
support@petlibro.com for warranty extension or
any questions about the product.
For more information, please visit
www.petlibro.com.
4 DIY WAYS The 4 Installation Methods Below are for Reference.
WARNING: To prevent pets injury, if you do not install it in the
recommended 4 DIY ways, please make sure the woy you install will not cause
the product to tip over.
ATTENTION : Please Install from the Bottom to Top When Assembling.
01 ATTENTION: To ensure safety, it’s best to place the cot tree against a
wall or in a corner.
03 ATTENTION: To ensure safety, it’s best to place the cat tree against a wall or in a corner.
04 ATTENTION: To ensure safety, it’s best to place the cat tree against a wall or in a corner.
CLibro Corp. All Rights Reserved.
Distributor: Shenzhen Libro Technology Co., Limited
Address: Building 3, Cloud Park, Shenzhen, Chino, 518129
Manufacturer: Ganzhou Aigesen Wooden Based Panel Co., Ltd
Address: Furniture Industrial Park, Nankang District, Ganzhou, Jiangxi
Province,China
EPA EST NO. I 7055-CHN- l
Mode in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>