TigerTough W0555066 Antimicrobial Rear Seat Covers for Ford Truck Installation Guide
- August 28, 2024
- TigerTough
Table of Contents
TigerTough W0555066 Antimicrobial Rear Seat Covers for Ford Truck
Specifications
- Part Number: W0555066
- Product Type: 60/40 Seat Cover
- Pieces Included:
- (1) 40 Portion Back
- (1) 40 Portion Bottom
- (1) 60 Portion Back
- (1) 60 Portion Bottom
- (1) Armrest
- (3) Headrests
Product Usage Instructions
Installation Steps
-
1. Remove all three headrests by pushing in the buttons on the base of the mounts and pushing the headrest upward to remove them. - Unlatch the 60-portion seat back and tip the seat bottom up to move the seat back away from the cab. Release the seat back by pulling the tab on the side of the seat bottom.
Hey there!
- It’s not rocket science, but following the instructions will make installing your seat covers a lot easier. We promise.
- If you have any questions, comments, or issues, we’re here to help! You can reach us at 507.246.3545 (call or text) or email orders@tigertough.com.
PART NUMBER PRODUCT TYPE PIECES
W0555066
60/40 SEAT COVER
- (1) 40 PORTION BACK
- (1) 40 PORTION BOTTOM
- (1) 60 PORTION BACK
- (1) 60 PORTION BOTTOM
- (1) ARMREST
- (3) HEADRESTS
VIDEO INSTRUCTIONS
case sensitive link
ttcovers.com/55566video
2-YEARS
IT`S COVERED
Basically, you break it, we buy it.
Seriously.
Your new seat covers are covered by a two-year, unconditional, no B.S.
warranty.
That means that if you manage to abuse them to a point that they can’t perform
like they’re supposed to within two years of when you bought them, we’ll make
it right. Depending on what is more practical, we’ll either repair or replace
the damaged cover.
General care instructions
- In most cases, dirt, debris, spills, and pet hair can be removed by wiping with a damp cloth.
- Seat covers can be removed and machine washed on a low-temperature setting using mild detergent. Drip dry or machine tumble dry on a no-heat cycle. Straps should be coiled and secured with rubber bands for machine washing and drying.
- Soil may be removed with spray cleaner or detergent and water.
- Oil or grease stains should first be treated with a dry cleaning solvent followed by a spray cleaner or detergent and water.
- Do not use bleach.
Install Seat Cover
page 1
- Remove all three headrests.
- Push the buttons on the base of the mounts and push the headrest upward to remove.
- Unlatch the 60-portion seat back.
- Tip the seat bottom up (this moves the seat back away from the back of the cab). Reach behind and release the seat back by pulling the little metal nubbin
- The release of the seat back is better explained in the install video. ttcovers.com/55566video
- Next, tip the seat back and bottom forward together by pulling the tab on the side of the seat bottom.
- Undo all of the tabs on the seat back portion.
- Slide it under the seatbelt, and work it down over the seat back as shown.
- Press the cover under the headrest mounts for a clean, finished look.
- Make sure the latch is properly exposed at the back.
- Tip the armrest down to pull it out through the gap in the cover.
- Work the ‘tail’ of the armrest cutout up between where the armrest hinges on the seat. This is a tight fit! Moving the armrest back and forth will help.
page 2
- Pull the ‘tail’ up and secure it to the tab on the inside of the cutout…
- ….it should look like this.
- Push the three tabs between the seat back and bottom.
- Tipping the seat back at an angle helps with this.
- The little tab on the edge is there so that you don’t have to pinch that wire.
- Pull them all tight and secure them as shown.
- Put the armrest cover on.
- Make sure the loop comes through the gap in the cover for it.
- Work the little ‘tail’ from the bottom of the armrest through the gap where the armrest hinges (this is better shown in the video) ttcovers.com/55566video
- Next up – the seat bottom.
- Slide it on like a big pillowcase. The holes for the carseat anchors should be on top.
page 3
- Work the cover down the seat as shown.
- Fasten the little flap on each side
- Push the flaps from the top ofthe seat between the seat back and bottom, and then pull them tightly and secure them on the bottom.
- Make sure the little release loop is coming through the slot in the cover for it.
- Next up – the 20-portion seat back.
- Release it from the back of the cab by pulling the release loop on the side.
- Slide the cover on with the long flap at the front. Turning the cover partly inside out at first helps get it snug at the top of the seat.
- Press the cover under the headrest mounts.
- Make sure the release strap is coming through the hole in the side.
- Unroll the cover the rest of the way down the seat back.
- Push the flap in between the seat back and bottom.
page 4
- Pull the tab tight and secure at the back.
- Now, cover the seat bottom.
- The holes for the car seat anchors should be on the top.
- Push the flap from the top in between the seat back and bottom.
- Pull it tight and secure it at the bottom.
- Make sure the release loop is coming through the hole in the cover for it.
- Put the headrests back on and cover them.
- The long tab goes towards the front and secures up inside the back of the headrest.
- Same with the little middle headrest.
- And, you’re finished!
FAQ
- Q: What is the warranty for the seat covers?
- A: The seat covers are covered by a two-year, unconditional warranty. If they fail to perform within two years due to abuse, they will be repaired or replaced.
- Q: How do I care for the seat covers?
- A: General care instructions include removing headrests and following the installation steps provided in the manual.
- Q: How can I reach customer support?
- A: You can contact customer support at 507.246.3545 (call or text) or email orders@tigertough.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>